test
This Page Type is Not Defined
ZDMAK SPECIAL TOOLS: MERCEDES TOOLS
 
Spring Compressor Kit 224.00
Coil Spring Compressor Kit for Mercedes. For front and rear coil springs. Applicable: W107, W116, W123, W124, W126, W129, W140, W170, W201, W202, W208 and W210.
Comes with carrying case.
Compress front & rear axle springs on models with idler arm & some MacPherson type suspensions.
Same as 924 589 0231 00.
Telescopic range 120mm 325mm. You get 2 Plates sizes 90/150mm and 2 Plates size 70/130mm.
MacPherson Strut Coil Spring Compressor 299.00
MacPherson Strut Coil Spring Compressor
Includes 3 pairs of Jaws. For compressing several types of Mac type front and rear springs.
Especially for 110, 120 and 130 springs found on many Mercedes.

Shoes (jaws) Sizes
125 215mm
88 160mm
65 125mm
and carrying case

Applicable BMW:
E31, E32, E34, E36, E39, Z3, Z3 coupe
Applicable Mercedes:
W163, 164, 171, 203, 209, 210, 211, 219, 230, 245, 251
B90 M Mercedes Hub/Wheel Bearing R&R Kit 274.00
The Original B90 Kit Designed to efficiently remove or install wheel bearing and hubs of spindle assemblies. Chassis W124, W129, W201, W202 Models with S.R.W.B and I.R.S. Email with any questions.
Timing Chain set up Double Row 225.00
Master Link Timing Chain Tool Double Row Set up SAME AS BENZ NUMBER 000 589 5843 00 Used for proper assembly of timing chain master link. OM601, OM602, OM603, OM615, OM616, OM617

Single row adapter and/or KIT available.
The single row set up is the same price as this kit.....email...
Mercedes Dash and Ignition Kit 17.50
MERCEDES DASH SERVICE TOOL KIT
Set Includes: Ignition "V" shape lock release wires same as Mercedes Number 900 589 0059 00
Plus a pair Long Hooks (overall length 6.5 inches)
(Similar to Mercedes 140 589 0223 00 the mercedes hooks are 7 inches the ones in this set are 6.5 inches)
You get the radio removal Keys (Pair)
Details:
Ignition Lock Removal (wires) Set for W124, 126, 201
Pair of Hooks for W107, 116, 123, 124, 126, 140, 201
Radio Removal keys FOR "1997 and OLDER" W129, 140, 202, 210
Mercedes Valve Spring Compressor 149.00
M0068 Valve Spring Compressor Kit M0068 For 6 and 8 cylinder engines. Same as Benz Number 123 589 0361 00 Spring Compressor Kit used for R&R of valve spring or rocker arm. Job can be done with the cylinder head on or off the car. Applicable: M 114, 115, 116, 117, 123, 130, 180
Hub Securing Bar Holder 29.99
ON SALE Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.
Guide Rail Pin Puller for Mercedes 39.99
Mercedes Rail Pin Puller Guide
This Puller has an Overall Length of 85mm and is designed with a thrust bearing to ease the pulling action. Used for the proper extraction of rail pins from cylinder head. Especially useful in restricted spaces where other pullers and slide hammers will notfit. Comes with a 6mm extractor pin. Applicable: Mercedes M102, M110, M115, M116, M117, M130, OM601, OM602, OM603, OM615, OM616, OM617.

In the 4 cylinder and 6 cylinder engines, this tool also removes the timing chain tensioners pivot pin, which is hidden behind a bolt in the front right (facing forward) face of the cylinder head. It of course also removes all of the timing chain guide rail mount pins that are located in the left (facing forward) of the cylinder head, and down in the left face of the engine block. Extremely handy when doing jobs with the engine still in the car, such as headgasket replacement, timing chain tensioner replacement, or timing chain guide rail replacment. Works in all carbureted and fuel injected gasoline, and all diesel injected 4 cylinder and 6 cylinder engines as found in w108, w109, w110, w111, w112 chassis cars built in the 60s, as well as other models that use pins to secure guide rails.
Diesel Injection Pump Socket 34.99
Diesel Injection Pump Socket Tool 32 Point Female Socket with 1/2" drive.
This socket is used for the R&R of delivery valve of diesel injection pump. Applicable: Mercedes diesel engines 601, 602, 603, 605, 606, 617, 1982 and up Note mercedes ref 617 589 0109 00
Front Lower Control Arm Tools 174.50
Front Lower Control Arm Tools M0062 Press Kit needed for the proper installation of bushings into the front lower control arms. Applicable: Mercedes chassis W124, W129, W140. Each press washer has its own thrust bearing which eases the pressing action. This reduces friction, wear and tear of the tool, ensuring longevity.
5 Piece Set with 65mm Wrench 79.00
Set 5 Tools for Mercedes repair.

1.Hub Securing Bar 113 0040 Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable:M112 & M113

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER

4. Long Pattern Thin wrench 36mm. Comes with rubber handle grip.

5. Thin Wrench 65mm with an 8mm overall thickness and an overall length of 16 inches for proper leverage. Mercedes ref: 120 589 0201 00.

You get all 5 tools with this purchase.
Pin Wrench Socket 85.50
M0007 Threaded Pin Wrench Socket This tool is used for the proper R&R of threaded ring which secures prechamber in cylinder head. The Mercedes number for this tool is 615 589 0007 00 Applicable: OM601/602/603 engines through 1989 with vertical injection. Also OM615, OM616, OM617 Ref: 615 589 0007 00
Special Male Socket 59.50
Special Male Socket M0009 Male Splined Socket with 1/2" drive. Used for the proper R&R of threaded ring which secures prechamber in cylinder head. Applicable: Mercedes 1990 up 602/603 engines with inclined injection, and all 604/605/606 Ref: 604 589 0109 00
Extractor Tip Double Ended 44.50
Extractor Tip Double Ended M0046 Used for the proper removal of prechamber from cylinder head. Used in conjunction with a slide hammer. Applicable: Mercedes engine OM601, OM602, OM603, OM604, OM615, OM616, OM617. Ref: 902 589 0033 00
Metal Clad Bushing R&R Kit 99.95
Metal Clad Bushing R&R Kit
Please read carefully: Tool set for replacing the wheel carrier bushing at the rear wheel carrier assembly (where all the links attach), and it works as good as the factory tool.
Some people wind up taking off every single link and bending the dust sheild while trying to R&R this bushing (with a standard shop press).
This tool is worth its weight in gold.
Although this tool is an aftermarket tool for the MB tool 202 589 00 43 00, it worked excellent in the field, and its about 1/2 the cost of the OE MB tool.
It works on Mercedes Benz chassis: 124, 129, 140, 170, 171, 201, 202, 203, 208, 209, 210, 215, 220, 221, 230, spanning 1984 present models
(not every model however, mainly the ones listed above).

w124 (1986 1995 300E/E320, 300D, E300D, 400E, 500E,etc), R129 (1992 2002 SL Models), w140 (Sclass from 1991 1998), R170, R171 (All SLK models, thru current), w201 (all 190E/D models), w202 (C class 1993 2000) w203 (c class 2000 2006), w208 & w209 (all CLK models), w210 (E Class 1996 2001), w215 (CL Class Coupe 1999 2006), w220 and w221 (S Class 1996 2006, S class 2006 present), and R230 (the new SL roadster). It is used to replace MB Bushing 220 352 02 27, which are now 221 352 00 27.

SAME AS 202 589 00 43 00 Removal and Installation Wheel Carrier Support Joint
(REPLACES) 140 589 07 43 00 Removal and Installation Tool
(REPLACES) 201 589 05 43 00 Removal and Installation Tool

This set comes complete with all the proper components to efficiently get the job done right. This tool works both on the car or on the bench!
Mercedes Hooks Long 23.00
Dash Pulling Hooks "Long Pattern" ITEM M0060 L Wire Hooks (Pair) long pattern needed for the proper removal of instrument cluster. Length of reach is over 7 inches. For Newer models.
U Body 8mm Allen Socket 49.99
Special "U Shape" Body 8mm Allen Socket with 1/2 inch drive tool needed for the proper removal and replacement/torquing of cylinder head bolts under the rocker shaft. Applicable: Mercedes V 8 engines. Ref 916 589 0013 00
Mercedes Ball Joint Press Tool 299.00
Mercedes Ball Joint Press Tool M0063 Press Tool for the proper installation of ball joint into steering knuckle. The design of this tool allows for mounting in a vice w/o marring the tool or bending under pressure. Applicable: Mercedes chassis W116, W123, W126. Big Time Saver! Made from High Quality Steel, Incorporated with a heavy duty solid thrust bearing, A must for the Professional Mercedes Mechanic! Ref: 116 589 0462 00

Call or email for lower price. Be sure to include a phone number in your email in case we need to call you back. We may have what we call "tool truck samples" or "scratch and dent" items just like this one or virtually brand new we may be able to sell at a lower price all depending upon inventory levels.
Feel free to call our toll free number 877 938 6657. Canada please email.
Parking Brake Spring Installer 29.95
This tool is used for proper R&R of pressure spring on parking brake shoe. Applicable: All Models.
Two (2) Tools For Mercedes 84.00
SET 2 Repair Tools For Mercedes. This is the correct pin socket required to remove the input flange from the differential on all w110, w111, w108, and w109 chassis Mercedes cars built during 1961 to 1972 with swing axle style rear differential/axle assemblies. More Details:
Diagram on Tool 1a If you have a leak at the differential input flange oil seal, this tool removes the special nut located down inside the flange. Once this nut has been removed, the flange pulls off, exposing the input seal.
When reinstalling the nut using this tool pay close attention not to over tighten the nut so that the differential pinion bearings are not damaged.
There is a similar nut and flange at the rear of the transmission, however, it requires socket number TOOL 1b. (see images)
Diagram on Tool 1b

Buy these as a pair, and be well prepared to change out your leaking 40 year old transmission output and differential input seals."
You get both tools with this purchase..
Ball Joint Tools 169.00
Ball Joint Tool This tool set is used for removing and installing the ball joint into the steering knuckle. Applicable: 211 E Class 2002 and newer. 215 CL Class 2002 and newer. 219 CLS 2006 and newer. 220 S Class 2000 and newer. 230 SL Class 2003 and newer (NOTE: THIS KIT IS THE SAME AS OTHER ITEM M220 0343)
Differential Sub Frame Kit 125.00
Mercedes Differential Sub Frame Kit M0074 Bushing Tool needed for R&R of differential sub frame bushings. This is the most efficient unit on the market. Each driver nut has its own thrust bearing which eases the pressing and pulling action. This reduces friction, wear and tear of the tool, ensuring longevity. Applicable: Mercedes chassis W124, W140, W201.

Call or email for lower price. Be sure to include a phone number in your email in case we need to call you back. We may have what we call "tool truck samples" or "scratch and dent" items just like this one or virtually brand new we may be able to sell at a lower price all depending upon inventory levels.
Feel free to call our toll free number 877 938 6657. Canada please email.
2 Piece Set 24.99
1.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

2.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER.
Cam Holding Wrench Kit 39.50
Cam Holding Wrench Kit Holds camshaft in 40 degree TDC position (left/right side) 32mm Appl.: 1998 and newer Mercedes Benz with V6 and V8 engines (M112, M113) 38mm special wrench for turning the cam. This special Cam Securing Master Wrench Kit has all the necessary components to properly adjust and lock the cams into position. Comes as shown with (1) Cam Wrench and (2) Cam Alignment Plates

Application Detail: 
M112 V 6 Engine
19982005 C240
19982004 CLK240
19982004 E240
19982004 C320
19982004 E320
19982005 S320
19982003 ML320
19982004 CLK320
19982003 SLK320
20032008 Chrysler Crossfire
20012003 C32 AMG
20012003 SLK32 AMG
20052006 Chrysler Crossfire SRT 6
20032005 ML350
20032005 S350

M113 V 8 Engine
1998 2003 CLK430
1998 2002 E430
1999 2001 ML430
1998 2000 C43 AMG
1999 2006 S430
2001 2006 CL500
2002 2006 CLK500
2003 2006 E500
2002 2008 G500
1999 2006 S500
1999 2006 SL500
2001 2006 ML500
2001 2002 CL55 AMG
1998 2002 CLK55 AMG
1998 2002 E55 AMG
2001 2003 ML55 AMG
2001 2003 S55 AMG
2002 2003 G55 AMG
2004 2008 SLK55 AMG
2005 2007 C55 AMG
2002 2006 CL55 AMG
2002 2006 S55 AMG
2002 2006 SL55 AMG
2004 2006 E55 AMG
2004 2008 G55 AMG
722.6 Transmission Dipstick 26.50
Mercedes Transmission Dipstick Benz reference number 140 589 1521 00 For determining fluid level newer Mercedes with electronic transmission 722.6 The graduations on the fluid end (plastic dipping end) are: (Range) 25 (low) to 80 (high) The picture is not to scale.
Testimonial: The only way to properly fill/check correct fluid level on 722.6 Transmission. Mercedes has lowered the recommended service intervals of these transmissions which makes this dipstick a must have. For the most common Mercedes Transmissions. NC Technician/Shop Owner Robert Palmiter
Mercedes 8mm Dogleg Allen 13.99
Sturdy 1/2 Drive Dog leg (offset) 8mm Allen Socket Applicable: M116, 117
1/2" drive
Overall length of the tool is 4 1/4 inches.
Tool used for R&R of cylinder head bolts.
Similar to Mercedes number 000 589 3407 00.
Mercedes & BMW Set 99.99
7 Pc Set tools for Benz and BMW repair. Including 4 Mercedes Tools a BMW Waterpump Hub Holding Tool plus 2 Thin Wrenches.
Benz Tools are:
1.Hub Securing Bar 113 0040 Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable:M112 & M113

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator: Mercedes M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm is used for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 819 86 and Newer
4. Thin Wrench 65mm with an 8mm overall thickness and an overall length of 16 inches for proper leverage. Mercedes ref: 120 589 0201 00

BMW Double Waterpump Tool This special tool covers most popular applications used for securing Water Pump Hub from rotating during R & R of Fan Clutch Nut Applicable:M10, M20, M30, M40, M41, M42, M50, M60, M62

You will get all seven tools with this purchase.
Set with Slide Hammer 79.00
Extractor Tip Double Ended M0046 Used for the proper removal of prechamber from cylinder head. Used in conjunction with a slide hammer. Applicable: Mercedes engine OM601, OM602, OM603, OM604, OM615, OM616, OM617. Ref: 902 589 0033 00
Plus
Slide Hammer use with Tool M0046 for proper removal of prechamber from cylinder head. Also other applications: Tool pulls dented sheet metal back into place. To use, drill a hole in the deepest part of the dent, insert the hook or self threading screw tip and tap lightly with the 2 1/2 lb slide hammer to remove the dent. A 15 inch long shaft enables high pulling force.
Airmatic Suspension Tool 169.00
Mercedes "AIRMATIC" Strut Tool Kit
Suspension Tools for Mercedes Special design for the crucial task of R & R of Strut Assembly. This kit tackles snap ring of the head cover housing the bearing of the front axle air suspension strut Applicable: W220
Mercedes Valve Tool Set 3 150.00
Mercedes Valve Adjustment Wrench Set of 3 Tools Made in Germany by Hazet This three piece set includes:Hazet Item Numbers 2769, 2769 1 and 2769 3
Locking Nut 39.95
Locking Nut M0039 needed for securing the diesel injection pump cam shaft. Applicable:Mercedes OM601, OM602, OM603, OM605, OM606, OM617. Benz Ref: 601 589 0521 00
SLIDE HAMMER PIN PULLER 137.00
This set is used for extraction of rail pins from cylinder head while out of car. Impact Type Slide Hammer / Rail Pin Puller Comes complete with a set of 5 Extractor Pins This is an easy to hold, hand sized slide hammer. The Mercedes Number is 116 589 2033 00
No Go Gauge 59.95
Mercedes
Go No Go Gauge* Used for checking hydraulic valve lifters Applicable: Mercedes V 8 engines 1976 and Newer * Excluding M119. Ref: 917 589 0623 00
8 Piece XZN Set 38.99
XZN Metric Socket Set 8 Piece
OUR BEST SELLER!
These are Triple Square Sockets
XZN means Triple Square (12 point)
If your tool books call for XZN or TRIPLE SQUARE or 12 POINT, these are probably the tools you need. 
These are Short Pattern "Stubby" Sockets
Each tool is 1 1/2 inches long.
Sizes included: M4, M5, M6, M 8, M10, M12, M14 & M16
Short pattern for using when you are in a tight spot.
Sturdy compact solid one piece design.
3/8 Drive Size.
Satin Chrome with black impact tips. New S2 Alloy Steel.
These are some of the strongest drivers you will find.
Comes in the plastic carrying case.

