VW TOOL NUMBERS

103  T-Wrench 17 mm
For loosening and tightening
 - crankcase bolts and nuts,
 - torsion arm link pin clamp bolts,
 - brake back plate bolts,
 - spring plate hub cover bolts,
 - body mounting bolts of VW Passenger Cars 

106 T-Wrench 10 mm
For loosening and tightening
 - oil pump nuts,
 - oil strainer nuts,
 - intake manifold or preheater pipe nuts and bolts,
 - oil cooler nuts,
 - crankcase bolts,
 - heating control linkage,
 - bolts for valve push rod guide plates,
 - bolts on fan housing,
 - bolts on fan housing halves
 
109 Box Wrench 10 mm
For loosening and tightening nuts on oil cooler 
 
 
110 Box Wrench 27/30 mm
For loosening and tightening cradle nuts on transmission and steering wheel center nut
 
112 Special Wrench 36 mm with guide plate
For loosening
 - flywheel gland nut - (guide plate prevents the wrench from slipping off the gland nut),
 - rear axle shaft nuts,
 - fan nut
 
112a Special Wrench 36 mm with guide plate
For loosening
 - flywheel gland nut - (guide plate prevents the wrench from slipping off the gland nut),
 - rear axle shaft nuts,
 - special nut on fan
 
113 Open End Wrenches 27 mm
For adjusting
 - front wheel bearings,
 - steering worm adjusting sleeve,
For holding the pulley on the generator (with the straight type wrench)

Hazet version
113a Open End Wrenches 32 mm
For adjusting front wheel bearings
 
113b Open End Wrenches 24 mm
For adjusting front wheel bearings

Hazet version
113t Open End Wrenches 32 mm
For adjusting front wheel bearings 
114 T-Wrench 8 mm, square socket
For loosening and tightening
 - gearshift rod coupling,
 - screws on selector forks in standard transmission
 
116 T-Wrench 13 mm
  
118 Torque Wrench, 6 mkg (43 lbs./ft.) max
For loosening and tightening
 - rod nut,
 - head nut
Used in conjunction with 14 mm and 17 mm sockets and keys VW 156 (8 mm) and VW 157 (10 mm) for Allen setscrews
 
118/30 Torque Wrench, 30 mkg (217 lbs./ft.) max
For loosening and tightening
 - drive pinion nut in conjunction with 32 mm socket VW 162,
 - flywheel gland nut in conjunction with the guide plate of VW 112,
 - rear axle shaft nut in conjunction with 36 mm socket VW 163a 

121b Piston ring tool
For removing and installing
 - piston rings 

122b Circlip Pliers
For removing and installing
 - piston pin circlips,
 - glove compartment lid lock,
 - circlips in governor 

123 Piston Ring Compressing Tool 75 mm dia.
For pistons from 75 to 76 diameter
 
123a Piston Ring Compressing Tool 77 mm dia.
For pistons from 77 to 78 diameter
 
123b Piston Ring Compressing Tool 83 mm dia.
For pistons from 83 to 84 diameter
 
123c Piston Ring Compressing Tool 85.5 mm dia.
For pistons from 85.5 to 86.5 diameter
 
124 Chisel (Peening)
For securing
 - connecting rod bolts,
 - clutch release lever special nut,
 - hexagon nut of driven gear and shaft
 
124a Chisel (Peening)
For securing
 - connecting rod bolts or engine nuts
 - clutch release lever special nut,
 - hexagon nut of driven gear and shaft,
 - clampage nut on the bearing tube 
126a Fuel Pump Wrench
For removing and installing fuel pump
 
126b Fuel Pump Wrench 13 mm
For loosening and tightening 13 mm mounting nuts of fuel pump
 
130 King Pin Pilot Drift 5.9 mm
For removing and installing king pins of VW Passenger Cars having lubrication passage 6.0 to 6.5 mm dia., if VW 400 and corresponding tool set are not available
 
130a King Pin Pilot Drift 7.9 mm
For removing and installing king pins of VW Passenger Cars having lubrication passage 8.0 to 8.5 mm dia., if VW 400 and corresponding tool set are not available
 
131 King Pin Bush Pilot Drift
For removing and installing king pin bushes of VW Passenger Cars, if VW 400 and corresponding tool set are not available
 
131a King Pin Bush Pilot Drift
For removing and installing
 - knuckle pin bushes of VW Transporters,
 - sector shaft bushes of VW Transporters,
 - steering lever shaft bush in Transporter steering gear case,
 - lower knuckle pin bush of VW Transporters


131t King Pin Bush Pilot Drift
For removing and replacing king pin bushes and steering arm shaft bushes of VW Transporters,
In conjunction with VW 400, VW 401, and VW 412 for removing and installing cam lever shaft bushes in steering gear case of VW Transporters,
In conjunction with VW 400, VW 401, and VW 410 for removing upper pivot pin bush of VW Transporters,
In conjunction with VW 400, VW 401, and VW 421 for removing lower pivot pin bush of VW Transporters (VW 421 to be inserted in Press arbor) 
133 Torsion Arm Link Pin Bush Pilot Drift
For removing and installing torsion arm link pin bushes of VW Passenger Cars, if VW 400 and corresponding tool set are not available
 
133a Torsion Arm Link Pin Bush Pilot Drift
For removing and installing torsion arm link pin bushes
 
133b Torsion Arm Link Pin Drift
For removing and installing outer needle bearing rings of torsion arm link pins
 
133t Torsion Arm Link Pin Bush Pilot Drift
For removing and replacing torsion arm link pin bushes of VW Transporters 
136 Brake Lining Wear Checking Tool
For checking the brake lining thickness of disc brakes 
150 Offset Handle
For loosening and tightening socket-head screws of front torsion bar center locks (up to Chassis No. 1 397 022) in conjunction with key VW 156
 
151 T-Handle
With VW 156 for releasing and tightening front torsion bar center lock screws (front axle removed) and connecting rod bolts (old type). With VW 157 for releasing cylinder head nuts. Also used in conjunction with other sockets 
156 Key 8 mm
For loosening and tightening
 - socket-head screws of front torsion bar center locks (up to Chassis No. 1 397 022)
 - connecting rod bolts having 8 mm socket (earlier type)
 
157 Key 10 mm
For loosening and tightening cylinder head nuts
 
158 Double Offset Wrench 10 x 14 mm
For loosening and tightening the carburetor flange stud nuts
 
159 Oil Pressure Switch Wrench
For removing and installing oil pressure switch
 
159a Oil Pressure Switch Wrench 24 mm
For removing and installing 24 mm hex oil pressure switch 
161a Circlip Pliers
For removing and installing
 - circlip on crankshaft,
 - circlip on drive pinion,
 - circlip on hand brake lever pin,
 - double row ball bearing retaining ring on drive pinion,
 - circlip on rear axle shaft
 - distributor drive gear lock ring
 - lock ring on main drive shaft
 - circlip on commutator side end plate of VW starter motor
For removing retaining ring on rear drive shaft
 
162 Socket 32 mm
For tightening drive pinion nut in conjunction with VW 118/30 
163a Socket 36 mm
For tightening
 - flywheel gland nut,
 - rear axle shaft nuts 
164 Double Box Wrench 19 mm
For loosening and tightening rear shock absorber mounting bolts of VW Transporters up to Chassis No. 20-117 901 
165 Socket Wrench for Cylinder Head Nuts
For loosening and tightening 15 mm cylinder head nuts
 
170 Socket
For loosening and tightening
 - threaded ring in oil filler
 - threaded ring in oil breather
 
171 Spring Clip
For holding the cam followers in position while disassembling or assembling the engine
 
172 Drain Plug Key 17 mm Socket
For loosening and tightening
 - oil drain plugs in transmission case
 - oil drain plugs in reduction gear case
 
173 Special Socket
For loosening and tightening the gland nut with the automatic clutch in situ
 
174 Special Socket Wrench M 6
For loosening and tightening the socket head screws on the automatic clutch 
175 Special Pliers
For removing and installing the hose clips on the warm air connecting pipe between the left heater junction box and the oil bath air cleaner 
176 Extractor for Fan
For extracting fan from crankshaft
 
177 Centering Sleeve for Fan Housing
For centering the front half of fan housing to the oil return thread on hub of fan
 
178 Special Wrench for Carburetor Mounting
For removing and tightening carburetor mounting nuts
 
179 Special Wrench 36 mm
For adjusting the camber by resetting the eccentric bush on upper torsion arm
 
 
180 Open End Wrench 46 mm
For screwing and unscrewing the threaded adaptor for heat exchanger on muffler 
181 Open End Spanner 42 mm
For holding the bolt for rubber stop when unscrewing or screwing up the upper securing nut of front shock absorber 
182 Special Wrench (automatic transmission)
For adjusting
 - ring gear
 - preload of the pinion bearing
 
