MERCEDES REPAIR TOOLS
Click Here to Buy Tools


Click for Larger Image and more information

Set 5 Tools for Mercedes repair.

1.Hub Securing Bar 113-0040 Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v-belt is not in place and cannot be used to lock the hub. Applicable:M112 & M113

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine - M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900-589-0307-00 Another old number for this was 117-589-0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V-8 19 86 and NEWER

4. Long Pattern Thin wrench 36mm. Comes with rubber handle grip.

5. Thin Wrench 65mm with an 8mm overall thickness and an overall length of 16 inches for proper leverage. Mercedes ref: 120-589-0201-00.

You get all 5 tools with this purchase (above).






Click for Larger Image and more information

Metal Clad Bushing R&R Kit
Please read carefully: Tool set for replacing the wheel carrier bushing at the rear wheel carrier assembly (where all the links attach), and it works as good as the factory tool.
Some people wind up taking off every single link and bending the dust sheild while trying to R&R this bushing (with a standard shop press).
This tool is worth its weight in gold.
Although this tool is an aftermarket tool for the MB tool# 202 589 00 43 00, it worked excellent in the field, and its about 1/2 the cost of the OE MB tool.
It works on Mercedes-Benz chassis: 124, 129, 140, 170, 171, 201, 202, 203, 208, 209, 210, 215, 220, 221, 230, spanning 1984-present models
(not every model however, mainly the ones listed above).

w124 (1986-1995 300E/E320, 300D, E300D, 400E, 500E,etc), R129 (1992-2002 SL Models), w140 (Sclass from 1991-1998), R170, R171 (All SLK models, thru current), w201 (all 190E/D models), w202 (C class 1993-2000) w203 (c class 2000-2006), w208 & w209 (all CLK models), w210 (E-Class 1996-2001), w215 (CL - Class Coupe 1999-2006), w220 and w221 (S Class 1996-2006, S class 2006-present), and R230 (the new SL roadster). It is used to replace MB Bushing #220-352-02-27, which are now #221-352-00-27.

SAME AS 202 589 00 43 00 Removal and Installation Wheel Carrier Support Joint
(REPLACES) 140 589 07 43 00 Removal and Installation Tool
(REPLACES) 201 589 05 43 00 Removal and Installation Tool

This set comes complete with all the proper components to efficiently get the job done right. This tool works both on the car or on the bench.





Click for Larger Image and more information


Master Link - Timing Chain Tool Double Row Set-up
SAME AS BENZ NUMBER 000-589-5843-00 Used for proper assembly of timing chain master link. OM601, OM602, OM603, OM615, OM616, OM617

Single row adapter and/or KIT available.
The single row set up is the same price as this kit.....email for more info.






Click for Larger Image and more information


MERCEDES DASH SERVICE TOOL KIT
Set Includes: Ignition "V" shape lock release wires same as Mercedes Number 900-589-0059-00
Plus a pair Long Hooks (overall length 6.5 inches)
(Similar to Mercedes 140-589-0223-00 the mercedes hooks are 7 inches - the ones in this set are 6.5 inches)
You get the radio removal Keys (Pair)
Details:
Ignition Lock Removal (wires) Set for W124, 126, 201
Pair of Hooks for W107, 116, 123, 124, 126, 140, 201
Radio Removal keys FOR "1997 and OLDER" W129, 140, 202, 210.





Click for Larger Image and more information

Mercedes Rail Pin Puller Guide
This Puller has an Overall Length of 85mm and is designed with a thrust bearing to ease the pulling action. Used for the proper extraction of rail pins from cylinder head. Especially useful in restricted spaces where other pullers and slide hammers will notfit. Comes with a 6mm extractor pin. Applicable: Mercedes M102, M110, M115, M116, M117, M130, OM601, OM602, OM603, OM615, OM616, OM617.