Triple square, also known as a XZN socket, is a type of screw drive. They are commonly found on German vehicles such as BMW, Mercedes, and Volkswagen etc... 
These screws/fasteners are used in some high torque applications such as cylinder head bolts and drive train components. 
Triple square bolts are common to early Porsche and Volkswagen (CV) constant velocity joints.
Most common earlier sizes would be 6, 8, 10, and 12. 
Increasingly, triple square screws are found on other European and Asian makes of cars.
Other names for triple square screws and drivers are "Double Hex", "Double Allen", and "Aircraft Screws". 
Despite this, "Double Hex" and "Double Allen" are misnomers. The recess in these bolts is actually (as the name suggests) made of three squares, not two hexagons. 
The corners are 90 degrees, not 120 degrees. They are not double hexes, and an Allen key will not fit them properly.
Metric Hex Stubbies 38.00
Metric Hex Stubbies (short pattern) 1/4 Drive 9 Piece Set. Similar to the Hex tools made popular by Hazet Stubby Hex Metric Sockets in the most Popular smaller sizes.
EACH TOOL IS ONE INCH LONG.
These are the sturdy one piece design.
Hex / Allen sockets sizes included: 2mm, 2.5mm, 3, 4, 5, 6, 7, 8, 10mm.
S2 Alloy steel THE STRONGEST DRIVERS AVAILABLE! Heat treated to 56 to 62 RC. Satin Chrome plating. Comes in the plastic case.
This set is great and is a must for working on MERCEDES, BMW, VW, AUDI or PORSCHE. These are very strong and fit in very small areas. Great when disassembling or assembling engine/transmission. Real time savers!
Expansion Tank Adaptor 56.00
M0077 Expansion Tank Adaptor Used for pressurizing the liquid cooling system on models with a "male" threaded filler neck on expansion tank. Applicable: Mercedes E Class 96 and Newer.
TANK ADAPTER 19.99
Expansion Tank Adaptor VZ32 Applicable: ML Class 98 Newer Models with male threads on filler neck of expansion tank.
Metal Clad Bushing Kit 289.00
Metal Clad Bushing R&R Kit M0079 Needed for the proper R R of Front Metal Clad rubber mount bushings of the rear axle carrier sub frame. This Tool has been ?Field Tested? and redesigned. Incorporating a thrust bearing for easy pulling / pushing action, reducing the wear & tear of the tool. This Bushing Tool comes complete with the proper components to get the job done right. Applicable: Chassis W 124, W 129, W 201, W 202, W 140
Metal Clad Bushing Kit 299.00
M0087 Bushing Kit Metal Clad Bushing Kit Needed for the proper R&R of FRONT metal clad rubber mount bushings of rear axle carrier sub frame. This special service tool has been thoroughly ?Field Tested? and redesigned. Incorporating a thrust bearing to ease the pulling / pushing action, reduces the wear & tear of the tool ensuring longevity. This Bushing Tool comes complete with all the proper components to efficiently get the job done right. Applicable: Chassis W 124, W 129, W 201, W 202, W 140.
Chain Guide Timing Tool 86.95
Mercedes Chain Guide Timing Tool M0037 This Chain Guide is designed for efficient and proper installation of timing chains. Applicable: Mercedes V 8 engines.
Metric Wrench 4 Piece Set 60.00
Spanner Wrench Set needed for R&R This 4 pack set includes (1) each of the following wrench sizes: 27mm, 30mm, 32mm, 36mm. Some pplications include: Porsche models 911, 930, 914 6, 944, 968. This is a German Car Specail * This set is great for the European Automotive Technician. Very Handy Tools!
Mercedes Oil Filter Wrench 13.99
Oil service Wrench 74mm with 14 Points (inside flats flutes).
This is an excellent deal. This tool has 2 bonus screws for more strength if needed.
The screws are kept in the holes at the top when not in use and can be used inserted into the side holes making the tool more effective.
Some applications include: Mercedes, Audi, VW Golf, and New body Jetta, TDI (Diesel) and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle. Mercedes M104, M110, M111, M119, M120 C, E etc...
Porsche 944 and 924. Some Toyota. Check your manuals for details and size needed. Measure filter diameter or canister diameter.
See chart below.
bullet Audi Coupe 81 87
bullet Audi Coupe Q 20v 90 91
bullet Audi Fox 73 79
bullet Audi 100 89 91
bullet Audi 100Q 89 91
bullet Audi 4000 4 Cyl 80 87
bullet Audi 4000 5 Cyl 80 81
bullet Audi 4000 Q 84 87
bullet Audi 5000 78 88
bullet Audi 5000 Q 87 88
bullet Audi 80 88 90
bullet Audi 90 88 90
bullet Audi 90 Q 20v 90 92
bullet BMW 325 85 88
bullet BMW 325e 84 88
bullet BMW 325es 86 87
bullet BMW 325i Sedan 87 91
bullet BMW 325i Cabriolet 87 93
bullet BMW 325is Coupe 87 91
bullet BMW 325ix 88 91
bullet BMW 525i 89 90
bullet BMW 528e 82 88
bullet Mercedes 190E 2.3 1985 1993
bullet Mercedes 190E 2.6 1987 1993
bullet Mercedes 260E 1987 1989
bullet Mercedes 300CE 1988 1989
bullet Mercedes 300E 2.6 1990 1992
bullet Mercedes 300E 1986 1992
bullet Mercedes 300E 4 Matic 1990 1993
bullet Mercedes 300SE 1988 1991
bullet Mercedes 300SEL 1988 1991
bullet Mercedes 300TE Wagon 1988 1992
bullet Mercedes 300TE 4 Matic Wagon 1990 1993
bullet Porsche 924 77 82
bullet Porsche 924 Turbo 80 82
bullet Porsche Cayenne S 03 04
bullet Porsche Cayenne Turbo 03 04
bullet Porsche 911/996 Carrera/2 98 04
bullet Porsche 911/996 Carrera/4 99 04
bullet Porsche 911/996 GT3 04 04
bullet Porsche 911 Twin Turbo 01 04
bullet Porsche Carrera GT 04 04
bullet Porsche Boxster 97 04
bullet Porsche 911 Turbo 1991 1994
bullet Porsche 924S 1986 1988
bullet Porsche 944 1983 1989
bullet Porsche 944S 1987 1988
bullet Porsche 944S2 1989 1991
bullet Porsche 944 Turbo 1986 1991
bullet Porsche 968 1992 1995
bullet Porsche 928 78 84
bullet Porsche 928 32 85 95V
bullet Porsche 911/993 Carrera/2 1995 1998
bullet Porsche 911/993 Carrera/4 1995 1998
bullet Porsche 911 Twin Turbo 1995 1999
bullet Volkswagen Dasher 74 81
bullet Volkswagen Fox 87 93
bullet Volkswagen Golf GL/GT 85 92
bullet Volkswagen Golf III GL 93 94
bullet Volkswagen Golf GTI 8/16V 85 92
bullet Volkswagen Golf III GTI 93 94
bullet Volkswagen Jetta 80 84
bullet Volkswagen Jetta GL 85 92
bullet Volkswagen Jetta(Canada) 93 99
bullet Volkswagen Jetta Carat 85 92
bullet Volkswagen Jetta III GL 93 94
bullet Volkswagen Jetta GLI 84 88
bullet Volkswagen Jetta GLI 16V
bullet Volkswagen Jetta III GLS
bullet Volkswagen Passat 16V 90 93
bullet Volkswagen Passat GL 95 97
bullet Volkswagen Quantum 4 Cyl 82 85
bullet Volkswagen Quantum 5 Cyl 83 88
bullet Volkswagen Rabbit 75 84
bullet Volkswagen Rabbit Convertible 79 87
bullet Volkswagen Rabbit Cabriolet 88 93
bullet Volkswagen Rabbit GTI 83 84
bullet Volkswagen Scirocco 75 88
bullet Volkswagen Scirocco 16V 86 88
bullet Volkswagen Van Water Cool 83 92
bullet Volkswagen Van Syncro 86 92 This tool can be used on the following filters
bullet Audi, VW: 070 115 561, 056 115 561G, 034 115 561A
bullet BMW: 11 42 1 266 773
bullet Mecedes: 102 184 01 01
bullet Porsche: 996 107 225 52, 993 207 201 02, 993 107 203 03, 928 107 201 05,
bullet 944 107 201 08
Long Thin Wrench 65mm 48.50
Thin Wrench 65mm ITEM M0081 65mm with an 8mm overall thickness and a length of 16 inches for proper leverage. Benz ref: 120 589 0201 00
Best Quality Thin Wrench Set 59.99
Set of 2 Long Pattern Thin Wrenches
German Car Special *
One of each size: 36mm and 32mm
Overall length of 20 inches.
Thickness of each wrench is 8mm. Tools will come with a handle grip on each.
Many applications for these two tools.
Locking Hook 11.99
Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103. Mercedes ref: 103 589 0040 00
Allen Wrench Holding Bar 8 x 10 19.50
On Sale...
Allen Wrench Holding Bar
Comes complete with 8 and 10mm Allen bits.
The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606
The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 1986 and newer.
Ref 900 589 0307 00
Spark Plug Wire Pliers 24.50
Spark Plug Wire Pliers
Used to remove the newer high voltage type wires
Wide grip section and special angle. makes it
easy to remove wires without separating crimps.
Applicable: 102, 103, 104, 110, 115, 116, 117, 119, 120
Same as Mercedes Tool Number 104 589 0037 00
also same as Zdmak item M104 0037X
Two Sets * Special 75.50
Triple Square and Hex Stubbies!
Here is a sweet combo set for a good price.
STUBBY XZN TRIPLE SQUARE 8 PIECE SOCKET SET
PLUS 9 PIECE HEX STUBBY SET

The Triple Square set description as follows:
Socket Set 3/8 Drive
Sizes included: M4, M5, M 6, M8, M10, M12, M14 and M16
Sturdy compact One Piece design.
Satin Chrome with black impact tips.
Super "New" S2 Alloy Steel. Fully Heat Treated

PLUS Metric Hex Stubbies 1/4 Drive 9 Piece Set Check it out.
Short Pattern Hex Metric Sockets in small popular sizes.
Available Now at a fair price.
These are the Sturdy One Piece Design.
Hex Sockets great for working on German Cars.
Sizes included: 2mm, 2.5mm, 3, 4, 5, 6, 7, 8, 10mm.
S2 Alloy steel THE STRONGEST DRIVERS AVAILABLE.
Drivers heat treated to 56 to 62 RC. Satin Chrome plating.
Both sets come in plastic carrying cases.
Heavy Duty 8mm Allen 32.15
Multiple applications for this handy tool.
Super Duty 8mm Allen Item P243 Extra Long 3/8 Drive Socket This 8mm Extra Long Allen Socket is a solid one piece construction. Overall length is 7.75 inches. Used for R & R of some Benz Cylinder Headbolts,
Engine M116 , M117.
Mercedes Ignition Turning Sleeve 41.50
Ignition Turning Sleeve M0045 Mercedes ref: 126 589 0714 00 This tool is perfect for the proper R&R of the protective cover for ignition / steering lock. Applicable: Mercedes chassis W123, W124, W126.
Ignition Turning Sleeve 41.00
Ignition Turning Tool
For loosening and tightening the ring (rosette) of the electronic ignition switch.
Applicable: W129, 140, 202 (as of June 1, 1997), 208, 210, 211, 230, 240, 463
The Aluminum will not leave marks on the interior parts.
Benz ref: 210 589 0007 00
Double Ended Ignition Turning Sleeve 75.00
M0082 Double Ignition Turning Sleeve Double Ended Tool Used for the proper R&R of protective cover from ignition steering lock. Applicable: Chassis W 202, W 123, W 124, W 126. Flat rubber insert ensures a firm grip and scuff protection. Benz ref: 202 589 0014 00
Double Ended Ignition Turning Sleeve 75.00
M0082 Double Ignition Turning Sleeve Double Ended Tool Used for the proper R&R of protective cover from ignition steering lock. Applicable: Chassis W 202, W 123, W 124, W 126. Flat rubber insert ensures a firm grip and scuff protection. Benz ref: 202 589 0014 00
Pin Wrench Socket 44.95
Groovenut Socket 1/2 inch Drive
Ref: Same as 915 589 0207 00
This tool is used for R&R of grooved nut on rear axle shaft flange, necessary when replacing axle bearing or seal. Applicable: Mercedes chassis W107, W114 , W115 , W116 , W123 , W126. Models with constant velocity joint axles* Click here to see the Diagram on this Tool
Pin Wrench Socket 59.80
M0026 Pin Wrench Socket with 1/2" drive, needed for R&R of grooved nut on drive pinion shaft flange of differential. Applicable: Mercedes chassis W107, W114, W115, W116, W123, W126. Models with constant velocity joint axles. Click here to see the Diagram on this Tool
Pin Wrench Socket 36.50
M0028 Pin Wrench Socket With 1/2" drive, needed for R&R of grooved nut on front differential counter shaft. Applicable: Mercedes Transmission G76/18, G76/18A, G76/18C, G76/27, G76/27A, G76/27 5. Click here to see the Diagram on this Tool
Pin Wrench Socket 56.50
M0029 Pin Wrench Socket Pin Wrench with 1/2" drive, needed for R&R of grooved nut on transmission drive shaft flange. Applicable: Mercedes transmission K4A 025. Click here to see the Diagram on this Tool
Pin Wrench Socket 47.50
Pin Wrench Socket M0030 Picture not to scale Pin Wrench Socket with 1/2" drive. Used for R&R of grooved nut on drive pinion shaft flange of differential. Applicable: Mercedes swing axle types. The Mercedes Ref: 111 589 0507 00. Click here to see the Diagram on this Tool
Pin Wrench Socket 59.99
M0032 Pin Wrench Socket with 1/2" drive, needed for R&R of grooved nut on transmission drive shaft flange. Applicable: Mercedes transmission K4C 025, W4B 025, K4A 040 Click here to see the Diagram on this Tool
30mm Thin Wall Deep Socket 28.99
Specially designed 30mm thin walled 12 point, deep socket.
Used for the proper R&R of BMW transmission drive shaft flange nut and pinion drive shaft flange nut of differential.
This is a very handy multi purpose tool.
Also for some Mercedes R&R drive shaft flange.
Clutch Piston Assembly Sleeve 111.70mm 39.50
Needed for installing the clutch piston into the external disc carrier on transmission 722.4 722.1 722.3
Chain Guide Timing Tool 86.95
Mercedes Chain Guide Timing Tool M0037 This Chain Guide is designed for efficient and proper installation of timing chains. Applicable: Mercedes V 8 engines.
Set of Three Tools (3) 147.00
Set of Three including: Threaded Pin Wrench Socket (M0007) tool used for the proper R&R of threaded ring which secures prechamber in cylinder head. The Mercedes number for this tool is 615 589 0007 00
Applicable: OM601/602/603 engines through 1989 with vertical injection. Also OM615, OM616, OM617 Ref: 615 589 0007 00
Plus
Extractor Tip Double Ended (M0046) Used for the proper removal of prechamber from cylinder head. Used in conjunction with a slide hammer.
Applicable: Mercedes engine OM601, OM602, OM603, OM604, OM615, OM616, OM617. Ref: 902 589 0033 00
Plus
Slide Hammer use with Tool M0046 for proper removal of prechamber from cylinder head. Also other applications: Tool pulls dented sheet metal back into place. To use, drill a hole in the deepest part of the dent, insert the hook or self threading screw tip and tap lightly with the 2 1/2 lb slide hammer to remove the dent.
A 13? long shaft enables high pulling force. Slide hammer has 1/2 13 UNC thread.
Set of Three Tools (3) 147.00
Set of Three including: Threaded Pin Wrench Socket (M0007) tool used for the proper R&R of threaded ring which secures prechamber in cylinder head. The Mercedes number for this tool is 615 589 0007 00
Applicable: OM601/602/603 engines through 1989 with vertical injection. Also OM615, OM616, OM617 Ref: 615 589 0007 00
Plus
Extractor Tip Double Ended (M0046) Used for the proper removal of prechamber from cylinder head. Used in conjunction with a slide hammer.
Applicable: Mercedes engine OM601, OM602, OM603, OM604, OM615, OM616, OM617. Ref: 902 589 0033 00
Plus
Slide Hammer use with Tool M0046 for proper removal of prechamber from cylinder head. Also other applications: Tool pulls dented sheet metal back into place. To use, drill a hole in the deepest part of the dent, insert the hook or self threading screw tip and tap lightly with the 2 1/2 lb slide hammer to remove the dent.
A 13? long shaft enables high pulling force. Slide hammer has 1/2 13 UNC thread.
Mercedes Valve Spring Compressor 183.00
Valve Spring Compressor Kit M0067 used for R&R of valve spring or rocker arm. Job can be done with the cylinder head on or off the car. Applicable: Mercedes engine M110. 6 cylinder engines with dual cam shafts.
Mercedes Hub Wheel Bearing R&R Kit 274.00
Number B90 M
The Original B90 Kit Designed to efficiently remove or install wheel bearing and hubs of spindle assemblies. Chassis W124, W129, W201, W202 Models with S.R.W.B and I.R.S. Email with any questions.
Parking Brake Spring Installer 29.95
This tool is used for proper R&R of pressure spring on parking brake shoe. Applicable: All Models.
Live Data Hand Held Scanner 2890.00
Tired of high prices on Scanners? Serious Inquiries email sales@zdmak.com or call Toll Free 877 938 6657. X431 Master is the latest model of Launch X 431 series diagnostic tool. Launch products old world wide for a decade, the X 431 series has a reputation for its wide range of vehicles and full functions of its software. Based on the X 431, the Master gets a new structure and better design; also the hardware is upgraded. X431 Master will be released to the world wide market on 1st September, 2009. Inheriting from x 431 series, the X431 Master gets the open operating system: the highest level of automotive diagnostic technology in the world; function of read DTCs, read DataStream, actuation test, sensor waveform display and ECU coding as well as the PDA functions. It is easier and more convenient to operate than X 431 based on the smart design. The advantages of X431master compared to X 431:
1. Integrated design, combining the smartbox, miniprinter and main unit, a new designed and cover made from high quality materials to stand in a new market
2. Add the strap to the side face; easy to carry and ergonomical to use
3. The new smartbox add the The X431MASTER has a new connector to replace all CAN Bus and OBD Connector called OBDII 16E connector, which would be OK to test most of the vehicles.
4. Upgrade the hardware and communication modules, safer and faster communication with cars than X431 by intergraded design to save time in work
5. No more downloading of the diagnostic/communication software, start diagnosis program directly
6. 10.8V 40V operating voltage capability is added to work with different kind of batteries.
Double & Single Row Set up Complete 270.00
Master Link Timing Chain Tool
Single Row and Double Row Set up.
Used for proper assembly of timing chain master link.
OM601, OM602, OM603, OM615, OM616, OM617
(also M102, M103 AND M116)
You will get all (3) bits for double and single row.
Picture above is for reference only.
Pin Wrench, Extractor, & Splined Socket 193.00
Set of 3 Tools
First item: Threaded Pin Wrench Socket
Tool is used for the proper R&R of threaded ring which secures prechamber in cylinder head.
The Mercedes number for this tool is 615 589 0007 00
Applicable: OM601/602/603 engines through 1989 with vertical injection.
Also OM615, OM616, OM617 (Ref: 615 589 0007 00)
Plus you get
Extractor Tip Double Ended (Item M0046)
Used for the proper removal of prechamber from cylinder head.
Can be used in conjunction with a slide hammer.
Applicable: Mercedes engine OM601, OM602, OM603, OM604, OM615, OM616, OM617.
9Ref: number for this extractor is MB 902 589 0033 00)
Plus
Special Male Splined Socket with 1/2" drive.
Used for the proper R&R of threaded ring which secures prechamber in cylinder head.
Applicable: Mercedes 1990 up 602/603 engines with inclined injection, and all 604/605/606
Mercedes Ball Joint Press Tool 299.00
Mercedes Ball Joint Press Tool M0063 Press Tool for the proper installation of ball joint into steering knuckle. The design of this tool allows for mounting in a vice w/o marring the tool or bending under pressure. Applicable: Mercedes chassis W116, W123, W126. Big Time Saver! Made from High Quality Steel, Incorporated with a heavy duty solid thrust bearing, A must for the Professional Mercedes Mechanic! Ref: 116 589 0462 00

Call or email for lower price. Be sure to include a phone number in your email in case we need to call you back. We may have what we call "tool truck samples" or "scratch and dent" items just like this one or virtually brand new we may be able to sell at a lower price all depending upon inventory levels.
Feel free to call our toll free number 877 938 6657. Canada please email.
Body Tool Set 7 29.99
Body Hammer & Dolly Set 7 Pc
? Tough fiberglass hammer handles for extended service life ? Includes: Curved dolly, utlility dolly, double end dolly, shrinking dolly, standard bumping hammer pick, finish hammer, reverse curved hammer. Comes in molded case.
Metal Clad Bushing Kit 299.00
M0087 Bushing Kit Metal Clad Bushing Kit Needed for the proper R&R of FRONT metal clad rubber mount bushings of rear axle carrier sub frame. This special service tool has been thoroughly ?Field Tested? and redesigned. Incorporating a thrust bearing to ease the pulling / pushing action, reduces the wear & tear of the tool ensuring longevity. This Bushing Tool comes complete with all the proper components to efficiently get the job done right. Applicable: Chassis W 124, W 129, W 201, W 202, W 140.
5 Piece Set with 2 Long Wrenches 79.00
Five Tools for Mercedes Repair

Including:
1.Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER

4. Long Pattern Thin wrench 32mm. Comes with rubber handle grip.

5. Long Pattern Thin wrench 36mm.

You get all 5 tools with this purchase.
Radio Removal Set 21.50
This is the best price set on the market...Bar None! The competition does NOT offer this COVERAGE for the price they charge.
This is a Master Set and it is used with BMW, Mercedes, Volkswagen Audi, Porsche and DIN.
FULL COVERAGE on Volkswagen Audi.
What makes this set better is a total of 8 keys for VW Audi and two for BMW plus the grips on the keys are coated for easy use.
You will notice a total of 3 different sets for Volkswagen Audi, two different tools for BMW and a set for newer Mercedes that will also work with older Mercedes and also works with some Porsche. (Same as Porsche ref: 000 721 957 01)
Here is what you get....Details below...