183 C Wrench for Round Nut (automatic transmission)
For tightening up the round nut for the double tapered roller bearing to prescribed torque
For loosening the round nut for the double tapered roller bearing
 
184 Retainer for the Drive Plate (automatic transmission)
For holding the torque converter drive plate whilst loosening as well as tightening the gland nut up to the specified torque 
185 Plate for Pressing off the Hub of the Fan
For pressing off the hub of the fan from the crankshaft
 
190 Installing Tool for Crankshaft Seal
For installing the crankshaft seal in the crankshaft on the fan side
 
191 Installing Tool for Crankshaft Seal
For installing the crankshaft seal in the crankshaft on the flywheel side 
192 Drift Sleeve (Oil Seal - Converter/Automatic Transmission)
For driving the oil seal into the differential carrier 
193 Drift Sleeve (Oil Seal - Final Drive/Transmission-Diagonal arm axle)
For driving
 - oil seal into the side cover
 - oil seal into the adjusting ring 
194 Drift Sleeve (Oil Seal - Final Drive/Diagonal arm axle)
For driving
 - oil seal into the side cover
 - oil seal into the adjusting ring
 - oil seal into the adjusting ring (automatic stickshift) 
195 Drift (Oil Seal - Final Drive/Automatic Transmission)
For driving
 - oil seal into the final drive cover
 - oil seal into the rear axle housing

201 Oil Pump Extractor
For extracting the oil pump body with the engine removed or installed
 
202 Extractor
For various removal operations in conjunction with items numbered from VW 202a to VW 202t
 
202a Extractor Hooks
For removing
 - the crankshaft gears,
 - the ball bearing from the differential housing,
 - the rear axle shaft outer ball bearing 
202aT Extractor Hooks
In conjunction with VW 202 and VW202i, for removing the spacer for the inner front wheel bearing
In conjunction with VW 202 and VW202mT, for removing the inner front wheel bearing
 
202b Extractor Hooks
For removing
 - the bearing housing on rear axle tube of VW Passenger Cars,
 - the steering wheel from steering column of VW Transporters
 
202c Extractor Ring
For removing the brake drums
 
202d Extractor Hooks
For removing
 - the brake drums,
 - the steering drop arm,
 - the steering wheel
 
202f Thrust Pad
For removing the gears from the crankshaft
For extracting the inner ball bearings in the reduction gear case 
202h Distance Sleeve
For removing
 - the bearing housing on rear axle tube of VW Passenger Cars,
 - the reduction gear case of VW Transporters 
202i Thrust Pad
For removing
 - the front brake drums,
 - the spacer for inner front wheel bearing 
202k Thrust Pad
For removing
 - the reduction driven gear and shaft outer bearing,
 - the rear axle shaft inner bearing,
 - the steering wheel from the steering column 
202kT Thrust Pad
In conjunction with VW 241T for removing the outer ball bearing of reduction gear shaft in reduction gear case and inner ball bearing of rear axle shaft while in the reduction box housing 
202m Thrust Pad
For removing
 - the front brake drums,
 - the spacer for inner front wheel bearing 
202mT Thrust Pad
In conjunction with VW 202, VW 202c, and VW 202d for removing the front brake drums on the VW Transporter
In conjunction with VW 202 and VW 202aT for removing the spacer for the inner front wheel bearing on VW Transporters 
202n Extractor Plate
For removing the reduction gear case of VW Transporters 
202nT Extractor Plate
In conjunction with VW 202, VW 202d, and VW 202h, for removing the inner half of reduction gear case of VW Transporters
 
202p Extractor Plates
For removing the steering wheel from the steering column (1 set comprises 2 cross plates, 2 extractor hook sockets, 4 bolts M 10 x 45 and 4 nuts M 10)
 
202pT Cross Plates
In conjunction with VW 202, VW 202b, or removing the steeand VW 202i for removing steering wheel from the steering column tube of VW Transporters. (1 set comprises 2 cross plates, 2 extractor hook sockets, 4 bolts M 10 x 45 and 4 nuts M 10) 
202s Extractor Hooks
For removing the spacer for the inner front wheel bearing
 
202t Thrust Pad
For removing the front brake drums 
202u Extractor Hooks
For pulling the roller bearing off the reduction gear driven gear and shaft
 
203b Fan Pulley Extractor
For removing the crankshaft pulley with engine removed or in situ
 
203b/1 Extractor Hooks for Industrial Motor
In conjunction with VW 203b and VW 203b/2, for removing fan pulley from crankshaft with engine removed or in situ 
203b/2 Thrust Pad for Industrial Motor
In conjunction with VW 203b and VW 203b/1, for removing fan pulley from crankshaft with engine removed or in situ 
203c Fan Pulley Extractor Hooks
For removing crankshaft fan pulley of VW Industry Motors 
203d Fan Pulley Thrust Pad
For removing the crankshaft pulley with engine removed or in situ 
204 Crankshaft Oil Seal Installing Tool
For installing crankshaft oil seal in crankcase 
204b Crankshaft Oil Seal Installing Tool
For installing crankshaft oil seal in crankcase
 
205 Electric Piston Heating Tool
For heating piston to about 80C (176F) for removal and replacement 
205a Electric Piston Heating Tool 75-78 mm dia.
For heating piston to about 80C (176F) for removal and installation of piston pin 
206 Template for Ignition Timing Notch
For marking out the notch for the ignition firing point on the pulley which has been supplied as a spare part


207 Piston Pin Pilot Drift
For removing or installing piston pin after having heated the piston
 
207a Piston Pin Removing and Installing Tool
For removing and installing piston pin after having heated the piston by means of the tool VW 205a 
207b Piston Pin Removing Tool
For removing the piston pin 
207c Piston Pin Drift
For pressing out the piston pin 
212a Piston Pin Bearing (little end) Removing and Installing Tool
For removing and installing piston pin bearings, especially with crankshaft installed 
210 Checking Appliance for V Belt Tension
For checking the V Belt tension 
214 Device for Checking, Straightening and Reaming Connecting Rods
For checking and straightening removed connecting rods
For reaming newly installed piston pin bearings (little end)
For checking parallelism between piston pin bearing (little end) and big end bearings 
214b Device for Checking, Straightening and Reaming Connecting Rods
For checking and straightening removed connecting rods
For reaming newly installed piston pin bearings (little end)
For checking parallelism between piston pin bearing (little end) and big end bearings
 
 
214c Supplement to Device for Checking, Straightening and Reaming Connecting Rods
For checking and straightening removed connecting rods
For reaming newly installed piston pin bearings (little end)
For checking parallelism between piston pin bearing (little end) and big end bearings
All work is carried out with the use of the base plate, bar and gauge from VW 214b 
 
214f Connecting Rod Checking, Straightening and Reaming Device
For checking and straightening removed connecting rods
For reaming newly installed piston pin bushes (little end)
For checking parallelism between piston pin bearing (little end) and big end bearing 
214f/18 Mandrel - Supplementry tool to device for checking and straightening connecting rods and reaming connecting rod bushes VW 214f (17 parts)
For checking and straightening the connecting rods
For reaming out new small end bushes after pressed in
For checking parallelism between big and small end bearings using the appropriate parts of appliance VW 214f 
214s/1 Device for Checking, Straightening and Reaming Connecting Rods
Used in connection with 214s/2
Clamp the devise in a vise. Remove piston pin bush before straightening.  Place connecting rod over locking lever (b) on the pin (a). Place the C-washer (c) in position and tighten lever to such an extent as to still allow the connecting rod to have sufficient play in both directions. The support (d) is released. Then insert pin (e) in little end bore, pressing it with two fingers toward the pin (a) so there is no tilt between pin (a) and connecting rod big end bearing nor between little end bore and pin (e). Check connecting rod for twist and parallelism by means of the gauge (f). If corrections are necessary, fully tighten locking lever (b) and straighten connecting rod by means of the mandrel. When the new piston pin bush has been fitted, insert reamer in the bush and hole provided in the bottom plate of the device, the guide bush ensuring a correct centering of the bush. Tighten both locking lever (b) and support (d) and ream the bush.  After this operation, recheck connecting rod for parallelism and twist as outlined above, but this time with the piston pin instead of the pin (e). Correct, if necessary, with a mandrel inserted in the piston pin. 
214s/2 Device for Checking, Straightening and Reaming Connecting Rods
Used in connection with 214s/1
Clamp the devise in a vise. Remove piston pin bush before straightening.  Place connecting rod over locking lever (b) on the pin (a). Place the C-washer (c) in position and tighten lever to such an extent as to still allow the connecting rod to have sufficient play in both directions. The support (d) is released. Then insert pin (e) in little end bore, pressing it with two fingers toward the pin (a) so there is no tilt between pin (a) and connecting rod big end bearing nor between little end bore and pin (e). Check connecting rod for twist and parallelism by means of the gauge (f). If corrections are necessary, fully tighten locking lever (b) and straighten connecting rod by means of the mandrel. When the new piston pin bush has been fitted, insert reamer in the bush and hole provided in the bottom plate of the device, the guide bush ensuring a correct centering of the bush. Tighten both locking lever (b) and support (d) and ream the bush.  After this operation, recheck connecting rod for parallelism and twist as outlined above, but this time with the piston pin instead of the pin (e). Correct, if necessary, with a mandrel inserted in the piston pin. 
215a Flywheel Retainer
For holding the flywheel when loosening and tightening the gland nut 
215b Flywheel Retainer
For holding the flywheel when loosening and tightening the gland nut, clutch bolts, and crankshaft pulley
 