In the 4 cylinder and 6 cylinder engines, this tool also removes the timing chain tensioners pivot pin, which is hidden behind a bolt in the front right (facing forward) face of the cylinder head. It of course also removes all of the timing chain guide rail mount pins that are located in the left (facing forward) of the cylinder head, and down in the left face of the engine block. Extremely handy when doing jobs with the engine still in the car, such as headgasket replacement, timing chain tensioner replacement, or timing chain guide rail replacment. Works in all carbureted and fuel injected gasoline, and all diesel injected 4 cylinder and 6 cylinder engines as found in w108, w109, w110, w111, w112 chassis cars built in the 60s, as well as other models that use pins to secure guide rails.





Click for Larger Image and more information


Valve Spring Compressor Kit M0068 For 6 and 8 cylinder engines. Same as Benz Number 123-589-0361-00 Spring Compressor Kit used for R&R of valve spring or rocker arm. Job can be done with the cylinder head on or off the car. Applicable: M 114, 115, 116, 117, 123, 130, 180.






Click for Larger Image and more information


The Original B90-Kit  Designed to efficiently remove or install wheel bearing and hubs of spindle assemblies. Chassis W124, W129, W201, W202 Models with S.R.W.B and I.R.S. Email with any questions.





Click for Larger Image and more information


Coil Spring Compressor Kit for Mercedes. For front and rear coil springs. Applicable: W107, W116, W123, W124, W126, W129, W140, W170, W201, W202, W208 and W210.
Comes with carrying case.
Compress front & rear axle springs on models with idler arm & some MacPherson type suspensions.
Same as 924-589-0231-00.
Telescopic range 120mm-325mm. You get 2 Plates sizes 90/150mm and 2 Plates size 70/130mm





Click for Larger Image and more information


MacPherson Strut Coil Spring Compressor
Includes 3 pairs of Jaws. For compressing several types of Mac type front and rear springs.
Especially for 110, 120 and 130 springs found on many Mercedes.

Shoes (jaws) Sizes
125-215mm
88-160mm
65-125mm
and carrying case

Applicable BMW:
E31, E32, E34, E36, E39, Z3, Z3 coupe
Applicable Mercedes:
W163, 164, 171, 203, 209, 210, 211, 219, 230, 245, 251




Click for Larger Image and more information


Front Lower Control Arm Tools M0062 Press Kit needed for the proper installation of bushings into the front lower control arms. Applicable: Mercedes chassis - W124, W129, W140. Each press washer has its own thrust bearing which eases the pressing action. This reduces friction, wear and tear of the tool, ensuring longevity.





Click for Larger Image and more information
Mercedes Diesel Injection Pump Socket M0019 Mercedes 32 Point Female Socket with 1/2" drive, This socket is used for the R&R of delivery valve of diesel injection pump. Applicable: Mercedes diesel engines. Ref: 617-589-0109-00.





Click for Larger Image and more information


Mercedes Valve Adjustment Wrench Set of 3 Tools Made in Germany by Hazet This three-piece set includes:Hazet Item Numbers 2769, 2769-1 and 2769-3






Click for Larger Image and more information

Mercedes Ball Joint Press Tool M0063 Press Tool for the proper installation of ball joint into steering knuckle. The design of this tool allows for mounting in a vice w/o marring the tool or bending under pressure. Applicable: Mercedes chassis - W116, W123, W126. Big Time-Saver! Made from High Quality Steel, Incorporated with a heavy duty solid thrust bearing, A must for the Professional Mercedes Mechanic! Ref: 116-589-0462-00





Click for Larger Image and more information


Mercedes
Go-No-Go Gauge* Used for checking hydraulic valve lifters Applicable: Mercedes V-8 engines 1976 and Newer * Excluding M119. Ref: 917-589-0623-00





Click for Larger Image and more information


Mercedes Valve Spring Compressor Kit M0069-MASTER Spring Compressor Kit used for R&R of valve spring or rocker arm. Job can be done with the cylinder head on or off the car. Applicable: Mercedes engine - M102, M103





Click for Larger Image and more information


M0068 Valve Spring Compressor Kit M0068 For 6 and 8 cylinder engines. Same as Benz Number 123-589-0361-00 Spring Compressor Kit used for R&R of valve spring or rocker arm. Job can be done with the cylinder head on or off the car. Applicable: M 114, 115, 116, 117, 123, 130, 180