A. VW Tools (4) Number T10057 Audi A4, A6, A8 and New Beetle
For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
If you have 4 slots VW AUDI this is the set (T10057) you need. This 4 piece set is extremely popular.
The 2 piece VW set is Number VW 3316 New Body Style Passat Jetta Golf . Virtually full coverage for Volkswagen Audi when you buy this set.

B. BMW Tools are one Pentagon shaped tool with a 3 5/8 inches overall length. Applicable: Most BMWs. This Five sided driver is used to release anti theft radio mounts. You will also get the special rare very small allen tool for BMW For newer BMW E38 & E39 7 SERIES

C. Mercedes Tools covers almost all newer and older vehicles, especially 1992 and newer 129, 140, 163, 202 & 210, Range Rover with Becker Nav System.
The MB Tools also work on Porsche. Appl: Turbo GT, GT2, GT3, Boxster, Cayenne 911, 996 , 987, Carrera etc.
Same as Porsche ref: 000 721 957 01 D. "U" Hooks for DIN Ford
Mercedes Ignition Turning Sleeve 41.50
Ignition Turning Sleeve M0045 Mercedes ref: 126 589 0714 00 This tool is perfect for the proper R&R of the protective cover for ignition / steering lock. Applicable: Mercedes chassis W123, W124, W126.
Diesel Injection Pump Socket 34.99
Diesel Injection Pump Socket Tool 32 Point Female Socket with 1/2" drive.
This socket is used for the R&R of delivery valve of diesel injection pump. Applicable: Mercedes diesel engines 601, 602, 603, 605, 606, 617, 1982 and up
Note mercedes ref 617 589 0109 00
Hazet Tools 32.50
4684 1 Mounting Hook : special steel, chrome plated, with T handle, plastic, black,
hook 40 mm, 9 offset, for rubber retainers of exhaust equipment:
FORD Fiesta, Orion, Escort, BMW etc.
Arbor 49.50
Arbor needed for the proper installation of oil seal on pulley side of crank shaft. Applicable: Mercedes engine M103, OM601, OM602, OM603. SAME AS BENZ 601 589 0314 00
Guide Rail Pin Puller for Mercedes 39.99
Mercedes Rail Pin Puller Guide
This Puller has an Overall Length of 85mm and is designed with a thrust bearing to ease the pulling action. Used for the proper extraction of rail pins from cylinder head. Especially useful in restricted spaces where other pullers and slide hammers will notfit. Comes with a 6mm extractor pin. Applicable: Mercedes M102, M110, M115, M116, M117, M130, OM601, OM602, OM603, OM615, OM616, OM617.

In the 4 cylinder and 6 cylinder engines, this tool also removes the timing chain tensioners pivot pin, which is hidden behind a bolt in the front right (facing forward) face of the cylinder head. It of course also removes all of the timing chain guide rail mount pins that are located in the left (facing forward) of the cylinder head, and down in the left face of the engine block. Extremely handy when doing jobs with the engine still in the car, such as headgasket replacement, timing chain tensioner replacement, or timing chain guide rail replacment. Works in all carbureted and fuel injected gasoline, and all diesel injected 4 cylinder and 6 cylinder engines as found in w108, w109, w110, w111, w112 chassis cars built in the 60s, as well as other models that use pins to secure guide rails.
Spark Plug Boot Puller 34.99
Spark Plug Metal Boot Remover Wrench
Newer Mercedes V 6 engines are equipped with a (2) spark plug wire and/or metal boot per cylindetr set up. This special wrench 17mm with its specific angle along its tapered machined surface of the box end allows it to fit into those metal spark plug boots after the coil pack has been removed. This special tool is the only good way to ensure that the metal boots and plug wires remain damage free during removal.
Overall length is 12.5 inches.
Steering Box Repair Kit 87.00
This Steering Box Repair Kit is needed for proper R&R of locking grooved nut and sector control piston. Applicable: Mercedes steering LS90
Spark Plug Boot Puller 34.99
Spark Plug Metal Boot Remover Wrench
Newer Mercedes V 6 engines are equipped with a (2) spark plug wire and/or metal boot per cylindetr set up. This special wrench 17mm with its specific angle along its tapered machined surface of the box end allows it to fit into those metal spark plug boots after the coil pack has been removed. This special tool is the only good way to ensure that the metal boots and plug wires remain damage free during removal.
Overall length is 12.5 inches.
Glow Plug Reamer 45.00
Pencil Type Reamer
Size 12 x 1.25 used for removing carbon buildup in Diesel Glow Plugs which is a major cause of glow plug failure.
Applicable: OM 601,615,616,and 617 , MB Ref: 901 589 0053 00.
722.6 Transmission Dipstick 26.50
Mercedes Transmission Dipstick Benz reference number 140 589 1521 00 For determining fluid level newer Mercedes with electronic transmission 722.6 The graduations on the fluid end (plastic dipping end) are: (Range) 25 (low) to 80 (high) The picture is not to scale.
Testimonial: The only way to properly fill/check correct fluid level on 722.6 Transmission. Mercedes has lowered the recommended service intervals of these transmissions which makes this dipstick a must have. For the most common Mercedes Transmissions. NC Technician/Shop Owner Robert Palmiter
Metal Clad Bushing Kit 289.00
Metal Clad Bushing R&R Kit M0079 Needed for the proper R R of Front Metal Clad rubber mount bushings of the rear axle carrier sub frame. This Tool has been ?Field Tested? and redesigned. Incorporating a thrust bearing for easy pulling / pushing action, reducing the wear & tear of the tool. This Bushing Tool comes complete with the proper components to get the job done right. Applicable: Chassis W 124, W 129, W 201, W 202, W 140
5 Piece Set with 65mm Wrench 79.00
Set 5 Tools for Mercedes repair.

1.Hub Securing Bar 113 0040 Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable:M112 & M113

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER

4. Long Pattern Thin wrench 36mm. Comes with rubber handle grip.

5. Thin Wrench 65mm with an 8mm overall thickness and an overall length of 16 inches for proper leverage. Mercedes ref: 120 589 0201 00.

You get all 5 tools with this purchase.
Injector Adaptor for Mercedes 52.50
Injector Adaptor for Mercedes Tool is used for checking the compression of diesel engines through the injector holes. Used in conjunction with a male fitting which has a 1/4" NPT. Applicable Mercedes Diesel engine models with 22 x 1.5mm injectors: OM602, OM603, OM604, OM605, OM606. NUMBER M0092
Oil Seal Arbor 52.00
Needed for the proper installation of oil seal on pulley side of crank shaft. Applicable: Mercedes engine M102
Puller Bracket Type 41.00
Mercedes Puller Bracket Type ITEM M0006 This tool is used for the proper extraction of steering pump pulleys. Applicable: Most Mercedes models.
Extractor plus Splined Socket 104.00
Set of 2 Tools
Extractor Tip Double Ended (Item M0046)
Used for the proper removal of prechamber from cylinder head.
Can be used in conjunction with a slide hammer.
Applicable: Mercedes engine OM601, OM602, OM603, OM604, OM615, OM616, OM617.
9Ref: number for this extractor is MB 902 589 0033 00)
Plus
Special Male Splined Socket with 1/2" drive.
Used for the proper R&R of threaded ring which secures prechamber in cylinder head.
Applicable: Mercedes 1990 up 602/603 engines with inclined injection, and all 604/605/606
Press Adapter Kit 156.35
Needed for the proper R&R of ball joints of the lower control arm. Used in conjunction with a hydraulic press. W124, W201
Mercedes Dash and Ignition Kit 17.50
MERCEDES DASH SERVICE TOOL KIT
Set Includes: Ignition "V" shape lock release wires same as Mercedes Number 900 589 0059 00
Plus a pair Long Hooks (overall length 6.5 inches)
(Similar to Mercedes 140 589 0223 00 the mercedes hooks are 7 inches the ones in this set are 6.5 inches)
You get the radio removal Keys (Pair)
Details:
Ignition Lock Removal (wires) Set for W124, 126, 201
Pair of Hooks for W107, 116, 123, 124, 126, 140, 201
Radio Removal keys FOR "1997 and OLDER" W129, 140, 202, 210
SLIDE HAMMER PIN PULLER 137.00
This set is used for extraction of rail pins from cylinder head while out of car. Impact Type Slide Hammer / Rail Pin Puller Comes complete with a set of 5 Extractor Pins This is an easy to hold, hand sized slide hammer. The Mercedes Number is 116 589 2033 00
Mercedes Valve Spring Compressor 149.00
M0068 Valve Spring Compressor Kit M0068 For 6 and 8 cylinder engines. Same as Benz Number 123 589 0361 00 Spring Compressor Kit used for R&R of valve spring or rocker arm. Job can be done with the cylinder head on or off the car. Applicable: M 114, 115, 116, 117, 123, 130, 180
Timing Chain set up Double Row 225.00
Master Link Timing Chain Tool Double Row Set up SAME AS BENZ NUMBER 000 589 5843 00 Used for proper assembly of timing chain master link. OM601, OM602, OM603, OM615, OM616, OM617

Single row adapter and/or KIT available.
The single row set up is the same price as this kit.....email...
Front Lower Control Arm Tools 174.50
Front Lower Control Arm Tools M0062 Press Kit needed for the proper installation of bushings into the front lower control arms. Applicable: Mercedes chassis W124, W129, W140. Each press washer has its own thrust bearing which eases the pressing action. This reduces friction, wear and tear of the tool, ensuring longevity.
On Sale Ignition Turning Sleeve 16.99
Ignition Turning Tool
For loosening and tightening the ring (rosette) of the electronic ignition switch.
Applicable: W129, 140, 202 (as of June 1, 1997), 208, 210, 211, 230, 240, 463
The Aluminum will not leave marks on the interior parts.
Benz ref: 210 589 0007 00
Spark Plug Wire Pliers 24.50
Spark Plug Wire Pliers
Used to remove the newer high voltage type wires
Wide grip section and special angle. makes it
easy to remove wires without separating crimps.
Applicable: 102, 103, 104, 110, 115, 116, 117, 119, 120
Same as Mercedes Tool Number 104 589 0037 00
also same as Zdmak item M104 0037X
Single Row Set up Only 225.00
Master Link Timing Chain Tool
Please read all:
Single Row Set up Only
Used for proper assembly of timing chain master link.
M102, M103 AND M116
Picture above is only for reference.
THE PICTURE ACTUALLY SHOWS THE DOUBLE,
BUT YOU WILL ONLY GET THE SINGLE ROW SET UP WITH THIS PURCHASE
Oil Seal Arbor 65.00
needed for the proper installation of oil seal on pulley side of crank shaft. Applicable: Mercedes engine M110, M114, M115, M116, M117, M130, M180, OM615, OM616, OM617
MB Master Valve Spring Compressor 271.00
Mercedes Valve Spring Compressor Kit M0069 MASTER Spring Compressor Kit used for R&R of valve spring or rocker arm. Job can be done with the cylinder head on or off the car. Applicable: Mercedes engine M102, M103.
4 Piece Set with 36mm Thin Wrench 75.00
Set 4 tools for Mercedes repair including:
1.Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.<

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER

4. Long Pattern Thin wrench 36mm.
You get all 4 tools with this purchase.
No Go Gauge 59.95
Mercedes
Go No Go Gauge* Used for checking hydraulic valve lifters Applicable: Mercedes V 8 engines 1976 and Newer * Excluding M119. Ref: 917 589 0623 00
Differential Sub Frame Kit 125.00
Mercedes Differential Sub Frame Kit M0074 Bushing Tool needed for R&R of differential sub frame bushings. This is the most efficient unit on the market. Each driver nut has its own thrust bearing which eases the pressing and pulling action. This reduces friction, wear and tear of the tool, ensuring longevity. Applicable: Mercedes chassis W124, W140, W201.

Call or email for lower price. Be sure to include a phone number in your email in case we need to call you back. We may have what we call "tool truck samples" or "scratch and dent" items just like this one or virtually brand new we may be able to sell at a lower price all depending upon inventory levels.
Feel free to call our toll free number 877 938 6657. Canada please email.
4 Piece Set with 32mm Thin Wrench 79.00
Set 4 tools for Mercedes repair (please note this set comes with a 32mm Long thin wrench)

1.Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER

4. Long Pattern Thin wrench 32mm.

You get all 4 tools with this purchase. Remember: this set has a 32mm open end long thin wrench).
3 Piece Fan / Hub Holding Set 69.50
Four Mercedes Tools *

1.Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER.
2 Piece Set 24.99
1.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

2.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER.
Mercedes Valve Tool Set 3 150.00
Mercedes Valve Adjustment Wrench Set of 3 Tools Made in Germany by Hazet This three piece set includes:Hazet Item Numbers 2769, 2769 1 and 2769 3
2 Piece Set 28.99
Wrench / Holding Bar Set of 2 Tools. This is similar to Benz Number 900 589 0307 00. Another old number for this item was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER.

2.Long Pattern Thin Wrench 36mm.
You get both tools with this purchase.
Ignition Pin Kit 19.99
Ignition Pin Kit M0059 Pins (2 pair) Needed for the proper removal of Ignition lock. Applicable: Chassis W124, W126, W201
Locking Nut 39.95
Locking Nut M0039 needed for securing the diesel injection pump cam shaft. Applicable:Mercedes OM601, OM602, OM603, OM605, OM606, OM617. Benz Ref: 601 589 0521 00
Hazet Tools 32.50
4684 2 Mounting hook 17 mm,
half round, 20 offset, e.g. for VW AUDI, MERCEDES BENZ
(except 190 type 201), OPEL and Asian cars etc.
Hazet 2769 Set 2 129.99
Hazet Mercedes Valve Adjustment Wrench Set of 2 Made in Germany This two piece set includes: Item Numbers 2769 and 2769 1 The 2769 is same as Benz Tool 601 589 0001 00 The 2769 1 is same as Benz Tool 421 589 0001 00
Hub Securing Bar Holder Set 39.99
Set 2 tools for Mercedes repair.
Including

1. Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.
2. Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER. You get both tools with this purchase.
Extractor Tip Double Ended 44.50
Extractor Tip Double Ended M0046 Used for the proper removal of prechamber from cylinder head. Used in conjunction with a slide hammer. Applicable: Mercedes engine OM601, OM602, OM603, OM604, OM615, OM616, OM617. Ref: 902 589 0033 00
Special Male Socket 59.50
Special Male Socket M0009 Male Splined Socket with 1/2" drive. Used for the proper R&R of threaded ring which secures prechamber in cylinder head. Applicable: Mercedes 1990 up 602/603 engines with inclined injection, and all 604/605/606 Ref: 604 589 0109 00
Pin Wrench Socket 85.50
M0007 Threaded Pin Wrench Socket This tool is used for the proper R&R of threaded ring which secures prechamber in cylinder head. The Mercedes number for this tool is 615 589 0007 00 Applicable: OM601/602/603 engines through 1989 with vertical injection. Also OM615, OM616, OM617 Ref: 615 589 0007 00
Pin Wrench Socket Plus Tip 137.50
Set 2 Tools with M0007 Plus M0046
Engine Oil Dipstick 49.00
Engine Oil Dipstick
Applicable 103. 104. 111 . 119 . 120, 136, 604, 605, 606, 611, 612, 613, 628,
The picture is for reference only.
Engine Oil Dipstick 39.50
Engine Oil Dipstick
The picture is for reference only NOT actual tool. This tool is about 3 ft long
Tool for measuring oil level also to check length of oil dipstick guide "pipe".
Please Note: While inserting this tool you should try to turn the dipstick carefully to allow for complete insertion.&nbsp;
Applicable: M112, 113, 271, 272, 642, 646, 647 &amp; 648
The dipstick is a special tool and it not supposed to stay in the car, when you bottom out the dipstick and read the level, when the procedure is complete and the level is where it supposed to be REMOVE the DIPSTICK and replace cap on dipstick tube.&nbsp;
My number for this item is MK 140 0110
THE MERCEDES REFERENCE FOR THIS ITEM SHOULD BE 120 0721
Set with Slide Hammer 79.00
Extractor Tip Double Ended M0046 Used for the proper removal of prechamber from cylinder head. Used in conjunction with a slide hammer. Applicable: Mercedes engine OM601, OM602, OM603, OM604, OM615, OM616, OM617. Ref: 902 589 0033 00
Plus
Slide Hammer use with Tool M0046 for proper removal of prechamber from cylinder head. Also other applications: Tool pulls dented sheet metal back into place. To use, drill a hole in the deepest part of the dent, insert the hook or self threading screw tip and tap lightly with the 2 1/2 lb slide hammer to remove the dent. A 15 inch long shaft enables high pulling force.
U Body 8mm Allen Socket 49.99
Special "U Shape" Body 8mm Allen Socket with 1/2 inch drive tool needed for the proper removal and replacement/torquing of cylinder head bolts under the rocker shaft. Applicable: Mercedes V 8 engines. Ref 916 589 0013 00
Hub Securing Bar Holder 29.99
ON SALE Hub Securing Bar
(Reference 113 589 0040 00)
Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.
Locking Hook 11.99
Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103. Mercedes ref: 103 589 0040 00
Allen Wrench Holding Bar 8 x 10 19.50
On Sale...
Allen Wrench Holding Bar
Comes complete with 8 and 10mm Allen bits.
The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606
The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 1986 and newer.
Ref 900 589 0307 00
2 Tools for Mercedes Repair 44.00
Set of 2 tools including:
Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench
PLUS 36mm Long Thin Wrench Removes lock nuts on thermo Viscous fan found on Mercedes also for a wide variety of applications on several different European vehicles.
You get both tools with this purchase.
Expansion Tank Adaptor 56.00
M0077 Expansion Tank Adaptor Used for pressurizing the liquid cooling system on models with a "male" threaded filler neck on expansion tank. Applicable: Mercedes E Class 96 and Newer.
Pin Wrench Socket Plus Tip 137.50
Set 2 Tools with M0007 Plus M0046
Special 29mm Socket 35.50
Special 29mm Socket M0010 This 29mm socket is used for proper R&R of transmission tail shaft retaining nut. 12 Point and special inside centering surfaces. 3/4 Drive. Model 190
Panel Popper Set of 5 16.50
DOOR PANEL & UPHOLSTERY TOOLS Complete Panel "Popper" Tool Set
Super Tools for Auto Interior Work
This 5 Piece Set of plastic pry pullers is perfect for working on those expensive panels on car interiors. It will also help work loose plastic decorative inserts, door moldings and countless other pieces on todays modern and many vintage cars.
* You may have seen other sets like this, but they only come with 4 pieces... This set has 5 pieces with more features plus the quality of this set is better (stronger and more durable) than other being sold,
making this a much better deal.
This set comes in a Clam Shell Protective Container.
722.6 Transmission Dipstick 26.50
Mercedes Transmission Dipstick Benz reference number 140 589 1521 00 For determining fluid level newer Mercedes with electronic transmission 722.6 The graduations on the fluid end (plastic dipping end) are: (Range) 25 (low) to 80 (high) The picture is not to scale.
Testimonial: The only way to properly fill/check correct fluid level on 722.6 Transmission. Mercedes has lowered the recommended service intervals of these transmissions which makes this dipstick a must have. For the most common Mercedes Transmissions. NC Technician/Shop Owner Robert Palmiter
TANK ADAPTER 19.99
Expansion Tank Adaptor VZ32 Applicable: ML Class 98 Newer Models with male threads on filler neck of expansion tank.
Thin Wrench 32 X 36mm 34.95
Thin Wrench Number 1032X36T Thin Wrench 32 X36mm with an 8mm overall thickness and an overall length of 12 inches for proper leverage. Many applications for this handy thin wrench
Cam Securing Pins 35.10
Securing Pins (Pair) M0083 Tools are used for the proper alignment of camshafts during R&R. Applicable: Mercedes Engine M 111, M 119. Mercedes ref: 111 589 0315 00
Ignition Pin Kit 19.99
Ignition Pin Kit M0059 Pins (2 pair) Needed for the proper removal of Ignition lock. Applicable: Chassis W124, W126, W201
Mercedes Hooks 23.00
Wire Pulling Hooks "Short Version" ITEM M0060 S Wire Hooks (Pair) short pattern needed for the proper removal of instrument cluster. Length of reach is 4.5 inches.
Spring Compressor Kit 224.00
Coil Spring Compressor Kit for Mercedes. For front and rear coil springs. Applicable: W107, W116, W123, W124, W126, W129, W140, W170, W201, W202, W208 and W210.
Comes with carrying case.
Compress front & rear axle springs on models with idler arm & some MacPherson type suspensions.
Same as 924 589 0231 00.
Telescopic range 120mm 325mm. You get 2 Plates sizes 90/150mm and 2 Plates size 70/130mm.
Oil Filter Wrench 74mm 13.99
Oil service Wrench 74mm with 14 Points (inside flats flutes).
This is an excellent deal. This tool has 2 bonus screws for more strength if needed.
The screws are kept in the holes at the top when not in use and can be used inserted into the side holes making the tool more effective.
Some applications include: Mercedes, Audi, VW Golf, and New body Jetta, TDI (Diesel) and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle. Mercedes M104, M110, M111, M119, M120 C, E etc...
Porsche 944 and 924. Some Toyota. Check your manuals for details and size needed. Measure filter diameter or canister diameter.
See chart below.
bullet Audi Coupe 81 87
bullet Audi Coupe Q 20v 90 91
bullet Audi Fox 73 79
bullet Audi 100 89 91
bullet Audi 100Q 89 91
bullet Audi 4000 4 Cyl 80 87
bullet Audi 4000 5 Cyl 80 81
bullet Audi 4000 Q 84 87
bullet Audi 5000 78 88
bullet Audi 5000 Q 87 88
bullet Audi 80 88 90
bullet Audi 90 88 90
bullet Audi 90 Q 20v 90 92
bullet BMW 325 85 88
bullet BMW 325e 84 88
bullet BMW 325es 86 87
bullet BMW 325i Sedan 87 91
bullet BMW 325i Cabriolet 87 93
bullet BMW 325is Coupe 87 91
bullet BMW 325ix 88 91
bullet BMW 525i 89 90
bullet BMW 528e 82 88
bullet Mercedes 190E 2.3 1985 1993
bullet Mercedes 190E 2.6 1987 1993
bullet Mercedes 260E 1987 1989
bullet Mercedes 300CE 1988 1989
bullet Mercedes 300E 2.6 1990 1992
bullet Mercedes 300E 1986 1992
bullet Mercedes 300E 4 Matic 1990 1993
bullet Mercedes 300SE 1988 1991
bullet Mercedes 300SEL 1988 1991
bullet Mercedes 300TE Wagon 1988 1992
bullet Mercedes 300TE 4 Matic Wagon 1990 1993
bullet Porsche 924 77 82
bullet Porsche 924 Turbo 80 82
bullet Porsche Cayenne S 03 04
bullet Porsche Cayenne Turbo 03 04
bullet Porsche 911/996 Carrera/2 98 04
bullet Porsche 911/996 Carrera/4 99 04
bullet Porsche 911/996 GT3 04 04
bullet Porsche 911 Twin Turbo 01 04
bullet Porsche Carrera GT 04 04
bullet Porsche Boxster 97 04
bullet Porsche 911 Turbo 1991 1994
bullet Porsche 924S 1986 1988
bullet Porsche 944 1983 1989
bullet Porsche 944S 1987 1988
bullet Porsche 944S2 1989 1991
bullet Porsche 944 Turbo 1986 1991
bullet Porsche 968 1992 1995
bullet Porsche 928 78 84
bullet Porsche 928 32 85 95V
bullet Porsche 911/993 Carrera/2 1995 1998
bullet Porsche 911/993 Carrera/4 1995 1998
bullet Porsche 911 Twin Turbo 1995 1999
bullet Volkswagen Dasher 74 81
bullet Volkswagen Fox 87 93
bullet Volkswagen Golf GL/GT 85 92
bullet Volkswagen Golf III GL 93 94
bullet Volkswagen Golf GTI 8/16V 85 92
bullet Volkswagen Golf III GTI 93 94
bullet Volkswagen Jetta 80 84
bullet Volkswagen Jetta GL 85 92
bullet Volkswagen Jetta(Canada) 93 99
bullet Volkswagen Jetta Carat 85 92
bullet Volkswagen Jetta III GL 93 94
bullet Volkswagen Jetta GLI 84 88
bullet Volkswagen Jetta GLI 16V
bullet Volkswagen Jetta III GLS
bullet Volkswagen Passat 16V 90 93
bullet Volkswagen Passat GL 95 97
bullet Volkswagen Quantum 4 Cyl 82 85
bullet Volkswagen Quantum 5 Cyl 83 88
bullet Volkswagen Rabbit 75 84
bullet Volkswagen Rabbit Convertible 79 87
bullet Volkswagen Rabbit Cabriolet 88 93
bullet Volkswagen Rabbit GTI 83 84
bullet Volkswagen Scirocco 75 88
bullet Volkswagen Scirocco 16V 86 88
bullet Volkswagen Van Water Cool 83 92
bullet Volkswagen Van Syncro 86 92 This tool can be used on the following filters
bullet Audi, VW: 070 115 561, 056 115 561G, 034 115 561A
bullet BMW: 11 42 1 266 773
bullet Mecedes: 102 184 01 01
bullet Porsche: 996 107 225 52, 993 207 201 02, 993 107 203 03, 928 107 201 05,
bullet 944 107 201 08
Puller Guide 42.00
Sliding Puller Guide needed for the proper extraction of rail pins from cylinder head. Comes equipped with a 5mm and 6mm extractor pin. SAME AS BENZ NUMBER 915 589 0733 00
Door Handlle Hinge Kit 36.50
Tool Kit for BENZ , VW , AUDI , PORSCHE door hinge/handle installer & remover.
Finally, a compact solution to accessing the special features found on the door hinges and door handles of VW/Audi, Mercedes Benz and Porsche, includes 4 door hinge bits (less than 1 inch long) with slender ratcheting wrench and extra long drivers for accessing Mercedes and VW door handle fasteners.
Spark Plug Wire Pliers 24.50
Spark Plug Wire Pliers
Used to remove the newer high voltage type wires
Wide grip section and special angle. makes it
easy to remove wires without separating crimps.
Applicable: 102, 103, 104, 110, 115, 116, 117, 119, 120
Same as Mercedes Tool Number 104 589 0037 00
also same as Zdmak item M104 0037X
Disc Brake Piston Reset Tool 38.75
Disc Brake Piston Reset Tool / Brake Press Tool
Very STURDY tool for the safe resetting of disc brake pistons on vehicles with fixed caliper disc brakes / for putting the pistons back into the housing.

TOOL IS APPROX 2 5/8" HEIGHT PLATE TO PLATE (top to bottom)
each plate is about 6.5mm thick
depth of tool front to back (inside) is 2 3/4 inches (69.85mm)

TESTIMONIAL:&nbsp;
When I attempted to replace the front brake pads on a 2001 Mercedes S430, I discovered that my old Piston Reset Tool (the one everyone has in their garage, sold everywhere under different brands for less than $10) just could not do the job. This is because the S430, like many other cars, has Dual Piston, Fixed Caliper brakes, which require a different Reset Tool (sometimes referred to as a Brake Pad Spreader).&nbsp;

When I went to Pep Boys, my salesman there told me that fixed calipers are a problem, and he did not have the tool for the job. I went to an independent parts store, which had a tool that had been hanging on their wall since 1979 (it looked like a miniature scissors jack with a long screw), but it could not have been inserted where it needed to be. NAPA had a catalog with a picture of something with a pistol grip on it that looked like it may or may not have worked. The Mercedes dealer can order a tool (MB 000 589 52 43 00) for $160 that looks like it could be used 1,000 times before it would come close to breaking or wearing out, which would be overkill; besides, it is huge and would take up too much room in my tool cabinet.

Bottom line: I had to buy a tool, and nobody stocks one, so I had to order something from somebody. I found the item number MK BRK J at ZDMAK for a very low price, and could see from the picture that it should work, so I ordered it. I am glad I did ? it arrived on time, and it worked perfectly!

Procedure was simple:&nbsp;
I took the cap off of the master cylinder under the hood, then jacked up the car and removed the wheels. The calipers remained bolted to the car throughout the procedure (of course, if I was replacing the rotors also, I think I would have had to remove the calipers). After removing the retaining pin and spring from behind the pads, I inserted the Reset Tool arms between the small exposed edges of the backing plates on the brake pads. Then I turned the handle on the tool and the arms pushed away from each other and started pushing the brake pads away from the rotor. Once there was more space I put the arms of the tool against the face of the pads themselves and pushed the pads (and pistons) all the way back. The tools job was done; I then slid the old pads out, slid the now ones in, reinstalled the spring and pins and I was done (after checking the fluid level and putting the cap back on the master cylinder).

I feel that I did receive a super tool which does the job perfectly and should last a DIY er a lifetime.&nbsp;
It does not take up too much space in the tool box,&nbsp;
and was also the least expensive option I found!&nbsp;

Steve M
Pennsylvania
XZN Triple Square Set 24.99
XZN Set of 4 "Triple Square" Tools.
This set includes sizes:
6mm, 8mm, 10mm & 12mm bits
Drive size is 3/8"
A very handy set for the German car Technician. You get all four (4) tools with this purchase.

Triple square, also known as a XZN socket, is a type of screw drive. They are commonly found on German vehicles such as BMW, Mercedes, and Volkswagen etc... These screws/fasteners are used in some high torque applications such as cylinder head bolts and drive train components. Triple square bolts are common to early Porsche and Volkswagen (CV) constant velocity joints. Increasingly, triple square screws are found on other European and Asian makes of cars. Other names for this type of triple square screws and drivers are "Double Hex", "Double Allen", and "Aircraft Screws". Despite this, "Double Hex" and "Double Allen" are misnomers. The recess in these bolts is actually (as the name suggests) made of three squares, not two hexagons. The corners are 90 degrees, not 120 degrees. They are not double hexes, and an Allen key will not fit them properly.

These are XZN Triple Square Tools. XZN means Triple Square or 12 point. If your tool book calls for XZN or Triple Square or 12 Point, these are probably the tools you need. Satin Chrome with New S2 Alloy Steel. These are some of the strongest drivers you will find.
Triple Square XZN Bit Set 9.99
12 Point (XZN) Bit Set
Set of 4
Metric (TRIPLE SQUARE) 12 Point Socket Bits.
Sizes: 6, 8, 10 and 12mm
Picture is for reference only. Each bit is 3 inches Long.
Heat treated alloy steel, sturdy 1/2 inch hex drive shaft.
Excellent for the German car Mechanic.
The German tool books use the term "XZN" to describe the 12 point style).
Dash and Ignition Kit 17.50
MERCEDES DASH SERVICE TOOL KIT
Set Includes: Ignition "V" shape Lock release Wires same as Mercedes Number 900 589 0059 00
Plus a pair Long Hooks (overall length 6.5 inches)
(Similar to Mercedes 140 589 0223 00 the mercedes hooks are 7 inches the ones in this set are 6.5 inches)
You get the radio removal Keys (Pair)
Details:
Ignition Lock Removal (wires) Set for W124, 126, 201
Pair of Hooks for W107, 116, 123, 124, 126, 140, 201
Radio Removal keys FOR "1997 and OLDER" W129, 140, 202, 210
Breaker Plug 9.99
Breaker Plug needed to stop current flow to the coil. This eliminates any chance of ignition while the engine is being turned over. This Breaker Plug is crucial when checking compression or adjusting valves. Applicable: Mercedes diagnostic plug. All models with electronic ignition. (Pin 4 & 5).
Brake Caliper Rewind Set 49.50
U.S./EURO/ASIAN/4WD VEHICLES
Disc Brake Pad & Caliper Service Tool Kit
Includes 8 adapters Magnetic socket adapter.
For brake assemblies
For rotating pistons back into caliper to provide clearance for new pads
Prevents damage to the piston and boot Designed for use with Mercedes, BMW, Volkswagen, GM, Audi, Ford, Honda, Subaru, Mazda, Nissan, Mitsubishi, Toyota, Land Rover and 4 wheel drive vehicles. Blow molded carryingcase for easy storage.
Ball Joint Tools 169.00
Ball Joint Tool This tool set is used for removing and installing the ball joint into the steering knuckle. Applicable: 211 E Class 2002 and newer. 215 CL Class 2002 and newer. 219 CLS 2006 and newer. 220 S Class 2000 and newer. 230 SL Class 2003 and newer (NOTE: THIS KIT IS THE SAME AS OTHER ITEM M220 0343)
Caliper Gauge 126.95
German Quality Caliper Gauge for Brake Disks for passenger cars and motorcycles. Measuring range 60 mm jaw 75 mm .
Allen Wrench Holding Bar 8 x 10 19.50
On Sale...
Allen Wrench Holding Bar
Comes complete with 8 and 10mm Allen bits.
The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606
The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 1986 and newer.
Ref 900 589 0307 00
Dial Guage Holder 79.50
Same as Mercedes number 102 589 0421 00. Dial Gauge Holder used for checking hydraulic valve lifters. To be used in conjunction with a dial indicator. Applicable: Mercedes engine M102, M103.
Spring Compressor Kit 224.00
Coil Spring Compressor Kit for Mercedes. For front and rear coil springs. Applicable: W107, W116, W123, W124, W126, W129, W140, W170, W201, W202, W208 and W210.
Comes with carrying case.
Compress front & rear axle springs on models with idler arm & some MacPherson type suspensions.
Same as 924 589 0231 00.
Telescopic range 120mm 325mm. You get 2 Plates sizes 90/150mm and 2 Plates size 70/130mm.
Valve Stem Seal Installer 9mm 32.00
Valve Stem Seal Installer Applicable: Mercedes engine M110, M114, M115, M116, M117, M130, M180, OM615, OM616
PLEASE NOTE: THIS INSTALL TOOL IS TEFLON TYPE SEALS ONLY.
Valve Stem Seal Installer 11mm 32.00
Valve Stem Seal Installer Applicable: Mercedes M110, M114, M115, M116, M117, M130, M180, OM615, OM616
PLEASE NOTE: THIS INSTALL TOOL IS TEFLON TYPE SEALS ONLY.
New Style Mercedes Oil Wrench 24.50
New Style Mercedes Oil Wrench 74mm with 14 Points (inside flats flutes).
Mercedes M102, M103 etc..
Check your manuals for details and size needed.(Measure filter diameter or canister diameter.
See ref number mb 103 589 0209 00
This is an excellent deal. Other applications include: Audi, VW Golf, and new body Jetta, TDI (Diesel) and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle.
Dash and Ignition Kit 17.50
MERCEDES DASH SERVICE TOOL KIT
Set Includes: Ignition "V" shape Lock release Wires same as Mercedes Number 900 589 0059 00
Plus a pair Long Hooks (overall length 6.5 inches)
(Similar to Mercedes 140 589 0223 00 the mercedes hooks are 7 inches the ones in this set are 6.5 inches)
You get the radio removal Keys (Pair)
Details:
Ignition Lock Removal (wires) Set for W124, 126, 201
Pair of Hooks for W107, 116, 123, 124, 126, 140, 201
Radio Removal keys FOR "1997 and OLDER" W129, 140, 202, 210
Hub Securing Bar Holder 29.99
ON SALE Hub Securing Bar
(Reference 113 589 0040 00)
Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.
65mm Thin Wrench 29.99
Thin Wrench 65mm with an 8mm overall thickness and an overall length of 16 inches for proper leverage. Mercedes ref: 120 589 0201 00
Hub Securing Bar Holder Set 39.99
Set 2 tools for Mercedes repair.
Including

1. Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.
2. Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER. You get both tools with this purchase.
2 Piece Set 28.99
Wrench / Holding Bar Set of 2 Tools. This is similar to Benz Number 900 589 0307 00. Another old number for this item was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER.