215c Flywheel Retainer
For holding the flywheel with 130 teeth (outer dia. 276 mm) when loosening and tightening the gland nut, clutch bolts, and crankshaft pulley 
216 Flywheel Retainer (Industrial Engine)
For holding the radial toothed flywheel on the industrial engine when undoing or tightening the gland nut, as well as the bolts on the clutch and pulley 
217 Facing Cutter
For refacing
 - the torsion arm eyes,
 - the torsion arm eyes after exchanging the pilot with VW 217a (up to Chassis No. 1144302)
 
217/3T Facing Cutter Pilot
For refacing the torsion arm eyes in conjunction with the cutter and cross bar from VW 217 for VW Transporters 
217a Facing Cutter Pilot
For refacing the torsion arm eyes in conjunction with the cutter and cross bar from VW 217 (up to Chassis No. 1144302)
 
 
218 Gland Nut Bush Pilot Drift
For installing gland nut bush, if VW 400 and corresponding tool set are not available 
219 Clutch Pilot
For centering clutch plate during installation of clutch assembly 
222 Starter Shaft Bush Pilot Drift
For removing and installing starter shaft bush in transmission case, if VW 400 and corresponding tool set are not available
 
222a Starter Shaft Bush Pilot Drift
For removing and installing
 - starter shaft bush in transmission case
 - starter shaft bush in end plate, commutator side 
223 Knuckle Pin Extractor
For removing the upper knuckle pin of VW Transporters 
223a Knuckle Pin Extractor
For removing the upper knuckle pin of VW Transporters, if VW 400 and corresponding tool set are not available
 
223t King Pin Extractor
For removing upper king pin in the stub axle of VW Transporters. Place extractor on stub axle so thrust screw is in line with upper king pin 
224 King Pin Bush Reamer
For reaming up the king pin bushes (reamer with two guides, 35 mm long)
 
224a King Pin Bush Reamer
For reaming up
 - the king pin bushes
 - the sector shaft bushes
(reamer with two guides, 40 mm long)
  
224t King Pin Bush Reamer
For reaming up the king pin bushes and steering arm shaft of VW Transporters (21 - 24.5  with a 40 mm long guide) 
228a Starter Shaft Bush Extractor
For removing
 - the starter shaft bush in transmission case with the engine installed
 - the distributor drive pinion
 
 
228b Starter Shaft Bush Extractor
For removing the starter shaft bush in transmission case with the engine installed 
230 Rear Axle Shaft Oil Seal Installing Tool
For installing oil seal in rear axle bearing cover, if VW 400 and corresponding tool set are not available 
230a/3 Oil Seal Installing Gauge (Rear Axle)
For installing oil seal in rear axle bearing cover. Insert gauge in axle shaft bearing cover. Check square seating of oil seal by turning gauge in axle shaft bearing cover. 
231a Crankshaft Drill Jig
For drilling new dowel pin holes on flywheel end of crankshaft 
231b Flywheel Drill Jig
For drilling new dowel pin holes in flywheel 
231c Crankshaft Drill Jig
For drilling new dowel pin holes for the flywheel in 55 mm dia. crankshafts 
231d Flywheel Drill Jig
For drilling new dowel pin holes in flywheel for 55 mm dia. crankshafts 
235 Steering Wheel Puller
For pulling the steering wheel off the steering column (Type 2)
 
236 Drop Arm Puller
For pulling the drop arm off 
237 Puller for Ball Bearing
For pulling the ball bearing off the flange of the differential housing 
240a Drift
For installing
 - the reduction gear case on the rear axle tube,
 - the bearings housing on the rear axle tube,
 - the inner rear axle shaft ball bearing in the reduction gear case 
 
240t Driver
For driving
 - the inner half of reduction gear case on rear axle shaft tube,
 - the inner ball bearing on rear axle shaft,
 - the rear axle shaft bearing housing on tube 
241a Ball Bearing Extractor
For removing
 - reduction gear shaft outer ball bearing in reduction gear case cover of VW Transporters,
 - inner ball bearings in reduction gear case of VW Transporters,
 - rear axle shaft outer ball bearing in reduction gear case cover of VW Transporters,
 - rear wheel ball bearing of VW Passenger Cars  
241t Ball Bearing Extractor
In conjunction with VW 202kT, for removing
 - outer ball bearing of reduction gear shaft in outer half of reduction gear case
 - inner ball bearing of rear axle shaft in inner half of reduction gear case of VW Transporters
For removing rear wheel ball bearing
 
242 Ball Bearing Extractor
For removing reduction gear shaft inner ball bearing in reduction gear case of VW Transporters 
242t Ball Bearing Extractor
For removing reduction gear shaft inner ball bearing in reduction gear case 
243 Driver
For installing
 - the inner ball bearing of the driven gear and shaft in the reduction gear case,
 - the outer ball race of the inner front wheel bearing 72 mm dia. 
243t Driver
For installing
 - the inner ball bearing of the driven gear and shaft in the reduction gear case,
 - the outer ball race of the inner front wheel bearing 72 mm dia. 
244 Driving Sleeve
For installing
 - spacer for inner front wheel bearing,
 - inner ball race of outer wheel bearing
 
244b Driving Sleeve
For installing
 - the rear axle shaft outer ball bearing,
 - spacer for inner front wheel bearing,
 - inner ball race of outer front wheel bearing,
 - the oil seal for main drive shaft in transmission case 
 
244c Driving Sleeve
For installing the inner ball race of outer front wheel bearing
 
244d Driving Sleeve
For driving the roller bearing on to the driven gear and shaft 
244t Driving Sleeve
For driving
 - inner ball bearing on rear axle shaft in reduction gear case,
 - gears on rear axle shaft and reduction gear shaft,
 - spacer and outer front wheel bearing on front axle stub 
245a Protractor
For measuring
 - camber,
 - caster,
 - spring plate adjustment,
For checking level position of vehicle for carrying out above operations
 
(Brazilian 245)
246 Not-Go Plug Gauge
For checking
 - wear of starter shaft bush,
 - wear of gland nut bush
 
247 Master Ring Gauge
For setting internal dial gauge, measuring intermediate crankcase bore 
248 Mandrel for Installing and Removing the Governor Oil Seal (automatic transmissions)
For driving in and out the oil seal of the governor
For driving out the oil control sleeve
 
249 Clamping Piece (automatic transmissions)
For checking the friction torque of the double tapered roller bearings of the drive pinion and the differential when used in conjunction with a torque gauge
 

250 Alignment Gauge for Piston Rods (Installed)
For checking the alignment of the piston rods 
252a Master Ring Gauge 75 mm
For setting internal dial gauge for measuring cylinder bore 
252b Master Ring Gauge 75.5 mm
For setting internal dial gauge for measuring cylinder bore 
252c Master Ring Gauge 76 mm
For setting internal dial gauge for measuring cylinder bore 
252d Master Ring Gauge 77 mm
For setting internal dial gauge for measuring cylinder bore 
252e Master Ring Gauge 77.5 mm
For setting internal dial gauge for measuring cylinder bore 
252f Master Ring Gauge 78 mm
For setting internal dial gauge for measuring cylinder bore 
253 Valve Guide Plug Gauge
For measuring valve guides bores
 
254 Clutch Adjustment Dial Gauge
For checking adjustment of clutch release plate
 
254a Clutch Adjustment Gauge
For checking adjustment and parallelism of clutch release plate
 
254b Clutch Adjustment and Repair Appliance
For adjusting the clutch release ring (in conjuction with a flywheel)
For dismantling the clutch (in conjuction with a flywheel)
For assembling the clutch (in conjuction with a flywheel) 
256a Front Axle Tube Alignment Gauge
For checking front axle tube alignment
 
258 Stub Axle Gauge
For checking stub axle alignment of VW Passenger Cars up to Chassis No. 1-397 022 
258a Stub Axle Gauge
For checking stub axle of VW Passenger Cars from Chassis No. 1-397 023 for twist
 