Click for Larger Image and more information


Hub Securing Bar (Reference 113-589-0040-00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v-belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench





Click for Larger Image and more information


Pencil Type Reamer
Size 12 x 1.25 used for removing carbon buildup in Diesel Glow Plugs which is a major cause of glow plug failure.
Applicable: OM 601,615,616,and 617 , MB Ref: 901-589-0053-00






Click for Larger Image and more information


Counter Holder Tool / Harmonic Balancer holder for the front crankshaft pulley Mercedes M112 and M113. This tool was redesigned to fit both versions of the Mercedes-Benz pulley. 112,113,E320,ML320,CLK320,E430,ML430,C320,C43,E55 etc...
Similar to reference (tool) number 112-589-0040-00
C-class from 1998-2005 with V-6 or V-8 engine
E-class from 1998-2005 with V-6 or V-8 engine
SLK-class from 1998-2005 with V-6 engine
CLK-class from 1998-2005 with V-6 or V-8 engine
ML-class from 1998-2005 with V-6 or V-8 engine
SL-class from 1999-2006 with V-8 engine
S-class from 2000-2005 with V-8 engine
G-class from 2002-2007 with V-8 engine






Click for Larger Image and more information


Ball Joint Tool This tool set is used for removing and installing the ball joint into the steering knuckle. Applicable: 211 E Class 2002 and newer. 215 CL Class 2002 and newer. 219 CLS 2006 and newer. 220 S Class 2000 and newer. 230 SL Class 2003 and newer (NOTE: THIS KIT IS THE SAME AS OTHER ITEM M220-0343






Click for Larger Image and more information


Cam Holding Wrench Kit Holds camshaft in 40 degree TDC position (left/right side) 32mm Appl.: 1998 and newer Mercedes-Benz with V6 and V8 engines (M112, M113) 38mm special wrench for turning the cam. This special Cam Securing Master Wrench Kit has all the necessary components to properly adjust and lock the cams into position. Comes as shown with (1) Cam Wrench and (2) Cam Alignment Plates





Click for Larger Image and more information



Special Tool for MERCEDES-Star.
Chrome-plated, with T-handle made of black plastic, for mounting and removing the Mercedes-Star at the engine hood
on class S (W 140), E (W 124 since model 93) and C (W 202






Click for Larger Image and more information


Cup Wrench for Mercedes W202. Used to remove fuel sender retainer





Click for Larger Image and more information

Spark Plug Metal Boot Remover Wrench
Newer Mercedes V-6 engines are equipped with a (2) spark plug wire and/or metal boot per cylindetr set up. This special wrench 17mm with its specific angle along its tapered machined surface of the box end allows it to fit into those metal spark plug boots after the coil pack has been removed. This special tool is the only good way to ensure that the metal boots and plug wires remain damage free during removal.
Overall length is 12.5 inches





Click for Larger Image and more information

This special kit was designed for the crucial task of damage free R&R of front lower control arm, metal clad/ rubber mount bushings. The beauty of this job specific kit is its on-the-car application which allows the technician to tackle the repair without the need for an hydraulic press. Applicable: Mercedes chassis - W202





Click for Larger Image and more information

Mercedes Transmission Dipstick Benz reference number 140-589-1521-00 For determining fluid level newer Mercedes with electronic transmission 722.6 The graduations on the fluid end (plastic dipping end) are: (Range) 25 (low) to 80 (high) The picture is not to scale





Click for Larger Image and more information


Locking Nut M0039 needed for securing the diesel injection pump cam shaft. Applicable:Mercedes OM601, OM602, OM603, OM605, OM606, OM617. Benz Ref: 601-589-0521-00






Click for Larger Image and more information

MERCEDES DASH SERVICE TOOL KIT
Set Includes: Ignition "V" shape Lock release Wires
Ignition Lock Removal wires for W124, 126, 201
(similar to MB Number 900-589-0059-00)