2.Long Pattern Thin Wrench 36mm.
You get both tools with this purchase.
2 Piece Set 24.99
1.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

2.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER.
Mercedes Oil Filter Wrench 13.99
Oil service Wrench 74mm with 14 Points (inside flats flutes).
This is an excellent deal. This tool has 2 bonus screws for more strength if needed.
The screws are kept in the holes at the top when not in use and can be used inserted into the side holes making the tool more effective.
Some applications include: Mercedes, Audi, VW Golf, and New body Jetta, TDI (Diesel) and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle. Mercedes M104, M110, M111, M119, M120 C, E etc...
Porsche 944 and 924. Some Toyota. Check your manuals for details and size needed. Measure filter diameter or canister diameter.
See chart below.
bullet Audi Coupe 81 87
bullet Audi Coupe Q 20v 90 91
bullet Audi Fox 73 79
bullet Audi 100 89 91
bullet Audi 100Q 89 91
bullet Audi 4000 4 Cyl 80 87
bullet Audi 4000 5 Cyl 80 81
bullet Audi 4000 Q 84 87
bullet Audi 5000 78 88
bullet Audi 5000 Q 87 88
bullet Audi 80 88 90
bullet Audi 90 88 90
bullet Audi 90 Q 20v 90 92
bullet BMW 325 85 88
bullet BMW 325e 84 88
bullet BMW 325es 86 87
bullet BMW 325i Sedan 87 91
bullet BMW 325i Cabriolet 87 93
bullet BMW 325is Coupe 87 91
bullet BMW 325ix 88 91
bullet BMW 525i 89 90
bullet BMW 528e 82 88
bullet Mercedes 190E 2.3 1985 1993
bullet Mercedes 190E 2.6 1987 1993
bullet Mercedes 260E 1987 1989
bullet Mercedes 300CE 1988 1989
bullet Mercedes 300E 2.6 1990 1992
bullet Mercedes 300E 1986 1992
bullet Mercedes 300E 4 Matic 1990 1993
bullet Mercedes 300SE 1988 1991
bullet Mercedes 300SEL 1988 1991
bullet Mercedes 300TE Wagon 1988 1992
bullet Mercedes 300TE 4 Matic Wagon 1990 1993
bullet Porsche 924 77 82
bullet Porsche 924 Turbo 80 82
bullet Porsche Cayenne S 03 04
bullet Porsche Cayenne Turbo 03 04
bullet Porsche 911/996 Carrera/2 98 04
bullet Porsche 911/996 Carrera/4 99 04
bullet Porsche 911/996 GT3 04 04
bullet Porsche 911 Twin Turbo 01 04
bullet Porsche Carrera GT 04 04
bullet Porsche Boxster 97 04
bullet Porsche 911 Turbo 1991 1994
bullet Porsche 924S 1986 1988
bullet Porsche 944 1983 1989
bullet Porsche 944S 1987 1988
bullet Porsche 944S2 1989 1991
bullet Porsche 944 Turbo 1986 1991
bullet Porsche 968 1992 1995
bullet Porsche 928 78 84
bullet Porsche 928 32 85 95V
bullet Porsche 911/993 Carrera/2 1995 1998
bullet Porsche 911/993 Carrera/4 1995 1998
bullet Porsche 911 Twin Turbo 1995 1999
bullet Volkswagen Dasher 74 81
bullet Volkswagen Fox 87 93
bullet Volkswagen Golf GL/GT 85 92
bullet Volkswagen Golf III GL 93 94
bullet Volkswagen Golf GTI 8/16V 85 92
bullet Volkswagen Golf III GTI 93 94
bullet Volkswagen Jetta 80 84
bullet Volkswagen Jetta GL 85 92
bullet Volkswagen Jetta(Canada) 93 99
bullet Volkswagen Jetta Carat 85 92
bullet Volkswagen Jetta III GL 93 94
bullet Volkswagen Jetta GLI 84 88
bullet Volkswagen Jetta GLI 16V
bullet Volkswagen Jetta III GLS
bullet Volkswagen Passat 16V 90 93
bullet Volkswagen Passat GL 95 97
bullet Volkswagen Quantum 4 Cyl 82 85
bullet Volkswagen Quantum 5 Cyl 83 88
bullet Volkswagen Rabbit 75 84
bullet Volkswagen Rabbit Convertible 79 87
bullet Volkswagen Rabbit Cabriolet 88 93
bullet Volkswagen Rabbit GTI 83 84
bullet Volkswagen Scirocco 75 88
bullet Volkswagen Scirocco 16V 86 88
bullet Volkswagen Van Water Cool 83 92
bullet Volkswagen Van Syncro 86 92 This tool can be used on the following filters
bullet Audi, VW: 070 115 561, 056 115 561G, 034 115 561A
bullet BMW: 11 42 1 266 773
bullet Mecedes: 102 184 01 01
bullet Porsche: 996 107 225 52, 993 207 201 02, 993 107 203 03, 928 107 201 05,
bullet 944 107 201 08
Flexible Shaft Hex Nut Driver 13.99
Flexible Hex Nut Driver
Sizes on this nut driver is 7mm
This is a great deal for a HEX NUT DRIVER Rubber coated flexible shaft.
Flex Nut Drivers work well on hose clamps, hex headed screws and nut screws.
Counter Holder 112 0040 74.50
Counter Holder Tool / Harmonic Balancer holder for the front crankshaft pulley Mercedes M112 and M113. This tool was redesigned to fit both versions of the Mercedes Benz pulley. 112,113,E320,ML320,CLK320,E430,ML430,C320,C43,E55 etc...
Similar to reference (tool) number 112 589 0040 00
C class from 1998 2005 with V 6 or V 8 engine
E class from 1998 2005 with V 6 or V 8 engine
SLK class from 1998 2005 with V 6 engine
CLK class from 1998 2005 with V 6 or V 8 engine
ML class from 1998 2005 with V 6 or V 8 engine
SL class from 1999 2006 with V 8 engine
S class from 2000 2005 with V 8 engine
G class from 2002 2007 with V 8 engine.
Pin Wrench Socket 44.95
Groovenut Socket 1/2 inch Drive
Ref: Same as 915 589 0207 00
This tool is used for R&R of grooved nut on rear axle shaft flange, necessary when replacing axle bearing or seal. Applicable: Mercedes chassis W107, W114 , W115 , W116 , W123 , W126. Models with constant velocity joint axles* Click here to see the Diagram on this Tool
2 Tools for Mercedes Repair 44.00
Set of 2 tools including:
Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench
PLUS 36mm Long Thin Wrench Removes lock nuts on thermo Viscous fan found on Mercedes also for a wide variety of applications on several different European vehicles.
You get both tools with this purchase.
Ignition Turning Sleeve 16.99
Ignition Turning Tool
For loosening and tightening the ring (rosette) of the electronic ignition switch.
Applicable: W129, 140, 202 (as of June 1, 1997), 208, 210, 211, 230, 240, 463
The Aluminum will not leave marks on the interior parts.
Benz ref: 210 589 0007 00
New Style Mercedes Oil Wrench 24.50
New Style Mercedes Oil Wrench 74mm with 14 Points (inside flats flutes).
Mercedes M102, M103 etc..
Check your manuals for details and size needed.(Measure filter diameter or canister diameter.
See ref number mb 103 589 0209 00
This is an excellent deal. Other applications include: Audi, VW Golf, and new body Jetta, TDI (Diesel) and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle.
German Car Special 2 Thin Wrenches 36.50
"Long" Pattern Thin Wrenches
Set of Two (2)
One of each size: 36MM and 32mm
Brand New "Long Thin Wrenches"
Many applications for these two tools,
especially for European cars.
Overall length of 15 inches.
Thickness of each wrench is 1/4" (6.35mm)
Some applications include: Mercedes and BMW R&R of fan clutch hub nut.
Porsche 32mm used for R&R of tie rods Model 911 Turbo, 89 76
36mm Needed for proper adjustment of rear ride height 911 , 89 77 etc...
Tie Rod Tool 35.50
Puller P266HX Separator used for disassembly of Pitman arm type tie rod ends without tearing the boots. Opening size is 18mm. Most VW Audi Late Porsche models.
Click here for a Diagram on this tool.
Hub Securing Bar Holder Set 39.99
Set 2 tools for Mercedes repair.
Including

1. Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.
2. Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER. You get both tools with this purchase.
Mini Nut Driver Set 26.95
8 Piece Set designed to aid the technician with work on hex nuts and bolts for Dasboards, Radios, ECU, Instrument panels, etc...This is a nice set for removal and replacement of small Hex (Allen) Fasteners. Quick Open End application and interchange. Adustable length for hard to reach areas. Comes in the plastic container. See images below. Tool in assembled position adusts from a minimum 5.5 inch to a maximum 9.0 inch overall. Hex sizes are: 3mm, 3.5, 4, 4.5, 5, 5.5 and 6mm See images below &nbsp; &nbsp; &nbsp; Click for Larger Image and more information &nbsp;
Mercedes Radio Removal Tools 8.99
Set of 2 Radio Removal Keys for Mercedes. Please note the rubber on the handle for a better grip. Used to remove the Radio, A/C and some Instrument clusters most MB models 124, 210, 163, 140, 208, 170, 202, 129, 201 Very easy to use. Simply slide into radio or a/c instrument cluster slots (two thin slots) on the lower portion left and right of your radio, A/C controller, instrument cluster or navigation unit. The tools snap in pull to remove in just seconds without damage to your radio, A/C, climate control, instrument cluster etc...S, C, E, SL, ML, SLK, CLK. Be sure to CLICK HERE for more RADIO TOOLS
Mercedes Timing Chain Tool 64.00
Timing Chain Tool Applicable: OM604, 605, 606 Holds timing chain against sprocket during installation, so the chain will not slip.
XZN Triple Square Set 24.99
XZN Set of 4 "Triple Square" Tools.
This set includes sizes:
6mm, 8mm, 10mm & 12mm bits
Drive size is 3/8"
A very handy set for the German car Technician. You get all four (4) tools with this purchase.

Triple square, also known as a XZN socket, is a type of screw drive. They are commonly found on German vehicles such as BMW, Mercedes, and Volkswagen etc... These screws/fasteners are used in some high torque applications such as cylinder head bolts and drive train components. Triple square bolts are common to early Porsche and Volkswagen (CV) constant velocity joints. Increasingly, triple square screws are found on other European and Asian makes of cars. Other names for this type of triple square screws and drivers are "Double Hex", "Double Allen", and "Aircraft Screws". Despite this, "Double Hex" and "Double Allen" are misnomers. The recess in these bolts is actually (as the name suggests) made of three squares, not two hexagons. The corners are 90 degrees, not 120 degrees. They are not double hexes, and an Allen key will not fit them properly.