258b Steering Knuckle Gauge
For checking steering knuckle of VW Transporters up to Chassis No. 20-117 901 for twist 
258c Steering Knuckle Gauge
For checking steering knuckle of VW Transporters from Chassis No. 20-117 902 for twist 
 
258d Steering Knuckle Pilot
For checking the steering knuckle for alignment 
258f Steering Knuckle Gauge
For checking the steering knuckles for twist


258h Steering Knuckle Gauge
For checking the steering arm on the steering knuckle for bends 
258k Measuring Device for Steering Knuckle
For checking
 - the stub axle for bends,
 - the contact surface for the caliper on the steering knuckle for distortion
 
258m Steering Knuckle Gauge
For checking the steering arm on the steering knuckle for twist 
258p Measuring Device for Steering Knuckle
For checking
 - the stub axle for bends,
 - the contact surface for the caliper on the steering knuckle for distortion 
258t Stub Axle Gauge
For checking stub axle of VW Transporters for twist and bend
 
259 Torsion Arm Link Gauge
For measuring
 - the torsion arm link offset,
 - the wear of contact faces for torsion arm link pin shims 
260 Piston Pin Bushes Reamer (with Reamer 19.5 - 21.5 mm)
For reaming the piston pin bushes with the connecting rods installed
Upper picture - arrangement for cyl. 1+3
Lower picture - arrangement for cyl. 2+4 
261 Protractor
For measuring
 - the alignment of the front axle beam,
 - the adjustment of the lower torsion arm,
 - the camber,
 - caster,
 - spring plate adjustment
For checking level position of vehicle for carrying out above operations
 
262 Device for Checking Steering Arm
For checking the steering arm for twist and wear
 
266f Tie Rod End Remover
For removing tie rod ends 
266h Tie Rod End Remover
For removing all maintenance free type tie rod ends 
267 Ball Joint Removal Tool
For pressing out
 - lower ball joint from the steering knuckle after the cap nut has been fitted
 - upper ball joint from the steering knuckle after the cap nut has been fitted
For pressing off the eccentric bush from the upper ball joint
 
267a Ball Joint Removal Tool
For pressing out
 - lower ball joint from the steering knuckle after the special nut has been fitted
 - upper ball joint from the steering knuckle after the special nut has been fitted
For pressing off the eccentric bush from the upper ball joint after the special nut has been fitted 
270a Torsion Arm Offset Gauge
For checking offset between upper and lower torsion arms of VW Passenger Cars
 
270b Torsion Arm Offset Gauge
For checking offset between upper and lower torsion arms of VW Transporters
 
270c Torsion Arm Offset Gauge
For measuring offset between upper and lower torsion arms of VW Transporters 
270t Torsion Arm Offset Gauge
For checking offset between upper and lower torsion arms of VW Transporters
 
271 Assembly and Checking Device for the Roller Steering Gear of the VW 1302
For carrying out assembly work on the steering gear of VW 1302
For adjusting the steering of VW 1302 
272 Torsion Arm Bushes Extractor
For removing the torsion arm bushes from front axle tubes 
272t Torsion Arm Bushes Extractor
For removing the torsion arm bushes from front axle tubes on VW Transporters 
273a Torsion Arm Bush Drift
For installing the torsion arm bushes and needle bearings in front axle beams in VW Passenger Cars 
273b Torsion Arm Bush Drift
For installing the torsion arm bushes in the front axle beams in VW Transporters 
273c Lower Torsion Arm Bush Drift
For installing the lower torsion arm bushes and lower needle bearings in front axle beam in VW Type 3s
 
273d Upper Torsion Arm Bush Drift
For installing the upper torsion arm bushes and upper needle bearings in the axle beam in VW Type 3s 
273t Torsion Arm Bush Drift
For installing the torsion arm bushes in the front axle beams in VW Transporters 
274a Torsion Arm Bush Reamer
For reaming up the torsion arm bushes in VW Passenger Cars 
274b Torsion Arm Bush Reamer
For reaming up the torsion arm bushes in VW Transporters
 
274c Cutter for Torsion Arm Bushes
For cutting the upper and lower torsion arm bushes in the front axle beams in VW Type 3s 
274t Torsion Arm Bush Reamer
For reaming up the torsion arm bushes in VW Transporters 
275 Steering Damper Installing Tool
For holding steering damper when having it compressed in a vice for installing it to the steering knuckle of Transporters up to Chassis No. 20-117 901 
275t Steering Damper Installing Tool
For holding steering damper when having it pressed together in a vise for fitting it to the stub axle in VW Transporters 
276a Lower Torsion Arm Extractor
For removing the lower torsion arm from the front axle beam in VW Type 3s
 
 
277 Open End Wrench 41 mm
For loosening and tightening the steering worm adjusting screw lock nut
 
277a Open End Wrench 50 mm
For loosening and tightening the lock nut of the adjustment screw of the worm spindle of the roller steering of VW 1302
 
278 Wrench for transmission plug 
278a Wrench for Steering Worm Adjustment
For adjusting the steering worm in the roller type steering
 
278b Adjustment Socket (Axial play/Steering worm)
For adjusting
 - the axial play of the steering worm in the roller type steering with the 24 mm hexagon (Type 1 and 3),
 - the axial play of the steering worm in the circulating ball steering with the 24 mm hexagon (Type 4),
 - the axial play of the steering worm in the roller type steering with the 30 mm hexagon (RHD Type 1 from August 1970)
 
279 Steering Adjustment Device
For checking and setting the free of play steering lock of the roller type steering
 
279a Appliance for Checking the Steering
For setting the central position of the steering gear for the purpose of measuring and correcting the track angle
 
280 Assembly and Test Jig for Roller Steering
For assembly work on the steering gear
For adjusting the steering 
281a Hinged Lever for Checking the Ball Joints
For checking the play of the ball joints 
282b Torsion Arm Test Plate
For checking the torsion arms for parallelism and twist
 
282d Torsion Arm Test Plate
For checking the upper and lower torsion arms for distortion
 
284 Circlip Installing Tool
For installing the circlips for the synchronizer hub of 3rd and 4th gear (Type 2) 
285 Dial Gauge for Ball Bearing Seating
Place the base (b) of the bridge (a) on the transmission case jointing face so the centering piece (c) enters the inner ring of the ball bearing. Rotate the tracer of the contact block (d) once around the outer ring of the ball bearing by means of the knurled hand wheel situated below the tracer of the dial indicator. A tilted position of the ball bearing will be indicated by the deflecting needle 
287 Differential Housing Gauge
For measuring
 - differential housing length,
 - distance from face of differential housing to plain face of ring gear (crown wheel)
 
287a Differential Housing Gauge
For measuring the length of the differential housing in conjunction with the tracer pin of VW 299
 
288b Backlash Gauge
For measuring backlash between drive pinion and ring gear (crown wheel)
 
288c Backlash Gauge
For measuring backlash between drive pinion and ring gear (crown wheel) 
289b Transmission Case Mandrel
For measuring
 - depth of transmission case,
 - adjustment of drive pinion to determine thickness of shims
 
289d Transmission Case Mandrel
For adjusting the drive pinion
For measuring the depth of transmission case between the differential bearings in conjunction with the dial gauge bracket from VW 297 
290a Ball Bearing Installing Tool
For installing differential ball bearings in transmission case, if VW 400 and the corresponding tool set are not available 
290b Ball Bearing Removing Tool
For removing differential ball bearings in transmission case, if VW 400 and the corresponding tool set are not available 
291a Main Drive Shaft Oil Seal Cutter
For cutting recess for main drive shaft oil seal in transmission case (Only used for unfinished transmission cases) 
291b Main Drive Shaft Oil Seal Installing Tool
For installing oil seal on main drive shaft 
292 Crankshaft End Play Gauge
For checking
 - the crankshaft end play,
 - the end play of the oil pump gears,
 - the rock on contact breaker plate in the distributor
 
293 Drive Pinion Holding Pinion
For loosening and tightening the round nut on the drive pinion
 
294 Gearshift Test Appliance
For adjusting the selector forks
 
294b Appliance for Adjustment of the Shift Forks
For adjusting shift forks 
295 Needle Bearing Drift
For removing and installing the needle bearing on the reserve gear shaft 
295a Additional Tool for Drift VW 295
For removing and installing the needle bearing for the main drive shaft in conjunction with VW 295
 
296 Transmission Removal Tool
For removing the transmission from the transmission case
 
297 Ring Gear Adjusting Device
For adjusting the ring gear to its prescribed backlash
For various operations on the transmission
 
298 Gauge Ring
For adjusting the ring gear (crown wheel)
 
299 Adjusting Device for Concaved Washer
For determining the thickness of the shims of the drive pinion concave washer 
 
307 Fixture
For holding
 - the engine during assembly and disassembly in conjunction with VW 313 and assembly stand,
 - the transmission with rear axle during assembly and disassembly in conjunction with VW 313 and an assembly stand
 