Long Hooks (pair) for W107, 116, 123, 124, 126, 140, 201
Similar to Mercedes 140-589-0223-00
(Please note the original Mercedes hooks are 7 inches in length
the ones in this set are only 6.5 inches)

Radio Removal keys FOR "1997 and OLDER" W129, 140, 202, 210

PLUS YOU GET Ignition Turning Tool (BLUE)
For loosening and tightening the ring (rosette) of the electronic ignition switch.
Applicable: W129, 140, 202 (as of June 1, 1997), 208, 210, 211, 230, 240, 463
The Aluminum will not leave marks on the interior parts.
Benz ref: 210-589-0007-00






Click for Larger Image and more information


This is the best price set on the market...Bar None! The competition does NOT offer this COVERAGE for the price they charge.
This is a Master Set and it is used with BMW, Mercedes, Volkswagen Audi, Porsche and DIN.
FULL COVERAGE on Volkswagen Audi.
What makes this set better is a total of 8 keys for VW Audi and two for BMW plus the grips on the keys are coated for easy use.
You will notice a total of 3 different sets for Volkswagen Audi,  two different tools for BMW and a set for newer Mercedes that will also work with older Mercedes and also works with some Porsche. (Same as Porsche ref: 000-721-957-01)
Here is what you get....Details below...

A. VW Tools (4) Number T10057 Audi A4, A6, A8 and New Beetle
For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
If you have 4 slots VW AUDI this is the set (T10057) you need. This 4 piece set is extremely popular.
The 2 piece VW set is Number VW 3316 New Body Style Passat Jetta Golf . Virtually full coverage for Volkswagen -Audi when you buy this set.

B. BMW Tools are one Pentagon shaped tool with a 3-5/8 inches overall length. Applicable: Most BMWs. This Five sided driver is used to release anti-theft radio mounts. You will also get the special rare very small allen tool for BMW (upper left) For newer BMW E38 & E39 7 SERIES

C. Mercedes Tools covers almost all newer and older vehicles, especially 1992 and newer 129, 140, 163, 202 & 210, Range Rover with Becker Nav System.
The MB Tools also work on Porsche. Appl: Turbo GT, GT2, GT3, Boxster, Cayenne 911, 996 , 987, Carrera etc.
Same as Porsche ref: 000-721-957-01

D. "U" Hooks  for DIN - Ford







Click for Larger Image and more information


Transmission Linkage Bushing Installer / Tool for Mercedes-Benz with automatic transmissions, virtually all later models, some Ford and other vehicles needing this tool to easily and safely push TOUGH nylon bushings into place. Works on different bushing sizes. The design of this tool was initiated by Mr. Robert Allen and has recently been modified and perfected. Robert Allen is a long time Mercedes-Benz Master Technician with 26 years of experience.





Click for Larger Image and more information


SECURITY TORX PLUS BIT SET
5 Point Star Security TORX PLUSŪ Insert Bit Set with Mini-Ratchet
5 Point set includes sizes TS10, 15, 20, 25, 27, 30, 40
Please note there are 10 total bits and only 7 actual sizes - you will get each of the sizes above plus the kit has an extra size 25, 30 and 40 because the 25, 30 and 40 are the popular sizes and tend to wear out (or get lost) faster than the other sizes.
These are Security Torx PlusŪ Tools and they Do NOT work in a standard Torx Fasteners.
Reminder: These are 5 point tools AND THEY ARE TAMPERPROOF - VERY RARE AND HARD TO FIND SET!
You will get both the bit set and the mini-ratchet with this purchase.