These are XZN Triple Square Tools. XZN means Triple Square or 12 point. If your tool book calls for XZN or Triple Square or 12 Point, these are probably the tools you need. Satin Chrome with New S2 Alloy Steel. These are some of the strongest drivers you will find.
Heavy Duty 17mm Socket 19.95
Heavy Duty Allen 17mm Stubby Socket 1017 Heavy duty Allen socket designed specially for R&R of gearbox drain plugs. Also for a variety of other applications. 1/2 Drive Applicable: Most European Vehicles
Pressure Adaptor 24.95
Pressure Adaptor 1018 Used for pressuring the master cylinder or clutch slave cylinder reservoirs. Used in conjunction with a pressure bleeder. Comes with a 1/4 18 NPT threaded opening. Applicable:Most European models.
Thin Wrench 32mm Open End 32.00
Extra Long 32mm Thin Wrench Number 1032T This wrench has a thickness of 8mm. We have other 32mm thin wrenches on this website, but at 20 inches long and good quality, this is the wrench we recommend.
36mm Open End Thin Wrench 32.00
Extra Long 36mm Thin Wrench Number 1032T This wrench has a thickness of 8mm. We have other 32mm thin wrenches on this website, but at 20 inches long and good quality, this is the wrench we recommend.
Heavy Duty 8mm Allen 32.15
Multiple applications for this handy tool.
Super Duty 8mm Allen Item P243 Extra Long 3/8 Drive Socket This 8mm Extra Long Allen Socket is a solid one piece construction. Overall length is 7.75 inches. Used for R & R of some Benz Cylinder Headbolts,
Engine M116 , M117.
Valve Shim Plier 19.99
Valve Shim Tool Used for proper R&R of valve adjusting shims. Applicable: Overhead Cam engines with adjusting shims.
Special Open Socket 22mm 24.95
On Sale *
22mm Special Tube Socket
1.) Used for securing the Strut tower retaining nut of most European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench)
2.) R&R of Oxygen Sensor.
Also for R&R of some Mercedes Diesel injectors ( OM604, 605 & 606).
Details: For removing and installing front strut unit on VW Golf up to 1988, Jetta up to 87, Scirocco, Audi 80 and Golf 3 from 1993 newer, Passat from 88 and newer, Audi 100, 200 Coupe and Quatro.
This tool is often used in conjunction with a 7mm hex wrench.
Click here for a picture of the tools in action:
Special Crowsfoot Socket 23.50
OXYGEN SENSOR Socket 4491b This is a Special 22mm Crowsfoot Socket with 3/8 Drive Used for the removal and replacement of Oxygen Sensor that are situated within a confined area. No need to snip the wires leading to the unit when all you want to do is check the sensor. Applicable: Most European Models.
Special Socket 19.99
OXYGEN SENSOR Socket 4491C 22mm Socket 3/8 Dr. used for the removal and replacement of stubborn Oxygen Sensors situated within a confined area. Applicable: Most European Models.
Top Dead Center Indicator 13.50
Top Dead Center Indicator 9710 Used for T.D.C. on any Gas engine. Simply unscrew a spark plug and twist the rubber hose part of this tool into the spark plug hole. As you rotate the engine with a turning bar, the piston forces air through the whistle part of this tool. Once the whistling stops the engine is at T.D.C.
Extra Long Pliers 17.95
"Extra Long" Valve Stem Seal Pliers
You will not see these every day, or find a better price on this tool anywhere! These are longer than the standard Valve Pliers. Tool is used for the proper extraction of hard to get at stem seals. The inside grooves on the tips of this Plier allows the firm grip of both O.E. and aftermarket seals Applicable: Overhead Cam engines.
Mercedes Valve Spring Compressor 183.00
Valve Spring Compressor Kit M0067 used for R&R of valve spring or rocker arm. Job can be done with the cylinder head on or off the car. Applicable: Mercedes engine M110. 6 cylinder engines with dual cam shafts.
MB Master Valve Spring Compressor 271.00
Mercedes Valve Spring Compressor Kit M0069 MASTER Spring Compressor Kit used for R&R of valve spring or rocker arm. Job can be done with the cylinder head on or off the car. Applicable: Mercedes engine M102, M103.
Valve Stem Seal Installer 9mm 32.00
Valve Stem Seal Installer Applicable: Mercedes engine M110, M114, M115, M116, M117, M130, M180, OM615, OM616
PLEASE NOTE: THIS INSTALL TOOL IS TEFLON TYPE SEALS ONLY.
Valve Stem Seal Installer 11mm 32.00
Valve Stem Seal Installer Applicable: Mercedes M110, M114, M115, M116, M117, M130, M180, OM615, OM616
PLEASE NOTE: THIS INSTALL TOOL IS TEFLON TYPE SEALS ONLY.
Flexible 3 Piece Driver Set 22.50
3 Piece Flex Hex Nut Driver Set.
Flexible Shaft Nut Drivers are Great for the German car mechanic, great for working on hose clamps, hex headed screws and nut screws.
Sizes included in this set are 6mm, 7mm and 8mm.
You will get all three tools with this purchase.
Excellent for the Professional or Shadetree Technician!
Support Bridge 59.50
Support Bridge M0072 Same as Mercedes Tool 102 589 0359 00 This Tool should be used in conjunction with Depressor Foot M 0071 and Valve Spring Compressor Kit M0069.
Flexible Shaft Hex Nut Driver 13.99
Flexible Hex Nut Driver
Size on this nut driver is 6mm
This is a great deal for a HEX NUT DRIVER Rubber coated flexible shaft.
Flex Nut Drivers work well on hose clamps, hex headed screws and nut screws.
Depressor Foot Mercedes 35.25
Depressor Foot M0071 Needed for compressing valve springs. Used in conjunction with Valve Spring Compressor Kit M 0069. Applicable: Mercedes model 190E 2.3L with 16 valves.
Flexible Shaft Hex Nut Driver 13.99
Flexible Hex Nut Driver
Sizes on this nut driver is 7mm
This is a great deal for a HEX NUT DRIVER Rubber coated flexible shaft.
Flex Nut Drivers work well on hose clamps, hex headed screws and nut screws.
Flexible Shaft Hex Nut Driver 13.99
Flexible Hex Nut Driver
Sizes on this nut driver is 8mm
This is a great deal for a HEX NUT DRIVER Rubber coated flexible shaft.
Flex Nut Drivers work well on hose clamps, hex headed screws and nut screws.
Dial Guage Holder 79.50
Same as Mercedes number 102 589 0421 00. Dial Gauge Holder used for checking hydraulic valve lifters. To be used in conjunction with a dial indicator. Applicable: Mercedes engine M102, M103.
722.6 Transmission Dipstick 26.50
Mercedes Transmission Dipstick Benz reference number 140 589 1521 00 For determining fluid level newer Mercedes with electronic transmission 722.6 The graduations on the fluid end (plastic dipping end) are: (Range) 25 (low) to 80 (high) The picture is not to scale.
Testimonial: The only way to properly fill/check correct fluid level on 722.6 Transmission. Mercedes has lowered the recommended service intervals of these transmissions which makes this dipstick a must have. For the most common Mercedes Transmissions. NC Technician/Shop Owner Robert Palmiter
Steering Box Repair Kit 87.00
This Steering Box Repair Kit is needed for proper R&R of locking grooved nut and sector control piston. Applicable: Mercedes steering LS90
Pin Wrench Socket 47.50
Pin Wrench Socket M0030 Picture not to scale Pin Wrench Socket with 1/2" drive. Used for R&R of grooved nut on drive pinion shaft flange of differential. Applicable: Mercedes swing axle types. The Mercedes Ref: 111 589 0507 00. Click here to see the Diagram on this Tool
Pin Wrench Socket 56.50
M0029 Pin Wrench Socket Pin Wrench with 1/2" drive, needed for R&R of grooved nut on transmission drive shaft flange. Applicable: Mercedes transmission K4A 025. Click here to see the Diagram on this Tool
Pin Wrench Socket 59.99
M0032 Pin Wrench Socket with 1/2" drive, needed for R&R of grooved nut on transmission drive shaft flange. Applicable: Mercedes transmission K4C 025, W4B 025, K4A 040 Click here to see the Diagram on this Tool
Pin Wrench Socket 36.50
M0028 Pin Wrench Socket With 1/2" drive, needed for R&R of grooved nut on front differential counter shaft. Applicable: Mercedes Transmission G76/18, G76/18A, G76/18C, G76/27, G76/27A, G76/27 5. Click here to see the Diagram on this Tool
Pin Wrench Socket 59.80
M0026 Pin Wrench Socket with 1/2" drive, needed for R&R of grooved nut on drive pinion shaft flange of differential. Applicable: Mercedes chassis W107, W114, W115, W116, W123, W126. Models with constant velocity joint axles. Click here to see the Diagram on this Tool
Torx Set 15.99
Torx Tamperproof Set with 1/4 Drive and 3/8 Drive sizes.
11 Pieces, sizes included: (3/8 drive) T40, T45, T50, T55 and T60.
(1/4 Drive) T10, T15, T20, T25, T27 and T30.
Slide Hammer 29.00
Slide Hammer use with Tool M0046 for proper removal of prechamber from cylinder head. Also other applications: Tool pulls dented sheet metal back into place. To use, drill a hole in the deepest part of the dent, insert the hook or self threading screw tip and tap lightly with the 2 1/2 lb slide hammer to remove the dent. A 13 long shaft enables high pulling force. Slide hammer has 1/2 13 UNC thread.
Injector Adaptor for Mercedes 52.50
Injector Adaptor for Mercedes Tool is used for checking the compression of diesel engines through the injector holes. Used in conjunction with a male fitting which has a 1/4" NPT. Applicable Mercedes Diesel engine models with 22 x 1.5mm injectors: OM602, OM603, OM604, OM605, OM606. NUMBER M0092
Breaker Plug 9.99
Breaker Plug needed to stop current flow to the coil. This eliminates any chance of ignition while the engine is being turned over. This Breaker Plug is crucial when checking compression or adjusting valves. Applicable: Mercedes diagnostic plug. All models with electronic ignition. (Pin 4 & 5).
Extractor Tip 23.50
Used for pulling chain tensioners. Used in conjunction with a slide hammer. Applicable:Mercedes engine M110.
Seal Guide 31.00
Needed to prevent damage to the seal during installation of timing cover with seal already in place. Applicable: Mercedes engine M104, M103 03/1989 and newer
Seal Guide 31.00
Needed to prevent damage to the seal during installation of timing cover with seal already in place. Applicable: Mercedes engine M103 0 2/?89 and older. SAME AS BENZ TOOL 103 589 0014 00
Puller Bracket Type 41.00
Mercedes Puller Bracket Type ITEM M0006 This tool is used for the proper extraction of steering pump pulleys. Applicable: Most Mercedes models.
Puller (Collet Type) 175.00
Used for the proper removal of spacer ring from the pulley side of crank shaft. Applicable: Mercedes engine M102, M110, M114, M115, M116, M117, M130, M180, OM615, OM616, OM617. SAME AS BENZ 102 589 0033 00
Oil Seal Arbor 52.00
Needed for the proper installation of oil seal on pulley side of crank shaft. Applicable: Mercedes engine M102
Oil Seal Arbor 65.00
needed for the proper installation of oil seal on pulley side of crank shaft. Applicable: Mercedes engine M110, M114, M115, M116, M117, M130, M180, OM615, OM616, OM617
Press Adapter Kit 156.35
Needed for the proper R&R of ball joints of the lower control arm. Used in conjunction with a hydraulic press. W124, W201
Press kit 143.00
Press Kit M0078 Needed to properly compress the brake band piston cover in order for R&R of the locking ring. Applicable: All Models.
202 210 Rubber Mount 00
Rubber Mount Set
Applicable: W202, 210
For removing or installing the rear rubber hydraulic mount
in the Lower Control Arm (Lower/under wishbone) on the car.
(Kit including the Hydraulic Pump)
Hazet Oil Service Tool 29.50
Oil service Wrench 74mm with 14 Points (inside flats flutes).
THIS ITEM HAS BOTH DRIVE SIZES 3/8" (10mm)
AND OUTSIDE HEX SIZE = 27mm
Some applications include: Mercedes, Audi, VW Golf,
and new body Jetta, TDI (Diesel) and the following gas vehicles;
Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle.
Mercedes M104, M110, M111, M119, M120 C, E
Porsche 944 and 924.
Some Toyota (Filter 08922 0211 etc...)
Can also be used on BMW Top of housing 1.9L M44
Super High Quality Original Factory Tool Made in Germany!
Click here to see a detailed Application Chart Measure filter diameter canister diameter or Check your manuals for details and size needed.
On Off Ratio Tester 399.00
Discontinued. Tester Appl: 1980 93
For checking On/Off Ratio and testing C.O. levels, including late model 100/100IR settings.
Mercedes Valve Wrench 66.50
Valve Wrench 17mm for Mercedes M110
Made in Germany by Hazet!
M110 engines (6 cylinder with dual camshafts).
Tensioner 24.95
Chain Tensioner (Rigid), Used for the proper R&R of cam shaft and its housing while checking and adjusting cam shaft timing. Applicable: Mercedes engine M110. SAME AS BENZ TOOL 110 589 0331 00
Valve Guide Installer 11mm 41.25
Applicable: Mercedes V 8 engines
Valve Guide Installer 10mm 41.25
Applicable:Mercedes engine OM615, OM616, OM617.
Valve Guide Installer 9mm 41.25
Applicable: Mercedes engines with new modified valve guides.
Valve Guide Installer 9mm 41.25
Pictures of Valve Guides are for reference only Applicable: Mercedes engine M102
Puller Guide 42.00
Sliding Puller Guide needed for the proper extraction of rail pins from cylinder head. Comes equipped with a 5mm and 6mm extractor pin. SAME AS BENZ NUMBER 915 589 0733 00
Clutch Piston Assembly Sleeve 127.60mm 39.50
Needed for installing the clutch piston into the external disc carrier on transmission 722.4 722.1 722.3
Clutch Piston Assembly Sleeve 135mm 39.95
Needed for installing the clutch piston into the external disc carrier on transmission 722.4 722.1 722.3
Clutch Piston Assembly Sleeve 111.70mm 39.50
Needed for installing the clutch piston into the external disc carrier on transmission 722.4 722.1 722.3
Mercedes Timing Chain Tool 155.00
Timing Chain Tool Applicable: M119 Holds timing chain against sprocket during installation, so the chain will not slip.
Mercedes Timing Chain Tool 93.99
Timing Chain Tool Applicable: M102 Holds timing chain against sprocket during installation, so the chain will not slip.
Mercedes Fan Holder 65.00
M603 0040 Bracing tool for fastening fan hub. Fan Holder Appl.: M119, OM602, 603, 604, 605, 606, 611.
LED Tester 53.99
NUMBER VAG1527B LED Tester Factory Tool VAG1527B Special Tool for diagnostic troubleshooting. 3 to 48V range.
Socket Holders 3 Metal 7.99
Socket Holders 3
These Holders are for Sizes; 1/4 inch, 3/8 and 1/2 inch Sockets.
Panel Popper Set of 5 16.50
DOOR PANEL & UPHOLSTERY TOOLS Complete Panel "Popper" Tool Set
Super Tools for Auto Interior Work
This 5 Piece Set of plastic pry pullers is perfect for working on those expensive panels on car interiors. It will also help work loose plastic decorative inserts, door moldings and countless other pieces on todays modern and many vintage cars.
* You may have seen other sets like this, but they only come with 4 pieces... This set has 5 pieces with more features plus the quality of this set is better (stronger and more durable) than other being sold,
making this a much better deal.
This set comes in a Clam Shell Protective Container.
Mercedes Special Tool 47.50
Special Tool for MERCEDES Star.
Chrome plated, with T handle made of black plastic, for mounting and removing the Mercedes Star at the engine hood
on class S (W 140), E (W 124 since model 93) and C (W 202)
Crowsfoot Valve Tool 89.99
Rare and hard to find 17mm Crowsfoot For valve adjustment. Drive 12.5 = 1/2 Inch with an Overall Length 125mm. High Quality Tool Made in Germany
Counter Holder 112 0040 74.50
Counter Holder Tool Harmonic Balancer holder for the front crankshaft pulley Mercedes M112 and M113. This tool was redesigned to fit both versions of the Mercedes Benz pulley. 112,113,E320,ML320,CLK320,E430,ML430,C320,C43,E55 etc...
Similar to reference (tool) number 112 589 0040 00
C class from 1998 2005 with V 6 or V 8 engine
E class from 1998 2005 with V 6 or V 8 engine
SLK class from 1998 2005 with V 6 engine
CLK class from 1998 2005 with V 6 or V 8 engine
ML class from 1998 2005 with V 6 or V 8 engine
SL class from 1999 2006 with V 8 engine
S class from 2000 2005 with V 8 engine
G class from 2002 2007 with V 8 engine.
Glow Plug Reamer 45.00
Pencil Type Reamer
Size 12 x 1.25 used for removing carbon buildup in Diesel Glow Plugs which is a major cause of glow plug failure.
Applicable: OM 601, 615, 616, and 617 , MB Ref: 901 589 0053 00.
Metric Deep Sockets 13.99
9 Piece 3/8? Drive
Deep Socket Set (metric)
Heat treated alloy steel, Drop forged for strength.
Polished chrome plated finish.
10mm 21mm
Socket rail for storage.
242 VW Gearbox Bearing Kit 650.00
242 MASTER KIT IS COMPRISED OF OVER 13 COMPONENTS
Designed to GRAB HOLD of the INNER RACE OF BEARING like an EAGLE CLAW, when no other surfaces are exposed. Extraction of the bearing is accomplished by rotating the center bolt of 242 Body until the steel ball tip bottoms out on a protruding shaft or blind hole. The 242 Body along with the Extractor Collet and bearing to be extracted, all secured firmly together, work their way up the center press bolt.


THE EAGLE CLAW OF BEARING EXTRACTOR!!!
THE EXTENSION TUBES ALLOWS YOU TO REACH OVER EXTRA LONG SHAFTS!!!
THE ONLY SOLUTION WHEN NO OTHER EXTRACTOR CAN GRAB HOLD OF THE BEARING SURFACE!!!

Gearboxes, Transmissions, Transaxles, Transfer Cases, Wheel Bearing Housing of European, several Asain and Domestic vehicles. International Bearing Numbers: 6204, 6205, 6206, 6304, 6305, 6306. Available as O.E. or replacements from SKF, NSK, FAG, etc., (Federal Mogul, Torrington drop the first digit).

Application Chart:
Part Fingered Collet Collet Range Grabs hold of inner race O.D.
242 A 8 44.50 41.50mm
242 B 7 37.00 35.00mm
242 C 7 41.00 38.50mm
242 E 8 40.50 38.50mm
242 F 9 42.50 40.50mm
242 G 7 43.50 41.00mm
242 H 7 32.00 30.00mm
242 I 7 48.00 45.50mm
Arbor 49.50
Arbor needed for the proper installation of oil seal on pulley side of crank shaft. Applicable: Mercedes engine M103, OM601, OM602, OM603. SAME AS BENZ 601 589 0314 00
2 Piece Set 28.99
Wrench / Holding Bar Set of 2 Tools. This is similar to Benz Number 900 589 0307 00. Another old number for this item was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER.

2.Long Pattern Thin Wrench 36mm.
You get both tools with this purchase.
2 Piece Set 29.99
Set 2 tools for Mercedes repair.
1.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

2.Long Pattern Thin Wrench 32mm.
3 Piece Fan / Hub Holding Set 69.50
Four Mercedes Tools *

1.Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER.
4 Piece Set with 32mm Thin Wrench 79.00
Set 4 tools for Mercedes repair (please note this set comes with a 32mm Long thin wrench)

1.Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER

4. Long Pattern Thin wrench 32mm.

You get all 4 tools with this purchase. Remember: this set has a 32mm open end long thin wrench).
4 Piece Set with 36mm Thin Wrench 75.00
Set 4 tools for Mercedes repair including:
1.Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.<

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER

4. Long Pattern Thin wrench 36mm.
You get all 4 tools with this purchase.
5 Piece Set with 2 Long Wrenches 79.00
Five Tools for Mercedes Repair

Including:
1.Hub Securing Bar (Reference 113 589 0040 00) Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable: M112 & M113, 119.986 (1996 and newer). Should be used in conjunction with a 36mm thin open end wrench.

2.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Another old number for this was 117 589 0307 Comes complete with 8 and 10mm Allen bits. The 8mm is needed for R&R of fan clutch fastener Applicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606 The 10mm bit is for adjusting A/C belt tension and R&R of idler pulley Models 420, 560 with V 8 19 86 and NEWER

4. Long Pattern Thin wrench 32mm. Comes with rubber handle grip.

5. Long Pattern Thin wrench 36mm.

You get all 5 tools with this purchase.
Hazet Deep Offset 8 Pc Metric Set 169.50
This is an eight piece Deep Offset Wrench set Double Box wrenches with 12 points.Sizes: 6x7mm, 8x9, 10x11, 12x13, 14x15, 16x17, 18x19 and 21x22mm.
Super High Quality Tools Made in Germany by Hazet!<
Hex Socket 19mm 19.85
This is a 19mm Hex Socket 1/2 Drive.
World Famous Hazet Sockets Made in Germany!
Hazet Tools 32.50
4684 1 Mounting Hook : special steel, chrome plated, with T handle, plastic, black,
hook 40 mm, 9 offset, for rubber retainers of exhaust equipment:
FORD Fiesta, Orion, Escort, BMW etc.
Hazet Tools 32.50
4684 2 Mounting hook 17 mm,
half round, 20 offset, e.g. for VW AUDI, MERCEDES BENZ
(except 190 type 201), OPEL and Asian cars etc.
36mm Oil Filter Wrench 39.99
BMW MINI COOPER TOOL Mercedes Benz diesel oil filter wrench.
This is the same as Mercedes item 606 589 01 09 00. Works on BMW and Mercedes
This tool is 6 point size 36mm shallow socket 3/8" drive.
Heavy duty construction. It is made by Hazet for Mercedes and BMW.
Good for engine OM606 used in 1995 W124 E300 diesel, 96 97 W210 E300 diesel,
and 1998 E300 turbodiesel. Also for MB Diesel Engines OM604, OM605
and BMW Mini, BMW M52 6 Cyl., M60 8 cyl., M70 12 cyl and Volkswagen VR6.
Some other applications include:
Mercedes diesel engines: OM604, OM605, OM606 1995 W124 E300 diesel,
1996 97 W210 E300 diesel, 1998 E300 turbo diesel.
BMW Mini Cooper, BMW M52 6 cyl, BMW M60 8 cyl, BMW M70 12 cyl.
VW Volkswagen VR6
Ford Truck 6.0L 2003 thru 2004

High Quality Hazet Tool Made in Germany!
Spark Plug Boot Puller 34.99
Spark Plug Metal Boot Remover Wrench
Newer Mercedes V 6 engines are equipped with a (2) spark plug wire and/or metal boot per cylindetr set up. This special wrench 17mm with its specific angle along its tapered machined surface of the box end allows it to fit into those metal spark plug boots after the coil pack has been removed. This special tool is the only good way to ensure that the metal boots and plug wires remain damage free during removal.
Overall length is 12.5 inches.
Fuel Tool Mercedes Benz 39.50
Cup Wrench for Mercedes W202. Used to remove fuel sender retainer.
Ball Joint Separator (24mm) 69.99
Ball Joint Separator (24mm)
For splitting track rod ends, anti roll bar mountings, ball joints, etc..
especially in confined areas. Applicable: VW Audi, BMW, Ford, Opel, Mitsubishi...Mercedes W170 W202 W210 W220.
Mercedes Transmission Tool 149.50
Assembly Device
Appl.: Trans. 722.1, 722.3, 722.4, 722.5
This tool compresses the brake band piston cover in order to easily remove the locking ring.
Mercedes Rubber Mount Set 320.00
Rubber Mount Set Applicable: W208
For removing or installing the rear rubber hydraulic mount in the Lower Control Arm. (mechanical type)
Mercedes Assembly Fixture 169.00
Assembly Fixture Appl.:Trans. 722.3, 722.4, 722.5
Mercedes Holder Set 69.00
Camshaft Holding Plate Set Appl.:M112, 113
Holds camshaft in 40 degree TDC position (left/right side)
Ball Hex Long Pattern 12.50
Long Pattern
9 Piece Ball Type Hex Key Set
Sizes 1.5mm thru 10mm
Set with Slide Hammer 79.00
Extractor Tip Double Ended M0046 Used for the proper removal of prechamber from cylinder head. Used in conjunction with a slide hammer. Applicable: Mercedes engine OM601, OM602, OM603, OM604, OM615, OM616, OM617. Ref: 902 589 0033 00
Plus
Slide Hammer use with Tool M0046 for proper removal of prechamber from cylinder head. Also other applications: Tool pulls dented sheet metal back into place. To use, drill a hole in the deepest part of the dent, insert the hook or self threading screw tip and tap lightly with the 2 1/2 lb slide hammer to remove the dent. A 15 inch long shaft enables high pulling force.
Radio Removal Set 21.50
This is the best price set on the market...Bar None! The competition does NOT offer this COVERAGE for the price they charge.
This is a Master Set and it is used with BMW, Mercedes, Volkswagen Audi, Porsche and DIN.
FULL COVERAGE on Volkswagen Audi.
What makes this set better is a total of 8 keys for VW Audi and two for BMW plus the grips on the keys are coated for easy use.
You will notice a total of 3 different sets for Volkswagen Audi, two different tools for BMW and a set for newer Mercedes that will also work with older Mercedes and also works with some Porsche. (Same as Porsche ref: 000 721 957 01)
Here is what you get....Details below...

A. VW Tools (4) Number T10057 Audi A4, A6, A8 and New Beetle
For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
If you have 4 slots VW AUDI this is the set (T10057) you need. This 4 piece set is extremely popular.
The 2 piece VW set is Number VW 3316 New Body Style Passat Jetta Golf . Virtually full coverage for Volkswagen Audi when you buy this set.