307a Support
For holding
 - the engine during assembly and disassembly in conjunction with VW 313 and assembly stand,
 - the transmission with rear axle during assembly and disassembly in conjunction with VW 313 and an assembly stand 
308 Stand
For holding
 - fixture VW 307 during assembly and disassembly of engine,
 - fixture VW 307 during assembly and disassembly of transmission,
 - holder VW 309 during assembly and disassembly of front axle 
309 Holding Plate
For holding the front axle during assembly and disassembly in conjunction with VW 313 and an assembly stand
 
309a Front Axle Adaptors
For holding the front axle during assembly and disassembly in conjunction with VW 309 
 
309b Clamps for Front Axle
For clamping the front axle during assembly and disassembly in conjunction with VW 309 
309c Support (4 parts)
For holding the front axle during assembly in conjunction with VW 309, VW 313 and an assembly stand 
310 Fixture
For holding crankshaft 
310a Fixture
For holding crankshaft 
311 Valve Extractor
For removing and installing valves 
311a Cutter for Valve Seat with Pilot (45 deg.)
For re-facing valve seats 
311b Valve Grinding Kit
For checking valve guides and valve seats,
For reaming up valve guides,
For refacing valve seats,
For remachining and cleaning combustion chambers in cylinder head 
311c Chuck
For holding the valve when grinding in 
311d Cutter for Valve Seat with Pilot (15 and 75 deg.)
For correcting valve seat angles 
311f Chuck
For holding the 8 mm dia. valve when grinding in 
311h Valve Extractor
For removing and installing the valves
 
311k Valve Grinding Kit
For checking valve guides and valve seats,
For reaming up valve guides,
For refacing valve seats,
For remachining and cleaning combustion chambers in cylinder head
 
311s Valve Spring Compressing Tool
For compressing the valve spring when removing or installing the valve cotters (when engine is installed, with the aid of the compressed air line from VW 653/2) 
313 Fixture
For holding
 - fixture VW 307 during assembly and disassembly of engine,
 - fixture VW 307 during assembly and disassembly of transmission,
 - the holding plate VW 309 during assembly and disassembly of front axle
 
314 Fixture
For tightening and loosening the nut on the drive pinion
For holding the differential housing during assembly and disassembly: Type 1 (up to Chassis No. 3 192 506); Type 2 (up to Chassis No. 469 505)
 
327a Float Needle Valve Gauge
For checking the float needle valve length, (up to Chassis No. 1-397 022) 
327b Carburetor Air Correction Jet Height Gauge
Remove venturi. Place gauge on jointing face of carburetor bowl, at the same time inserting the guide pin in the outlet hole of the spraying well. The distance from the outlet bore to the jointing face may vary within a range of .4 mm.
For use with VWs up to Chassis No. 1-397 022 
328a Fuel Pump Push Rod Gauge
For adjusting fuel pump stroke with fuel pump installed


328b Fuel Pump Diaphragm Gauge
For installing the fuel pump diaphragm: Type 1 (up to Chassis No. 3 192 506); Type 2 (up to Chassis No. 469 505)


328c Fuel Pump Push Rod Gauge
For adjusting fuel pump stroke with vertical drive fuel pump installed


328d Fuel Pump Diaphragm Gauge
For adjusting the diaphragm of the vertical drive type fuel pump


330 Clamping and Measuring Plates for Limited Slip Differential
For clamping the partially assembled limited slip differential for the purpose of measuring 
340 Tensioning Device for Coil Springs
For tensioning the coil springs of the suspension struts when removing or installing 
341c Toe-In Gauge
For checking the toe-in of the front wheels 
342 Timing Light
For setting the timing, testing operation of advance mechanism 
350 Retaining Plate with Measuring Equipment (automatic transmission)
For holding the final drive for assembly and for adjusting the ring gear
 
351 Holding Appliance for Rear Axle and Transmission (automatic transmission)
For holding the rear axle and the transmission when carrying out assembly work 
352 Support for Transmission
For supporting the transmission during assembly used in conjunction with VW 309, VW 313 and an assembly stand
 
353 Support for Transmission
For supporting the transmission whilst carrying out dismantling and assembly work in conjunction with VW 309, VW 313 and an assembly stand 
360 Measuring Rod for Rear Axle
For checking the spacing of the rear wheel shafts, taken at the center of the transmission unit 
361 Checking Appliance for Rear Axle (3 parts)
For checking the spacing of the rear wheel shafts, taken at the center of the transmission unit 
380 Ring Gear Adjustment Appliance (4 parts)(automatic transmission)
For adjusting the ring gear and drive pinion (Type 3) 
380 Bridge Piece for Final Drive (automatic transmission)
For adjusting the ring gear in conjunction with VW 350 (Type 3) 
381 Ring Gear Adjustment Appliance (15 parts)
For adjusting the ring gear and drive pinion (Type 2) 
382 Transmission Case Mandrel (10 parts)(automatic transmission)
For adjusting the ring gear and drive pinion (Type 1)
 
382 Ring Gear Adjusting Appliance (7 parts)(automatic transmission)
For adjusting the ring gear (Type 1) 
383 Measuring Appliance for Final Drive (9 parts)
For adjustment of ring gear and drive pinion used in conjunction with VW 249, VW 381/1, VW 382/3, VW 382/6, VW 382/7 and VW 382/8 
383 Ring Gear Adjusting Appliance (6 parts)
For adjusting the ring gear in conjunction with VW 249, VW 382/3, VW 382/6, VW 382/7 and VW 382/8 (Type 4) 
384 Adjustment Appliance for Rear Axle
For adjustment of the rear gear and drive pinion used in conjunction with VW 382 
385 Universal Mandrel (20 parts) for Pinion Adjustment
For adjusting the pinion


387 Universal Dial Gauge Bracket
For adjusting the ring gear


390 Measuring Appliance for Manual Transmission
For adjusting the gear sets on the main shaft 
391 Drive Flange Fitting Appliance
For removing and installing
- the drive flange from the final drive
Dismantling
- the gear box


>Help!  >Donate  >Buy Shirts!  >Register  >Control Panel  >Log in 
See all Samba banner ads | Advertise on TheSamba.com
 
Home Classifieds Gallery Forums Community Archives Technical
      
Manuals   |   VIN Numbers   |   M-Codes   |   Wiring   |   Paint/Upholstery   |   Information   |   Dictionary 
400 Repair Press 15 Ton
For pressing operations in conjunction with the tools from VW 401 to VW 449b 
401 Thrust Plate
For carrying out the many press operations in conjunction with the tools from VW 405 etc.
 
402 Thrust Plate
For removing and installing
 - the roller bearing on the drive pinion,
 - the ball bearing on the drive pinion
For removing
 - the crankshaft timing gear and spacer ring, the distributor drive gear,
 - the rear ball bearing on the main drive shaft,
 - the clutch gear  for 1st and 2nd speed from the drive pinion,
 - the rear axle shaft bearing housing,
 - the upper ball joint from the eccentric bush of the steering knuckle,
 - the lock ring of the distributor drive gear
For installing
 - the piston pin bushes,
 - the ball joint in the upper and lower torsion arm 
405 Punch with V-Block
For straightening in conjunction with VW 406 
406 V-Block (two)
For straightening in conjunction with VW 405
For pressing the differential bearings out of the transmission case 
407 Punch
For removing and installing
 - the axle shaft bearing housing,
 - the reduction gear case
For removing
 - the crankshaft timing gear and spacer ring,
 - the distributor drive gear
For pressing
 - out the 52 mm dia. outer front wheel bearing,
 - in and out the 48 mm dia. outer front wheel bearing,
 - the reduction gear case on to the axle tube,
 - in the piston pin bushes,
 - in the ball joints in the lower torsion arm 
408 Punch
For removing and installing
 - the torsion arm link pin bushes,
 - the starter shaft bush,
 - the bush for the clutch pedal,
 - the bush for the brake pedal,
 - the oil seal for the rear wheel bearing,
 - the differential housing bearings
For removing
 - the torsion bar from the spring plate,
 - the main drive shaft bearing from the great carrier,
 - the armature ball bearing on the commutator side,
 - the generator and plate, fan side,
 - the generator and plate, drive side,
 - the 4th gear and the needle bearing inner race of the drive pinion,
 - the double ball bearing of the drive pinion,
 - the upper ball joint from the eccentric bush of the steering knuckle
For installing the piston pin bush 
408a Punch
For removing and installing
 - the torsion arm link pin bushes,
 - the starter shaft bush,
 - the bush for the clutch pedal,
 - the bush for the brake pedal,
 - the bearing ring for the round nut (drive pinion),
 - the bearing outer race in the final drive carrier,
 - the bearing bush for the 4th and reverse clutch,
 - the outer race for the tapered roller bearing in bearing ring,
 - the oil seal for bearing cover,
 - the pedal bushes,
 - the seal for the bearing ring,
 - the bearing ring out of the bearing tube,
 - the bearing outer race in the cover of the bearing tube,
 - the gear wheel and inner race for needle bearing/drive pinion,
 - the seal on the final drive cover,
 - the tapered roller bearing outer race
For pressing out and installing
 - the oil seal for the rear wheel bearing,
 - the ball bearing for the differential
For pressing out
 - the torsion bar from the spring plate,
 - the ball bearing for the drive shaft out of the gear carrier,
 - the bearing in the gear carrier,
 - the constant velocity joint,
 - the center tie rod out of the drop arm,
 - the side tie rod out of the center tie rod
For pressing off
 - the ball bearing from the generator armature on the commutator side,
 - the end plate from the generator armature on the fan side,
 - the gear wheel for the 4th gear and the needle bearing inner race from the drive pinion,
 - the double ball bearing out of the pinion,
 - the upper torsion arm from the eccentric bush for the steering knuckle,
 - the bearing inner race from the pinion,
 - the constant velocity joints,
 - the tapered roller bearing from the cover (differential),
 - the ball bearing from the drive gear,
 - the bearing inner race from the main shaft,
 - the tapered roller bearing - inner race
For pressing on the inner race of the double tapered roller bearing for the drive pinion
For pressing in
 - the small end bush,
 - the oil seal in bearing cover