Torx, Torx Plus and Camcar are registered trademarks of Textron, Inc. Torx plus is designed to allow greater torque, and to minimize wear






Click for Larger Image and more information


Special 5 Point Tool Made in Germany by Hazet. Rare and Hard to find Star pattern 5 Point Tamperproof driver for Removing and Installing the exterior Mirror on Type 211 (E-CLASS) as well as Type 203 (C-CLASS). High quality tool made in Germany. Lenth of shaft is 200mm and the overall length is 225mm.
Please note: standard torx is 6 point. This tool is 5 point






Click for Larger Image and more information


Two Torx Sets Special Deal
MALE & FEMALE SETS
Male Tamperproof Torx (6 POINT)
Set with 1/4 Drive and 3/8 Drive sizes.
11 Pieces, sizes included: (3/8 drive) T40, T45, T50, T55 and T60.
(1/4 Drive) T10, T15, T20, T25, T27 and T30. Plus you will get the ten piece Female Set
Description: 10 Piece Torx Female Socket Set
3/8 Drive and 1/4 Drive assorted sockets on a rail.
The (smaller) 1/4 Drive Sizes are: E4, E5, E6, E7, E8.
The (larger) 3/8 Drive Sizes are: E10, E12, E14, E16, E18






Click for Larger Image and more information


Set of two tools
First tool (top of image) pictured is a Universal tool is used to separate the ball joint from the spindle support arm. It works on many domestic and import front wheel drive vehicles, and is adjustable for diffrent size ball joints. Using the correct ball joint tool makes a tough job much easier. Factory ball joints are pressed in tight, if you damage the ball joint, the situation gets ugly. Two Stage Ball joint tool -Special steel, galvanized, for removing the ball pivots of steering arms, stabilizers etc.
Plus Universal Ball joint Puller (18-22mm opening), light series, galvanized Specifications Once the puller is positioned on the pin by adjusting the central screw, the joint is removed by turning the side screw. You get both tools with this purchase (above).





Click for Larger Image and more information


New Style Mercedes Oil Wrench 74mm with 14 Points (inside flats - flutes).
Mercedes M102, M103 etc..
Check your manuals for details and size needed.(Measure filter diameter or canister diameter.
See ref number mb# 103 589 0209 00
This is an excellent deal. Other applications include: Audi, VW Golf, and new body Jetta, TDI (Diesel) and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle






Click for Larger Image and more information


SET 2 Repair Tools For Mercedes. This is the correct pin socket required to remove the input flange from the differential on all w110, w111, w108, and w109 chassis Mercedes cars built during 1961 to 1972 with swing axle style rear differential/axle assemblies. More Details:
Diagram on Tool 1a

If you have a leak at the differential input flange oil seal, this tool removes the special nut located down inside the flange. Once this nut has been removed, the flange pulls off, exposing the input seal.
When reinstalling the nut using this tool pay close attention not to over-tighten the nut so that the differential pinion bearings are not damaged.
There is a similar nut and flange at the rear of the transmission, however, it requires socket number TOOL 1b. (see images)

Diagram on Tool  1b

Buy these as a pair, and be well prepared to change out your leaking 40 year old transmission output and differential input seals."
You get both tools with this purchase..






Click for Larger Image and more information

12 Piece Terminal Tools - wire terminal extractor kit
Tools used to release DC wiring terminals from the harness that connect to ECUs, sensors, etc., found on most late model vehicles Special Electrical/Terminal Tools designed to remove wires from terminals without damage. Comes in the handy plastic case






Click for Larger Image and more information
11 Piece Set Interior Tools for Mercedes
Specifically designed set including tools with extra slim profiles for the finer jobs. Special contours and unique features for effective and safe removal of fine or delicate bezels and fascia. The Pry Tools will not scratch or mar fascia. It tackles finer jobs that the average tools are too big for. These tools are made from impact resistant high quality nylon. Each Pry-Tool within this six piece Fine-Kit (on the right side of the image is specially designed with an extra slim profile and unique shape for the delicate task of removing small or fine fascia trim and bezels of; dashboards, air vents, door panels, door locks, electronic seat controls, seat levers, center counsels, gear shifter, etc....Super Tools for Auto Interior Work! This 11 Piece Set of plastic pry pullers is perfect for working on those expensive panels on car interiors. It will also help work loosen plastic decorative inserts, door moldings and countless other pieces on todays modern and many vintage cars. This set has more features plus quality of this set is great. (stronger and more durable) than other being sold, making this a much better deal...THERE IS A HIGH DEMAND for these interior tools.







Click Here to Buy Tools



email:  toolstore@aol.com

Product Search

News

Events