B. BMW Tools are one Pentagon shaped tool with a 3 5/8 inches overall length. Applicable: Most BMWs. This Five sided driver is used to release anti theft radio mounts. You will also get the special rare very small allen tool for BMW For newer BMW E38 & E39 7 SERIES

C. Mercedes Tools covers almost all newer and older vehicles, especially 1992 and newer 129, 140, 163, 202 & 210, Range Rover with Becker Nav System.
The MB Tools also work on Porsche. Appl: Turbo GT, GT2, GT3, Boxster, Cayenne 911, 996 , 987, Carrera etc.
Same as Porsche ref: 000 721 957 01 D. "U" Hooks for DIN Ford
German Car Special 2 Thin Wrenches 36.50
"Long" Pattern Thin Wrenches
Set of Two (2)
One of each size: 36MM and 32mm
Brand New "Long Thin Wrenches"
Many applications for these two tools,
especially for European cars.
Overall length of 15 inches.
Thickness of each wrench is 1/4" (6.35mm)
Some applications include: Mercedes and BMW R&R of fan clutch hub nut.
Porsche 32mm used for R&R of tie rods Model 911 Turbo, 89 76
36mm Needed for proper adjustment of rear ride height 911 , 89 77 etc...
65mm Thin Wrench 29.99
Thin Wrench 65mm with an 8mm overall thickness and an overall length of 16 inches for proper leverage. Mercedes ref: 120 589 0201 00
32mm Open End Thin Wrench 19.99
32mm Open End Thin Wrench Long Pattern Thin Wrench with an overall length of 15 inches. The thickness of this wrench is 1/4" (6.35mm). Some applications include: Mercedes and BMW R&R of fan clutch hub nut. Porsche 32mm used for R&R of tie rods Model 911 Turbo 1976 89 etc... This is a great tool for working on European and Asian vehicles.
36mm Open End Thin Wrench 19.99
Long 36mm Thin Wrench
ON SALE
SHOCK ABSORBER TOOL 219.99
W220 SHOCK ABSORBER SERVICE TOOL KIT
For changing the top seal in air suspension strut.
Fix suspension strut to a vise.
Set 3 legs onto stub bolts in strut.
Drive the contour forcing screw to compress the seal cup and &12288;replace the seal.
Application : Benz W220
Blind Hole Bearing Tool Set 249.00

ST9006 8 Pc. Blind Hole Bearing / Bushing Collet Set with Slide Hammer Features & Benefits:
1 slide Hammer Shaft
1 Hammer
8 Collets; Size Range = mm (SAE)
8 10 (5/16 13/32), 10 12 (13/32 15/32),
12 14 (15/32 9/16), 15 17 (19/32 15/16)
17 20 (11/16 25/32), 20 24 (25/32 15/16),
25 29 (1 1 1/8), 30 32 (1 3/16 1 1/4)

Holding Tool 8 x 10 14.50
Mercedes Fan Belt Service * Special Fan Idler Pulley Tensioner Tool Allen Wrench / Holding Bar with 8mm and 10mm HEX BITS ZDM MBT8X10
Steering Pump Puller 76.00
Collet Type Puller used for the proper extraction ofpulleys
LS 75, LS 85, LS 90
Ref tool number 108 589 0233 00
Injection Nozzle Socket 89.95
Injection Nozzle Socket for Mercedes Benztype 202 and 210 engines 604, 605, 606 (with window)
22mm Socket overall length is 110mm
Drive size 1/2 inch.
Reference tool number 606 589 0009 00
This is a super high quality original factory tool made in Germany!
Bushing Kit W140 298.00
This special kit was designed for the crucial task of damage free R&R of front lower control arm, metal clad/ rubber mount bushings. The beauty of this job specific kit is its on the car application which allows the technician to tackle the repair without the need for an hydraulic press. Applicable: Mercedes chassis W140
Bushing Kit W210 298.00
This special kit was designed for the crucial task of damage free R&R of front lower control arm, metal clad/ rubber mount bushings. The beauty of this job specific kit is its on the car application which allows the technician to tackle the repair without the need for an hydraulic press. Applicable: Mercedes chassis W210
Bushing Kit W202 298.00
This special kit was designed for the crucial task of damage free R&R of front lower control arm, metal clad/ rubber mount bushings. The beauty of this job specific kit is its on the car application which allows the technician to tackle the repair without the need for an hydraulic press. Applicable: Mercedes chassis W202
Assembly Fixture 722.3 , 722.4 279.50
Sleeve for installing reverse gear piston in front cover 722.3
Plus assembly device for brake band piston b1
and assembly fixture for circlip on spring brake retainer of clutch k1 and k2 Applicable 722.3 and 722.4
Bushing Extractor 150.00
Mercedes Bushing extractor for replacement of diff mounting metalastic bushings found in rear sub frame. Applicable W124 and W201
Engine Oil Dipstick 39.50
Engine Oil Dipstick
The picture is for reference only NOT actual tool. This tool is about 3 ft long
Tool for measuring oil level also to check length of oil dipstick guide "pipe".
Please Note: While inserting this tool you should try to turn the dipstick carefully to allow for complete insertion.&nbsp;
Applicable: M112, 113, 271, 272, 642, 646, 647 &amp; 648
The dipstick is a special tool and it not supposed to stay in the car, when you bottom out the dipstick and read the level, when the procedure is complete and the level is where it supposed to be REMOVE the DIPSTICK and replace cap on dipstick tube.&nbsp;
My number for this item is MK 140 0110
THE MERCEDES REFERENCE FOR THIS ITEM SHOULD BE 120 0721
Engine Oil Dipstick 49.00
Engine Oil Dipstick
Applicable 103. 104. 111 . 119 . 120, 136, 604, 605, 606, 611, 612, 613, 628,
The picture is for reference only.
3 Spark Plug Tools 23.99
Set of 3 Spark Plug Tools Including: Extra Long 5/8 (16mm) Spark Plug Socket Overall Length is 4 1/2 inches 3/8 Drive. Plus one of each 5/8 and 13/16 Flexible Spark Plug Sockets 3/8 Drive 6 Point with Neoprene insert. Excellent for the professional or shadetree mechanic.
7 Pc Adapter Set 14.99
Includes: 1/4", 3/8", and 1/2" U Joint style adapters.
Plus adapters 3/8" to 1/4", 1/4" to 3/8" , 1/2" to 3/8", and 3/8" to 1/2" drive adapters.
Mercedes Wheel Drill Jig 189.00
This is a MERCEDES DRILL JIG
If you have ever tried to pull out a broken lug nut from a Mercedes Benz wheel, You know how hard it is, or how hard it was. With this Jig this problem is no longer a concern. Only a couple of minutes and your troubles are over. The Solution: This Mercedes Drill Jig. Applicable: All Mercedes.
Deep Offset Wrench Set 110.00
Deep Offset Box Wrench Set
8 Piece set sizes included:
6 x 7mm
8 x 9mm
10 x 11mm
12 x 13mm
14 x 15mm
16 x 17mm
18 x 19mm
20 x 22mm
12 point ring spanners. Satin chrome, made of high performance forged steel.
Polished head and ring. High Quality Tool Set Made in Germany!
Magnetic Sparkplug Sockets 13.99
Set of 2 Magnetic Sparkplug Sockets 3/8 drive
Included are sizes: 16mm (5/8) and 21mm (13/16).
Remote Starter 13.99
Remote Starter Switch
Heavy gauge, rubber covered copper wire, a tough, smooth working, reliable switch.
Depress button to jog or start the engine.
STUBBY SCREWDRIVERS 7.99
This is a multi purpose tool...
With a 1/4 Drive Male and Female handle,
also included are number 1 and 2 Phillips Bits Plus a special split toothed bit for dashboard screws
3 Way Hex Driver 0.00
Great for those hardto reach Hex screws.
Made of industrial quality hardened steel,
and vinyl coated for comfort and a stable grip.
Ball head Bondhus style Hex wrenches work at an
angle of up to 25 degrees.
This wrench combines three hex sizes: 4, 5, and 6mm.
Easy to use "Y" shape for convenience and extra leverage.
Cam Holding Wrench Kit 39.50
Cam Holding Wrench Kit Holds camshaft in 40 degree TDC position (left/right side) 32mm Appl.: 1998 and newer Mercedes Benz with V6 and V8 engines (M112, M113) 38mm special wrench for turning the cam. This special Cam Securing Master Wrench Kit has all the necessary components to properly adjust and lock the cams into position. Comes as shown with (1) Cam Wrench and (2) Cam Alignment Plates

Application Detail:&nbsp;
M112 V 6 Engine
19982005 C240
19982004 CLK240
19982004 E240
19982004 C320
19982004 E320
19982005 S320
19982003 ML320
19982004 CLK320
19982003 SLK320
20032008 Chrysler Crossfire
20012003 C32 AMG
20012003 SLK32 AMG
20052006 Chrysler Crossfire SRT 6
20032005 ML350
20032005 S350

M113 V 8 Engine
1998 2003 CLK430
1998 2002 E430
1999 2001 ML430
1998 2000 C43 AMG
1999 2006 S430
2001 2006 CL500
2002 2006 CLK500
2003 2006 E500
2002 2008 G500
1999 2006 S500
1999 2006 SL500
2001 2006 ML500
2001 2002 CL55 AMG
1998 2002 CLK55 AMG
1998 2002 E55 AMG
2001 2003 ML55 AMG
2001 2003 S55 AMG
2002 2003 G55 AMG
2004 2008 SLK55 AMG
2005 2007 C55 AMG
2002 2006 CL55 AMG
2002 2006 S55 AMG
2002 2006 SL55 AMG
2004 2006 E55 AMG
2004 2008 G55 AMG
Mercedes Filter Wrench 24.50
BRAND NEW STYLE
MERCEDES BENZ OIL FILTER WRENCH (74MM*14POINTS) FOR LATE MODEL MERCEDES VEHICLES.
T Handle Brake Hook 8.99
T Handle Brake Tool for mounting and dismounting the spring of brake shoes on vehicles with rear disk brakes.
100 Piece Bit Set 15.99
100 Piece Security Bits Set: Contains many of the most common tamperproof type security bit sizes,
including torx bits, spanner bits, hex bits, tri wing bits, and special XZN bits. Includes items below...

1 wing nut driver.

1 magnetic bit holder.

1 socket bit holder.

1 1/4" sq. x 1/4" hex x 1" extension.

1 1/4" sq. x 1/4" hex x 2" extension.

3 clutch bits ( 1, 2 & 3)

3 torq bits ( 6, 8 & 10)

3 XZN (spline) bits (M5, M6 & M8)

4 tri wing bits ( 1, 2, 3 & 4)

4 square recess bits ( 0, 1, 2 & 3)

4 spanner bits ( 4, 6, 8 & 10)

6 metric hex tamper proof bits (2, 2.5, 3, 4, 5 & 6)

6 SAE hex tamper proof bits (5/64, 3/32, 7/64, 1/8, 9/64 & 5/32)

8 phillips bits (0, 1, 2{5} & 3)

8 pozi drive bits (0, 1, 2{5} & 3)

9 slotted bits (3, 4, 4.5, 5, 5.5, 6, 6.5, 7 & 8)

9 metric hex bits (1.5, 2, 2.5, 3, 4, 5, 5.5, 6 & 8mm)

9 torx bits (T 8, 10, 15, 20, 25, 27, 30, 35 & 40)

9 torx tamper proof bits (T 8, 10, 15, 20, 25, 27, 30, 35 & 40)

10 SAE hex bits (1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32 & 1/4)
For the German Car mechanic this set is worth the price because of the Torx and XZN (spline) bits (XZN sizes 5mm, 6mm and 8mm) these three small XZN bits are very hard to find in this short pattern.
You can see these 3 bits on the right hand side second row from the bottom.

Comes complete as shown with (indexed) storage / carry case.

Radio Removal Set 21.50
This is the best price set on the market...Bar None! The competition does NOT offer this COVERAGE for the price they charge.
This is a Master Set and it is used with BMW, Mercedes, Volkswagen Audi, Porsche and DIN.
FULL COVERAGE on Volkswagen Audi.
What makes this set better is a total of 8 keys for VW Audi and two for BMW plus the grips on the keys are coated for easy use.
You will notice a total of 3 different sets for Volkswagen Audi, two different tools for BMW and a set for newer Mercedes that will also work with older Mercedes and also works with some Porsche. (Same as Porsche ref: 000 721 957 01)
Here is what you get....Details below...

A. VW Tools (4) Number T10057 Audi A4, A6, A8 and New Beetle
For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
If you have 4 slots VW AUDI this is the set (T10057) you need. This 4 piece set is extremely popular.
The 2 piece VW set is Number VW 3316 New Body Style Passat Jetta Golf . Virtually full coverage for Volkswagen Audi when you buy this set.

B. BMW Tools are one Pentagon shaped tool with a 3 5/8 inches overall length. Applicable: Most BMWs. This Five sided driver is used to release anti theft radio mounts. You will also get the special rare very small allen tool for BMW (upper left) For newer BMW E38 & E39 7 SERIES

C. Mercedes Tools covers almost all newer and older vehicles, especially 1992 and newer 129, 140, 163, 202 & 210, Range Rover with Becker Nav System.
The MB Tools also work on Porsche. Appl: Turbo GT, GT2, GT3, Boxster, Cayenne 911, 996 , 987, Carrera etc.
Same as Porsche ref: 000 721 957 01 D. "U" Hooks for DIN Ford
Benz Transmission Tool 38.95
Transmission Linkage Bushing Installer / Tool for Mercedes Benz with automatic transmissions, virtually all later models, some Ford and other vehicles needing this tool to easily and safely push TOUGH nylon bushings into place. Works on different bushing sizes. The design of this tool was initiated by a long time Mercedes Benz Master Technician&nbsp;
with 26 years of experience and the tool has recently been modified and perfected. We are the FIRST to bring this tool to the world wide web...... Zdmak Special Tools for the serious auto technician!
T50 Torx with U Joint 14.99
Torx size T50 Universal Joint Special Tool used for oil pump 129, 163, 208 and 210. Satin Chrome plated 3/8 drive.
5 Point Star Bit Set 15.99
SECURITY TORX PLUS BIT SET
5 Point Star Security TORX PLUS Insert Bit Set with Mini Ratchet
5 Point set includes sizes TS10, 15, 20, 25, 27, 30, 40
Please note there are 10 total bits and only 7 actual sizes you will get each of the sizes above plus the kit has an extra size 25, 30 and 40 because the 25, 30 and 40 are the popular sizes and tend to wear out (or get lost) faster than the other sizes.
These are Security Torx Plus Tools and they Do NOT work in a standard Torx Fasteners.
Reminder: These are 5 point tools AND THEY ARE TAMPERPROOF VERY RARE AND HARD TO FIND SET!
You will get both the bit set and the mini ratchet with this purchase.

Torx, Torx Plus and Camcar are registered trademarks of Textron, Inc. Torx plus is designed to allow greater torque, and to minimize wear.
Universal Puller 39.99
Universal Puller More convenient than standard pullers. Versatile and easy to use 5 Ton Straight Puller More convenient than standard pullers. For Gears and for Pulleys etc...Versatile and easy to use. 9" bar. (3) pairs of puller arms included. Puller arms slide back and forth. Chrome plated straight bar puller set in a plastic carrying case. It is easy to use and has multiple applications. Includes:
1 each Carry Case
2 each cap screw jaws, 3" reach
2 each wide jaws, 5" reach
2 each narrow jaws, 5" reach
1 each 9 3/4" forcing screw
1 each 10" 2 way crossarm
Hazet Flexible Nut Driver 44.50
Best Quality 6mm Flexible Shaft Nut Driver with ergonomically shaped handle.
For Hose clamps, radiator hoses and many other fastener applications.
World Class Hazet Tools Made in Germany!
Hazet Flexible Nut Driver 44.50
Best Quality 7mm Flexible Shaft Nut Driver with ergonomically shaped handle.
For Hose clamps, radiator hoses and many other fastener applications.
World Class Hazet Tools Made in Germany!
7mm Brake Bleeding Wrench 9mm 28.50
High Quality Brake Bleeding wrench 7mm. Made in Germany by Hazet.
9mm Brake Bleeding Wrench 28.50
High Quality Brake Bleeding wrench 9mm. Made in Germany by Hazet.
11mm Brake Bleeding Wrench 29.50
High Quality Brake Bleeding wrench 11mm. Made in Germany by Hazet.
Extra Long Torx Driver 19.50
T20 Torx, with 10 inch Long Pattern Screwdriver.
For work on engine, dash, doors and body.
World Class Hazet Tools Made in Germany!
Extra Long Torx 20.50
T25 Torx
Extra Long Driver
10 inch Long Pattern.
For work on engine,
dash, doors and body.
World Class Hazet Tools
Made in Germany!
Extra Long Torx Driver 22.99
T30 Torx, with 10 inch Long Pattern Screwdriver.
For work on engine, dash, doors and body.
World Class Hazet Tools Made in Germany!
Magnetic Spark Plug Socket 13/16 56.98
3/8 Drive Magnetic Spark Plug Socket 13/16.(20.8)
World Class Hazet Tools Made in Germany!
Magnetic Spark Plug Socket 5/8 56.50
This Tool Number is 880AMGT.
3/8 Drive Magnetic Spark Plug Socket 5/8. (16.0)
World Class Hazet Tools Made in Germany!
Universal Joint Torx Sockets 00
880 G E/4 Universal Joint Torx Sockets Female TORX Socket Set
Sizes E8, E10, E12 and E14. Drive nominal size 10 = 3/8 inch.
Reversible Ratchet / T Handle 47.99
Combination Reversing Ratchet with Quick Release Button and T Handle 1/4 Drive.
Great for strong or sensitive work. Can be used with Hazet Extension 868 (not included.
Quality Tools Made in Germany!
5mm Ball Tip Hex Socket 21.50
5mm Ball Tip Hex Socket 3/8 Drive. Overall Length is 116mm.
Super High Quality Tools Made in Germany!
8mm Ball Tip Hex Socket 22.00
8mm Ball Tip Hex Socket 3/8 Drive. Overall Length is 116mm.
Super High Quality Tools Made in Germany!
9mm Ball Tip Hex Socket 22.00
9mm Ball Tip Hex Socket 3/8 Drive. Overall Length is 116mm. Super High Quality Tools Made in Germany!
Hex Socket 12mm 22.50
This is a 12mm Hex Socket 1/2 Drive. World Famous Hazet Sockets Super High Quality Tools Made in Germany!
Hex Socket 14mm 22.50
14mm Hex Socket 1/2 Drive.
World Famous Hazet Sockets Made in Germany!
Gearbox Hex 17mm Socket 24.99
This is a 17mm Hex Socket
1/2 Drive.
World Famous Hazet Sockets Made in Germany!
1/2 Drive, 17mm heavy duty allen socket for R&R of gear box drain plugs.
41mm Socket 3/4 Drive 54.99
Hazet 41mm Socket 6 Point 3/4 Drive size with locking Pin.
World Class Hazet Tools Made in Germany!
36mm Socket 3/4 Drive 46.95
Big Hazet 36mm Socket 6 Point 3/4 Drive size with locking Pin.
World Class Hazet Tools Made in Germany!
For R&R of axle nut Applicable: BMW E38 and E39 with 36mm 12 point axle nut
27mm Oil Filter Wrench 35.99
HAZET NUMBER 2169 27
square drive nominal size 10 = 3/8, resp. outside hexagon 27 mm 14 point s 74.4 mm
32mm Oil Filter Wrench 35.99
2169 32 Oil Filter Wrench, steel grey, square drive nominal size 10mm = 3/8, resp.
outside hexagon 27 mm 14 point s 74.4 mm 6 point s 32 mm OPEL Astra, Corsa, VW Passat, AUDI

Buy seperately or buy in a set of 3 sizes 27, 32 and 36mm.