 
409 Punch
For removing and installing
 - the ball bearings in right hand on left hand transmission case halves,
 - the torsion arm link pin bushes in upper and lower king pins
For removing
 - the reverse sliding gear bush,
 - the drive pinion tapered bearing,
 - the 3rd gear on the main drive shaft of synchromesh transmission
For installing
 - the inner 59 mm dia. front wheel bearing,
 - the outer race of the inner 72 mm dia. front wheel bearing,
 - the upper and lower king pins,
 - bushes for the brake pedal,
 - the bush for the clutch pedal shaft,
 - the bush for the clutch pedal,
 - the generator end plate on the fan side,
 - the armature bearing, commutator side 
410 Punch
For pressing in the bushes for the clutch pedal shaft
For removing and installing
 - the bush in shock absorber in steering damper eye,
 - the gland nut bush
For removing
 - the reverse sliding gear bush of synchromesh transmission,
 - the inner race of the inner front wheel bearing,
 - the inner race of the outer front wheel bearing
For pressing out
 - the bush for the upper king pin,
 - the piston pin bush,
 - the bearing tube for the brake pedal,
 - the clutch pedal shaft from the clutch pedal,
 - the ball joint from the lower torsion arm 
411 Punch
For removing and installing
 - the king pin,
 - the clutch operating shaft bushes,
 - the king bushes,
 - the bush in the starter end plate, commutator side
For removing
 - the clutch pedal shaft bush,
 - the torsion arm link pin bushes from upper and lower king pins,
 - the drive pinion roller bearing inner race,
 - the ball bearing and the needle bearing inner race for the 1st gear on the drive pinion,
 - the clutch gear and the needle bearing inner race for the 4th gear from the main drive shaft,
 - the ball joint from the lower torsion arm (push the bolt out as far as possible)
For installing
 - the drive pinion roller bearing inner race,
 - the outer 52 mm dia. front wheel bearing,
 - the outer ball race of the 62 mm dia. outer front wheel bearing 
412 Thrust Disc
For carrying out a number of operations in conjunction with VW 401 and other press tools 
415 Tube 57 mm dia.
For removing and installing the left and right ball bearings in transmission case
For pressing
 - the ball joint with eccentric bush for the steering knuckle out of the upper torsion arm,
 - the ball joint out of the lower torsion arm
For removing
 - the distributor drive gear,
 - the crankshaft timing gear, spacer and distributor drive gear,
 - the distributor drive gear retaining ring
For installing
 - the brake pedal bushes,
 - the inner 59 mm dia. front wheel bearing and the oil seal,
 - the bushes for the brake pedal shaft,
 - the ball joint in the upper torsion arm
For adjusting the concaved washer of the drive pinion 
415a Tube 60 mm dia.
For removing and installing the left and right ball bearings in transmission case
For pressing
 - the ball joint with eccentric bush for the steering knuckle out of the upper torsion arm,
 - the ball joint out of the lower torsion arm
For removing
 - the distributor drive gear,
 - the crankshaft timing gear, spacer and distributor drive gear,
 - the distributor drive gear retaining ring
For installing
 - the brake pedal bushes,
 - the inner 59 mm dia. front wheel bearing and the oil seal,
 - the bushes for the brake pedal shaft,
 - the ball joint in the upper torsion arm
For adjusting the concaved washer of the drive pinion 
416 Tube 38 mm dia.
For installing the drive pinion double ball bearing
For pressing out the clutch pedal shaft bushes 
416a Tube 38 mm dia.
For installing the double ball bearing for the pinion
For pressing out the clutch pedal shaft bushes
For pressing in the oil control sleeve
For pressing off the tapered roller bearing from the differential housing 
416b Tube 37 mm dia.
For installing the double ball bearing for the pinion
For pressing out the clutch pedal shaft bush
For pressing in
 - the oil control sleeve,
 - the bonded rubber mounting for the steering idler arm bracket
For pressing off the tapered roller bearing from the differential housing
For pressing out the piston pin bush
For pressing on
 - the constant velocity joint,
 - the tapered roller bearing (differential cover)
For pressing out and pressing in the bushes for the foot pedal
For pressing on and pressing off the bearer ring (differential housing) and cover
 
417 Tube 30/31.9 mm dia.
For installing the steering worm 16.8 mm dia. lower thrust bearing 
418 Tube 32.5 mm dia.
For removing and installing the starter motor shaft bush in the end plate on the commutator side
For removing the king pin
For installing the torsion arm link pin bush 
418a Tube 31.5 mm dia.
For removing and installing the starter motor shaft bush in the end plate on the commutator side
For pressing out
 - the king pins,
 - the ball joint from the lower torsion arm
For pressing in
 - the torsion arm link pin bushes,
 - piston pin bush
For pulling out the sliding reverse gear shaft
For pressing on the tapered roller bearing (differential housing cover) 
419 Tube 32 mm dia.
For removing
 - the gland nut bush,
 - the reverse sliding gear bush of transmission,
 - the piston pin bush,
 - the ball joint with the eccentric bush for the steering knuckle out of the upper torsion arm
For installing
 - the main drive shaft bearings,
 - the clutch gear for 3rd and 4th gear on the main drive shaft,
 - the needle bearing inner race for the 4th gear on the main drive shaft 
420 Tube 28 mm dia. (210 mm long)
For removing and installing the reverse sliding gear bush
For installing
 - the drive pinion roller bearing,
 - the 4th gear on main drive shaft,
 - the main drive shaft front bearing,
 - the 62 mm dia. outer front wheel bearing 
421 Tube 28 mm dia. (100 mm long)
For removing and installing
 - the lower king pin bush,
 - the shock absorber eye bush and the steering damper bush
For removing the 3rd gear from main drive shaft of the synchromesh transmission
For installing
 - the clutch pedal shaft bushes,
 - the ball bearing on the commutator side of the generator armature,
 - the end plate of the generator armature on the drive side 
422 Tube 28 mm dia. (split)
For removing the king pin bush
For installing
 - the 4th gear and needle bearing inner race on the drive pinion,
 - the drive pinion and main drive shaft in the gear carrier,
 - the piston pin bush 
423 Tube 21.5 mm dia.
For removing
 - the king pin bushes,
 - the piston pin bush
For installing the steering worm 16.8 mm dia. upper thrust bearing 
426 Tube 32 mm dia., 45 mm long
For pressing
 - the circlip onto the drive shaft
 - the drive shaft into the ball bearing in the gear carrier 
427 Guide Tube
For guiding
 - the crankshaft timing gear, spacer and distributor drive gear, when pressing them into position,
 - the distributor drive gear when pressing it into position 
428 Guide Tube, tapered
For guiding the distributor drive gear retaining ring when pressing it into position 
428a Guide Tube, tapered
For guiding
 - the distributor drive gear retaining ring when pressing it into position,
 - the crankshaft timing gear, spacer and distributor drive gear, when pressing them into position,
 - the distributor drive gear when pressing it into position 
429 Thrust Ring
For installing
 - the distributor drive gear retaining ring,
 - the ball joint in the upper torsion arm 
430 Thrust Pad (bronze)
For installing
 - the drive pinion roller bearing,
 - the drive pinion roller bearing inner race,
 - the ball bearing and needle bearing inner race for 1st gear on the drive pinion,
 - the piston pin bush 
431 Thrust Pad 16.5/28 mm dia.
For removing
 - the 3rd gear on main drive of synchromesh transmission,
 - the ball joint from the lower torsion arm (push the bolt out as far as possible)
For installing
 - the torsion arm link bush,
 - the brake pedal bush,
 - the clutch pedal bushes 
432 Arbor 50 mm dia.
For installing
 - the outer front wheel outer ball race (52 mm dia.),
 - the king pin bushes,
 - the gland nut bush,
 - the outer race of the inner front wheel bearing,
 - the outer race of the outer front wheel bearing,
 - the axle shaft bearing housing,
 - the clutch pedal bushes,
 - the ball joint in the upper torsion arm 
433 Thrust Pad
For removing and installing
 - the differential bearings in transmission case,
 - the main shaft bearing in the gear carrier
For pressing out the rear wheel bearing oil seal
For installing
 - the rear axle shaft bearing housing on axle tube (approx. up to Chassis No. 1 637 000),
 - the outer race of the 62 mm dia. outer front wheel bearing,
 - the bushes for the front brake shaft,
 - the outer races of inner front wheel bearings with 59 mm and 62 mm dia. and also the oil seal,
 - the bushes for the brake pedal,
 - the ball joints in the upper torsion arm,
 - the ball joints in the lower torsion arm 
433a Spacer Ring
For installing the rear axle shaft bearing housing on the axle tube (approx. up to Chassis No. 1 637 000) 
434 Arbor
For removing
 - the torsion arm link pin bushes,
 - the drive pinion and main drive shaft from the gear carrier
For installing
 - the king pins,
 - the gland nut bush,
 - the main drive shaft bearing in the gear carrier 
435 Arbor
For removing and installing
 - the clutch operating shaft bushes in transmission case,
 - the clutch pedal bush,
 - the brake pedal bush
For removing
 - the clutch gear and needle bearing inner race for 4th gear from the main drive shaft,
 - the clutch pedal shaft bush 
436 Guide Pin, tapered
For pressing out the clutch pedal shaft
For installing the telescopic shock absorber bush 
436a Guide Pin, tapered
For pressing out the clutch pedal shaft
For pressing in the metal sleeve of the rubber bush of the telescopic shock absorber 
437 Guide Pin, tapered
For installing
 - the lever type shock absorber and steering damper eye bushes,
 - the bushes for the accelerator pedal shaft 
437a Guide Pin, conical
For pressing in
 - the metal sleeve of the rubber bush of the shock absorbers and steering dampers,
 - the bushes for the accelerator shaft 
438 Guide Pin, cylindrical
For removing the bushes in both telescopic and lever type shock absorbers and also steering dampers 
439 Guide Pin, shouldered
For removing and installing the inner transmission shift lever bushes in gearshift housing
For removing the ball bearing from the generator armature on the commutator side
For installing
 - the bushes for the inner transmission shift lever,
 - the bushes for the clutch pedal shaft,
 - the clutch pedal on the clutch pedal shaft 
440 Support Ring
For pressing out the steering ball from the lower torsion arm 
441 Base Block
For removing
 - the main drive shaft bearing,
 - the rear wheel bearing oil seal
For installing
 - the rear wheel bearing oil seal,
 - the differential housing bearings 
442 Thrust Pad
For installing the rear wheel bearing oil seal
 
446 Tube
For removing
 - the inner front wheel bearing outer ball race with 59, 62, and 72 mm dia.,
 - the outer race of the outer front wheel bearing with 62 mm dia.,
 - the inner race of the inner front wheel bearing,
 - the inner race of the outer front wheel bearing
For installing the brake pedal bushes 
447 Thrust Plate
For removing the outer ball race of the inner front wheel bearing with 62 mm dia. 
447a Thrust Plate
For removing the outer race of the inner front wheel bearing with 59 mm dia. 
447b Thrust Plate
For removing the outer race of the inner front wheel bearing with 72 mm dia. 
447c Thrust Plate
For removing the outer race of the inner front wheel bearing 
447d Thrust Plate
For removing the outer race of the outer front wheel bearing 
447f Thrust Plate
For removing the outer race of the outer front wheel bearing with 45 mm dia. 
447g Thrust Plate
For removing the outer race of the inside front wheel bearing with 59 mm dia. 
447h Thrust Plate
For installing the outer race of the outside front wheel bearing with 45 mm dia. 
447i Thrust Plate
For installing the outer race of the inner front wheel bearing with 59 mm dia. 
447t Thrust Plate
For removing the outer ball race of the inner front wheel bearing with 72 mm dia. 
448 Thrust Plate
For removing the outer race of the outer front wheel bearing with 48 mm dia. 
449a Toothed Thrust Ring
For removing drive pinion roller bearing inner race from drive pinion with Klingelnberg toothing (7 : 31) 
449b Toothed Thrust Ring
For removing drive pinion roller bearing inner race with Gleason toothing (8 : 35) 
449c Toothed Thrust Ring
For removing drive pinion roller bearing inner race with Gleason toothing (7 : 31)
 
449d Toothed Thrust Ring
For removing
 - the drive pinion needle bearing inner race,
 - the 1st gear thrust washer,
 - the ball bearing from drive pinion with Klingelnberg toothing (8 : 33),
 - the ball bearing from drive pinion with Klingelnberg toothing (8 : 35) (only with Type 2/1 ton model) 
449f Toothed Thrust Ring
For removing the drive pinion ball bearing from drive pinion with Gleason toothing (8 : 35) 
449f Toothed Thrust Ring
For removing the drive pinion ball bearing from drive pinion with Gleason toothing 
450a Tool Board
For tool VW 401 and subsequent numbers 
451 Thrust Plate
For removing the differential bearings (from Chassis No. 469 447) 
452 Gear Carrier Support
For removing the transmission out of the gear carrier
For installing the main drive shaft bearing in the gear carrier
 
454 Pressure Piece for the Differential Bearings
For pressing
 - the tapered roller bearing off the differential housing (from August 1967),
 - the tapered roller bearings onto the differential housing,
 - the tapered roller bearings onto the drive pinion 
455 Sleeve for Differential Housing Bearings
For pushing on
 - the differential housing tapered roller bearings (from August 1967),
 - the differential housing tapered roller bearings (Type 1 automatic) 
456 Support for Gear Carrier
For pressing out the drive shaft from the gear carrier (from August 1967)
For pushing off the tapered roller bearings from the differential in conjunction with VW 457 
456a Support for Gear Carrier (3 parts)
For pressing out
 - the drive shaft from the gear carrier (from August 1970),
 - the gears from the gear carrier with the aid of the supplementary parts
For pressing off the tapered roller bearing from the differential when used in conjunction with VW 457
For pressing the ball bearing for the drive shaft into the gear carrier, when used in conjunction with the supplementary parts 
457 Angled Thrust Plates for Differential Bearings
For pressing out the gears from the transmission case (only VW 457/1) used in conjunction with VW 296
For pushing off the bearings of the differential (from August 1967) used in conjunction with VW 296 
458 Thrust Plate with Pins
For pushing out the tapered roller bearings from the final drive cover 
459 Appliance for Pressing the Ball Joints In and Out (2 parts)
For pressing
 - the ball joints into and out of the torsion arms,
 - the outer race of the tapered roller bearings out of the adjustment nut of the drive pinion (VW 459/1 only)
 
460 Removal Device (3 pieces)
For removing the upper king pin from the steering knuckle
For installing the piston pin bush with drift out of VW 460


460 Removal Device (2 parts)
For removing the upper king pins from the steering knuckle with VW 460/2 and 3 as well as VW 407
For pressing down the 3rd gear onto the pinion with VW 460/3 when taking off or fitting the circlip with VW 161a 
461 King Pin Installing Device (7 parts)
For insuring that the upper king pin is pressed correctly into the lower king pin
 
 
463 Removal and Installation Device (4 parts)
For pressing the inner needle bearing ring off the torsion arm
For installing the inner needle bearing inner ring on the torsion arm 
470 Thrust Pieces with Retaining Ring for Drive Pinion Bearing (3 parts)(automatic transmission)
For pressing the tapered roller bearings off the drive pinion 
471 Peening Tool for Ball Joints
For peening the ball joints in the torsion arms 
472 Thrust Pad with Spacer Sleeve
For pressing out the outer race of the tapered roller bearing from the bearing cover
For pressing
 - the outer race of the tapered roller bearing into the bearing cover,
 - the oil seal into the bearing cover in conjuction with VW 472/2 
473 Thrust Piece
For pressing
 - the oil seal out of the bearing cover,
 - the outer race of the tapered roller bearing into the bearing cover,
 - the outer race of the tapered roller bearing out of the bearing cover,
 - the outer race of the tapered roller bearing out of the adjustment nut,
 - the oil seal into the bearing cover 
474 Pressure Piece
For pulling the oil seal into the trailing wishbone 
 
500 Engine Support
For holding the engine during fitting work, used in conjuction with VW 313 and an assembly stand 
501 Wear Measurer Appliance for Valve Guides
For measuring the rock between the valve and the valve guide 
503 Puller for Ball Bearing
For pulling the ball bearing out of the crankshaft 
504 Valve Assembly Appliance (2 parts)
For inserting the cylinder head when using the valve spring compressor to remove or intall the valves 
505 Hook
For removing and installing the engine in conjunction with the workshop crane 
506 Thrust Pad (Crankshaft front seal)
For pulling the crankshaft seal into its housing 
507 Thrust Pad (Crankshaft rear seal)
For pushing the crankshaft seal into the clutch housing in conjunction with VW 295 
508 Mandrel (Oil seal/Drive shaft)
For inserting the oil seal of the drive shaft in conjunction with VW 295 
509 Transmission and Differential Retaining Bracket
To hold
 - the transmission during assembly work in conjunction with VW 313 and an assembly stand,
 - the differential during assembly work in conjunction with VW 313 and an assembly stand 
510 Thrust Pad (Bearing race/pinion and bearing/bearing cover)
For pulling in the small taper roller bearing outer race for the pinion in conjunction with VW 511 and VW 517
For pressing the ball bearing into the bearing cover 
511 Thrust Pad (Bearing outer race/pinion)
For pulling in the large taper roller bearing outer race for the pinion together with VW 517 and VW 518
 
512 Thrust Pad (Seal/pinion)
For installing the pinion seal in conjunction with VW 295 
513 Thrust Pad (Seal/bearing cover and outer bearing race/bearing cover)
For pressing
 - the radial seal into the bearing cover,
 - the taper roller bearing outer race into the bearing cover of the differential housing 
514 Tube Wrench
For tightening and loosening the threaded ring in the cover of the flange shafts 
515 Special Wrench for Pinion and Flange Shaft Nuts (3 parts)
For loosening and tightening
 - the nut on the pinion with SW 41
 - the nut on the flange shaft with SW 46 
516 Tube 42 mm dia. (Taper roller bearing/pinion)
For pressing the large taper roller bearing onto the pinion 
517 Threaded Spindle (Bearing outer race/pinion)
For pulling in
 - the large taper roller bearing outer race in conjunction with VW 511 and VW 518,
 - the small taper roller bearing outer race in conjunction with VW 510 and VW 511 
518 Thrust Pad (Bearing outer race/pinion)
For pulling out
 - the large taper roller bearing outer race in conjunction with an internal puller,
 - the small taper roller bearing outer race in conjunction with an internal puller
For pulling in the large taper roller bearing outer race in conjunction with VW 511 and VW 517 
519 Tube 50 mm dia. (Flange shaft/bearing cover)
For pushing the flange shaft into the bearing cover 
520 Tube 28.5 mm dia. (Taper roller bearing/counter shaft)
For pressing the small taper roller bearing onto the counter shaft 
521 Adjusting Device for the Ring Gear (6 parts)
For adjusting the backlash of the ring gear 
522 Support Sleeve for Assembled Drive Shaft
For pressing off the sliding joint of the drive shaft 
523 Pressing Tool
For pressing the tapered bolt out of the lower universal joint of the steering column 
524 Dowel Wrench
For loosening and tightening the threaded ring for the steering pinion swivel bearing 
527 Checking Device for front Wishbones
For checking the front wishbones and wishbone mountings 
529 Driving Sleeve for Valve Stem Seal
For driving the valve shaft seal onto the valve guide using the plastic fitting sleeve 
530 Tensioning Plate for Countershaft
For pre-loading the taper roller bearing for the countershaft 
531 Securing Bracket for Steering Gear
For clamping the steering gear into a vice in order to carry out assembly work 
532 Adjustment Gauge for Brake Pressure Regulator
For checking and adjusting the linkage of the brake pressure regulator 
534 Securing Device (Steering gear/pinion)
For slackening the threaded ring of the self aligning bearing/steering pinion, in conjunction with the steering gear housing cover
For tightening the threaded ring of the self aligning bearing/steering pinion 
535 Adjustment Gauge for Clutch Release Lever
For adjustment of clutch release lever 
540 Engine and Transmission Support
For holding the engine and transmission during assembly and disassembly in conjunction with VW 313 and an assembly stand (Dasher) 
541 Valve Assembly Appliance (3 pieces)
For removal and installation of the valves (Dasher) 
542 Guide for Bonded Rubber Mounting
For installation of the bonded rubber mountings in the front wishbones and the rear trailing arms (Dasher) 
543 Wishbone Checking Appliance
For checking the front wishbones for distortion (Dasher)
Note: only necessary if VW 527 (Type 48) with supplementary part VW 527/4-6 is not available 
544 "Y" Wrench
For fitting the race in the final drive (Dasher - automatic transmission) 
545 Drift
For installation of the governor oil seal and needle bearing (Dasher - automatic transmission) 
546 Compressing Tool
For pressing down the bucket tappets when removing and installing the clearance discs (adjusting the valve clearance) (Dasher) 
549 Shim adjustment for output shaft  
549a Shim adjustment for output shaft 
638 Torsion Arm Bushing Extractor
For extracting the bushing from the torsion arm 
 
642 Front End Swing Lever Shaft Extractor
For extracting the center pin on a Bus front end 
643 O-Ring installer?
Possible for master cylinder rebuilding? 
650 Cylinder Retainer
For retaining cylinders when removing and installing heads 
653 Valve Compressor
For compressing valve springs with the engine installed. 
655/3 Compressor
For various compressing purposes, such as ball joing front trailing arms after replacing ball joints, and compressing spring plates on the rear axle when installing. 
664 Holding Tool
For holding differential, splitcase transmission 
664-2 Holding Tool
For holding differential, tunnel swingaxle transmission 
674 Dash Eschuteon Tool
For removing dash-mounted switches 
690 Bearing Tool
For installing the upper outer bearing on the driven axle, reduction box (Type 2) 
691 Type 3 tune-up tool
For checking linkage rod length and adjusting dual carbs on Type 3. 
691? ? 
693 Reduction Box Lower Axle Bearing Press
 
709 Hood Spring Tool
For installing the hood springs on the Type 3   
769 Outer Wheel Bearing Tool
For checking and setting outer wheel bearing play, front axle 
778 Master Cylinder Rebuild Tool
For installing the piston seals
  
780-1 Ball Joint Boot Retaining Ring Installer
Bus 
780-2 Ball Joint Boot Retaining Ring Installer
Beetle, Ghia, and Type 3. 
1004 Box Wrench 10 mm
For removal and installation of single port intake manifold nuts 
10-201 Retainer
For locking the flywheel when undoing and tightening the attachment screws of the clutch and flywheel (Dasher)
 
 
10-202 Extractor
For extracting the needle bearing out of the crankshaft (Dasher) 
10-203 Puller
For pulling in the front oil seal of the intermediate shaft and crankshaft (Dasher) 
10-204 Mandrel
For pressing on the valve stem seal (Dasher) 
10-205 Fitting Sleeve
For fitting the crankshaft oil seal at the flywheel end (Dasher) 
10-207 Engine Suspension Chain
For removal and installation of the engine in conjunction with the workshop crane VW 1202 (Dasher) 
10-208 Pliers
For removing and installing the bucket tappet clearance discs (adjusting valve clearance) (Dasher) 
10-212 Assembly Tray for Tappet Clearance Discs
For storage of the tappet clearance discs (Dasher) 
10-218 Pliers
For removing the valve stem seal and the valve spring seat (Dasher) 
10-219 Extractor
For removing the front crankshaft oil seal (Dasher) 
10-220 Puller Ring
For fitting the crankshaft oil seal at the flywheel end (Dasher) 
10-222 Engine Support Bracket
For removing and installing the sump as well as the complete engine and transmission unit including subframe (Dasher and NSU K70) 
30-205 Thrust Pad
For removing and installing the outer race of the drive pinion roller bearing (Dasher) 
30-210 Fitting Tool
For installing the power unit rear bonded rubber mounting (Dasher) 
30-211 Support Bridge
For installation of the bearing of the drive shaft (Dasher) 
30-212 Punch
For installing the oil seal in the final drive (Dasher) 
40-20 Press Tool
For pressing out the taper ball bearing from the wheel bearing housing (Dasher) 
40-200 Camber Adjusting Lever
For adjusting the camber of the front wheels (Dasher) 
40-201 Shock Absorber Wrench
For loosening and tightening the screw cap of the shock absorber (Dasher) 
40-204 Tensioner
For pressing on the inner constant velocity joint of the drive shaft (Dasher) 


email:  toolstore@aol.com


Product Search

News

Events