Bonus Torx Set 26.00
Torx Bonus Set Including Screwdriver Set 7 Pc. Sizes included: T8, T10, T15, T20, T25, T27 & T30.
Torx (6 Point) heads used for a wide variety of applications and a wide variety of vehicles. Please note: The screwdrivers are not tamperproof they are standard torx. The folding unit and ratchet at the bottom of the picture are both tamperproof. The Fold up tool has Tamperproof Torx tips. Each torx blade has a hole in the tip = Tamperproof) The sizes are: T9, T10, T15, T20, T25, T27, T30, T40 Some applications include: The T25 for use on E34 E32 E36 E39 E38 (tilt slide sunroof). The T30 is for most BMW with supplemental restraint systems / SRS (BMW REF 002110). The T20 is for some applications on E38 (Diffusion Disc Mount).
Torx Combo Mini Bit and Ratchet Set The seven bits on the left side of the bit holer are Torx Tamperproof Plus this set has 1 and 2 Phillips bits, and a flat head bit. The Tamperproof Torx sizes are: T10, T15, T20, T25, T30, T40 for Volkswagen, Audi,Volvo, Mercedes and BMW applications.
You will get all of the tools shown here with this purchase.
Bonus Torx and Star Set 18.99
Check it out....SECURITY TORX BONUS SET Here is what you get: 5 Point Star Security TORX PLUS Insert Bit Set with Mini Ratchet The 5 Point set includes sizes TS10, 15, 20, 25, 27, 30, 40 Please note there are 10 total bits and only 7 actual sizes in the 5 POINT set you will get each of the sizes mentioned above plus the 5 POINT kit has extra (spare) sizes 25, 30 and 40 the popular sizes tend to wear out or get lost faster. These are 5 point Security Torx Plus Tools and they Do NOT work in a standard Torx Fasteners. (see set below) . Very rare and hard to find a set like this with both types of bits.

The 6 POINT TORX SET includes mainly Tamperproof Torx. The seven bits on the left side are tamperproof, plus this set includes a number 1 and number 2 Phillips and a flat head bit. The Torx sizes in this set are: T10, T15, T20, T25, T30, T40 The bits in this set are also tamperproof. Torx, Torx Plus and Camcar are registered trademarks of Textron, Inc. Torx and Star bits are designed to allow greater torque, and to minimize wear.

You will get all items shown here including 2 sets of bits and two Mini ratchets with this purchase.
Seal Remover Puller 11.50
TOOL VW681 Seal Remover Puller For grease seals and oil seals. The two tips will fit many applications.
Windshield Washer Aiming Tool 19.99
Nozzle Adjusting Tool Made in Germany by Hazet
Telescopic handle with magnetic head 6 mm , adjusting needle, guard cap and pocket clip, for adjusting the nozzles of the washing system. The telescopic handle can be used to demonstrate the jet of the nozzles to the window. Be sure to click on the Link below for more pictures of this tool.. Click here to see more images of this Hazet tool...
5 Point Mirror Tool Rare 28.50
Special 5 Point Tool Made in Germany by Hazet. Rare and Hard to find Star pattern 5 Point Tamperproof driver for Removing and Installing the exterior Mirror on Type 211 (E CLASS) as well as Type 203 (C CLASS). High quality tool made in Germany. Lenth of shaft is 200mm and the overall length is 225mm.
Please note: standard torx is 6 point. This tool is 5 point.
Hose Clamp Plier 29.99
Hose Clamp Pliers Allows for extra reach, removal and locking of clamps into open position Allows for removal of plastic and/or metal self tightening hose clamps with diameters of 11/16" 2 1/2" (18mm 54mm) Precision clamp on end of flexible cable allows for extended reach where other models cannot reach Pliers can be locked, freeing up your hands and making your job easier and faster Pliers have a lifetime warranty Well made Plier with heavy gauge steel, operates in a smooth, consistent manner. Nice ratcheting design. Lets you stop the constriction anywhere from none to fully clamped. To release, you squeeze, and hit the thumb switch. The thumb switch is easy to operate. The main spring loaded mechanism is a safety pin type of spring, does not offer a lot of resistance, which makes releasing it easy. The cable unit attaches to the pliers at the top, where a coil of metal keeps the pressure off of the cable when storing. The gripper end is angled which is great for smaller diameter clamps, but on larger ones, it tends to grip on the edge instead of on the flat portion of the gripper mechanism. Not a big deal works fine either way. This Plier relies on a long coil spring at the gripper end to move the gripper to the fully opened position
More pictures of this tool Click Here
Female Torx Set 15.99
10 Piece Torx Female Socket Set
3/8 Drive and 1/4 Drive assortment on a rail.
1/4 Drive Sizes are: E4, E5, E6, E7, E8. 3/8 Drive Sizes are: E10, E12, E14, E16, E18.
Excellent for the professional or shadetree mechanic!
Two Torx Sets 26.99
Two Torx Sets Special Deal
MALE & FEMALE SETS
Male Tamperproof Torx (6 POINT)
Set with 1/4 Drive and 3/8 Drive sizes.
11 Pieces, sizes included: (3/8 drive) T40, T45, T50, T55 and T60.
(1/4 Drive) T10, T15, T20, T25, T27 and T30. Plus you will get the ten piece Female Set
Description: 10 Piece Torx Female Socket Set
3/8 Drive and 1/4 Drive assorted sockets on a rail.
The (smaller) 1/4 Drive Sizes are: E4, E5, E6, E7, E8.
The (larger) 3/8 Drive Sizes are: E10, E12, E14, E16, E18.
36mm Oil Filter Wrench 15.99
Special 36mm Oil Filter Wrench Removes and installs filters on BMW Mini Cooper. The low profile socket fits 36mm fuel and oil filters. The low profile socket works in confined spaces. 3/8 in. drive Not for use with an impact wrench.
BMW Mini Cooper, BMW M52 6 cylinder, BMW M60 8 cylinder, BMW M70 12 cylinder.
Mercedes Benz diesel engines: OM604, OM605, OM606 (1995 W124 E300 diesel, 96 97 W210 E300 diesel, 1998 E300 turbodiesel).
Same as Mercedes tool number: 606 589 01 09 00VW Volkswagen VR6
Also for Ford Truck 6.0L 03 04
Extra Long Boot Plier 29.99
Extra Long Spark Plug Wire Pliers Rare and hard to find at this price. Used to remove the newer high voltage type wires Wide grip section and special extra long pattern makes it easy to remove wires without separating crimps. Applicable: 102, 103, 104, 110, 115, 116, 117, 119, 120 Similar to Mercedes Tool Number 104 0037 except this tool is much longer.
Ball Joint Tool Set 69.50
Set of two tools
First tool (top of image) pictured is a Universal tool is used to separate the ball joint from the spindle support arm. It works on many domestic and import front wheel drive vehicles, and is adjustable for diffrent size ball joints. Using the correct ball joint tool makes a tough job much easier. Factory ball joints are pressed in tight, if you damage the ball joint, the situation gets ugly. Two Stage Ball joint tool Special steel, galvanized, for removing the ball pivots of steering arms, stabilizers etc.
Plus Universal Ball joint Puller (18 22mm opening), light series, galvanized Specifications Once the puller is positioned on the pin by adjusting the central screw, the joint is removed by turning the side screw. You get both tools with this purchase.
Ball Joint Puller 18 22mm 34.50
Ball Joint Puller / Universal (18 22mm opening) Ball Joint Tool, galvanized. Once the puller is positioned on the pin by adjusting the central screw, the joint is removed by turning the side screw. It works on many domestic and import vehicles, and is adjustable for different size ball joints. Using the correct ball joint tool makes a tough job much easier. Factory ball joints are pressed in tight, if you damage the ball joint, the situation gets ugly. Read more about this tool and for more pictures of this tool in action Click Here
Universal Ball Joint Separator 37.00
Universal Ball Joint Tool used to separate the ball joint from the spindle support arm.
It works on many domestic and import front wheel drive vehicles, and is adjustable for different size ball joints.
Using the correct ball joint tool makes a tough job much easier.
Factory ball joints are pressed in tight, if you damage the ball joint, the situation gets ugly.
Two Stage Ball joint tool Special steel, galvanized, for removing the ball pivots of steering arms, stabilizers etc...
Read more about this item below.

UNIVERSAL BALL JOINT TOOL
Basic tools required for the job (aside from a good strong jack and stand)
18mm wrench, socket, ratchet, pry bar, ball joint tool (same as 3287a) and penetrating oil.

&nbsp;

Span of the Jaw is about 20mm side to side and stage one opening is about 30mm and stage two opening is about 50mm
up and down.
Step One: Once you have safely jacked and secured the car, and removed the tire, using your 18mm box end wrench, remove the nut on the ball joint end. It may require some penetrant, and a little force. Long pattern wrenches are good for jobs like this.
You get a lot more leverage, and dont end up using pipes, or cheaters, etc..
This makes it possible to remove the joint without wanting to pull out the BFH, for which there is little room to give a good swing anyway. Give it about 1/2 turn and the SHOULD joint pop out. Next step: is to remove the bolt that holds the inside on. Both sides are 18mm. An easy way is to use a shallow socket to turn the bolt, holding the nut with the wrench. Or use an 18mm deep offset wrench, which would&nbsp;work just fine. The nut usually sits quite deep in the subframe. Once you get the nut off, you need to get the bolt out. The factory service manual says to lower the subframe at the rear to get the bolt out. You dont absolutely have to
What you end up doing however is wiggling the bolt out, sliding it under the fuel lines a little. It is not easy, but it is easier than lowering the subframe in many cases.
If you were to lower the subframe, you may need an alignment.
might consider getting one, as you never know how much you may have changed the toe or camber by replacing a control arm but there is a little bit of play in the pivot, and you never know exactly where it was when you started.
Getting the bolt to slide back into the new arm for some reason was not as hard as taking it out of the old one. Be VERY careful with the fuel lines (passenger side) or brake lines (driver side). You will need to (somehow) preload the suspension before you can torque the bolt on the inner end. You might use a hydraulic bottle jack on a concrete block to push up on the bottom of the stud for the front lower control arm. (Your floor jack might be a good idea too) Jack it till it starts to lift the car off of your stand a tiny little bit. Be very careful The jack could slip, which would cause the suspension to slam down. If your head was in the way, it MAY leave a mark. (Torque the bolt to APPROX. 66 lb/ft +1/4 turn) Torque the ball joint nut to APPROX. 74 lb/ft. You may need to hold the stud with an allen wrench, to keep it from turning while you start the nut on. Author: Kris Hansen

(Volkswagen Audi People: tool is Similar to 3287a)&nbsp;

10 Piece Metric Hex Set 29.99
10 Piece 3/8? Drive Metric Hex Bit Socket Set
Heat treated Chrome Vanadium steel construction.
Sizes are: 2, 3, 4, 5, 5.5, 6, 7, 8, 9 & 10mm
Set comes on a rail as shown.
Excellent for the German car lover!
Mercedes Overflow Device 21.50
Pipe with Nipple For adjusting fuel delivery on diesel engines Overflow pipe for injection pump for adjusting the start of delivery according to the low pressure overflow method.
Set 2 Alternator Tools 23.50
Combination Socket Set of 2 consisting of the 19mm Multi Spline (short socket) and XZN (longer 12 point socket) size M10 for mounting and dismounting the alternator pulley. Volkswagen Audi Mercedes Porsche etc...For mounting the V belt pulley (slip clutch pulley) at the alternator (some older manuals call it a generator), especially for T.D.I. VW Golf III, Vento, Passat and AUDI A 3.
The short serrated socket (3400) is size 19mm outside diameter and Length is 30mm.
The larger tool is M10 XZN triple square and is 3/8 drive x 4 inch length. See repair Group 27 (Porsche Bulletins) Boxster Alternators with free wheeling Pulleys.
Also: 1990 to 1994 Porsche C2 and C4 and all Porsche 993s use a (M10) 10mm 12 point socket tool to hold the alternator shaft when replacing the belts the area between the alternator and car body is very limited a 10mm 12 point spanner style wrench works well for this job.
Double End Wrench Set 19.99
Double End Wrench Set
Mirror polished, chrome vanadium steel. All purpose tools do the work of socket wrenches, box end wrenches and/or nut drivers. Sizes included 10 x 11mm, 12 x 13mm, 14 x 15mm, and 16 x 17mm.
Quality Brake Caliper Brush 22.50
Original Mercedes Factory Tool Brake Caliper Brush Heavy duty steel wire. Angled head for access. Very nice cusion comfortable handle and grip. Factory tool number 000 589 2668 00
New Style Mercedes Oil Wrench 24.50
New Style Mercedes Oil Wrench 74mm with 14 Points (inside flats flutes).
Mercedes M102, M103 etc..
Check your manuals for details and size needed.(Measure filter diameter or canister diameter.
See ref number mb 103 589 0209 00
This is an excellent deal. Other applications include: Audi, VW Golf, and new body Jetta, TDI (Diesel) and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle.
Live Data Hand Held Scanner 2890.00
Tired of high prices on Scanners? Serious Inquiries email sales@zdmak.com or call Toll Free 877 938 6657. X431 Master is the latest model of Launch X 431 series diagnostic tool. Launch products old world wide for a decade, the X 431 series has a reputation for its wide range of vehicles and full functions of its software. Based on the X 431, the Master gets a new structure and better design; also the hardware is upgraded. X431 Master will be released to the world wide market on 1st September, 2009. Inheriting from x 431 series, the X431 Master gets the open operating system: the highest level of automotive diagnostic technology in the world; function of read DTCs, read DataStream, actuation test, sensor waveform display and ECU coding as well as the PDA functions. It is easier and more convenient to operate than X 431 based on the smart design. The advantages of X431master compared to X 431:
1. Integrated design, combining the smartbox, miniprinter and main unit, a new designed and cover made from high quality materials to stand in a new market
2. Add the strap to the side face; easy to carry and ergonomical to use
3. The new smartbox add the The X431MASTER has a new connector to replace all CAN Bus and OBD Connector called OBDII 16E connector, which would be OK to test most of the vehicles.
4. Upgrade the hardware and communication modules, safer and faster communication with cars than X431 by intergraded design to save time in work
5. No more downloading of the diagnostic/communication software, start diagnosis program directly
6. 10.8V 40V operating voltage capability is added to work with different kind of batteries.
8mm Hex 1/2 Drive 13.99
Big Sturdy 1/2 Drive Hexagon 8mm (Allen) Socket 1/2" drive Overall length of the tool is 4 1/4 inches. Tool used for cylinder headbolts. Heavy Duty 8mm Allen.
M10 Tri Square (Old Style) 13.99
Headbolt Tool style XZN (Triple Square 12 Point) Socket. Sturdy 3/8 Drive Tool used for a wide variety of applications including headbolts.
Great for working on German vehicles. Mercedes and VW especially. This tool is 4 inches long and the shaft is 3 inches. Audi and VW people will often use this tool to remove old style (12 point Headbolts before installing new ones. Please note: this tool is not usually used for the new headbolts. Type in number T10070 for the newer tool. This sale is for one M10 (old style) socket only.
Mercedes 8mm Dogleg Allen 13.99
Sturdy 1/2 Drive Dog leg (offset) 8mm Allen Socket Applicable: M116, 117
1/2" drive
Overall length of the tool is 4 1/4 inches.
Tool used for R&R of cylinder head bolts.
Similar to Mercedes number 000 589 3407 00.
Dogleg and 8mm Hex Set 27.99
Hex Tools (2) Dogleg Plus Regular 8mm Allen
Set of Two Tools Sturdy 1/2 Drive Dogleg (offset) 8mm Allen Socket Applicable: M116, 117
Overall length of the tool is 4 1/4 inches.
Tool used for R&R of cylinder head bolts.
Similar to Mercedes number 000 589 3407 00.
Plus 8mm (straight) standard Hex 1/2 drive.
Excellent tools for working on Mercedes and other German vehicles.
German Car Lovers Special 79.95
Very cool combo package (set of 3) for the German car mechanic.
You will get one of each set..the Stubby hex and the Stubby triple squares
and the standard triple squares (better for headbolts)
9 Pc Metric Hex Stubbies 1/4 Drive Set (Lower right side of image) great for working on German Cars. Sizes included: 2mm, 2.5mm, 3, 4, 5, 6, 7, 8, 10mm. S2 Alloy steel THE STRONGEST DRIVERS AVAILABLE. Drivers heat treated to 56 to 62 RC. Satin Chrome plating.
Plus
8 Piece Stubby XZN Triple Square Set 3/8 Drive (Upper right side of image) Sizes included: 4mm, 5, 6, 8, 10, 12, 14 and 16mm Comes with the plastic carrying case. Sturdy compact One Piece design...SWEET. Satin Chrome with black impact tips. Super "New" S2 Alloy Steel. Fully Heat Treated
Plus
Standard XZN Triple Square Headbolt Bit Set of 4 (left side of image)
Includes sizes : 6mm, 8mm, 10mm & 12mm bits with 3/8" Drive holders comes on a rail.
A very handy set for the German car mechanic.
Dont miss out on this deal! You get all the tools in the image above!
Female E Torx Driver Set 63.50
Female Torx
Screwdriver Set 6 Pieces E4, E5, E6, E7, E8 & E10, orange vinyl handles.
Super High Quality Tools. Very rare and hard to find torx female drivers!
New! Master Ball Drive Set 55.00
Another ZDMAK Special!
New Master Ball Drive COMBO Set
Made of Super S2 Steel, the strongest and hardest bits available.
Master Ball Drive Bit Set Includes
Torx, T10 thru T55
Metric Hex, 2mm thru 10mm
and SAE/Inch Hex 3/32? thru 3/8?
Ball head to reach fasteners in difficult locations.
Includes magnetic bit holder and magnetic bit driver.
Metric Ball Hex Tool Set 14.95
Very Cool Metric Ball Hex Set 11 Pc
1.5mm thru 8mm ball hex bits, VI10 magnetic driver & 1/4" hex X 1/4" Sq.Dr. chrome bit holder in blue plastic box.
L Torx 6 Piece Set 10.99
L Torx 6 Piece Set Sizes included: T40, T45, T47, T50, T55, T60. Chrome vanadium steel construction.
Excellent for the professional or shadetree mechanic.
Spark Plug Wrench Set 12.99
STANDARD plus LONG PATTERN
Works on both 5/8 and 13/16 SPARK PLUG WRENCH
Tool for easy spark plug removal
Fits both 5/8" and 13/16" spark plugs
Includes handle for leverage.
Comes in both sizes 3 1/2 and 5 inch (overall length).
Cut & Pull Wire Strippers 14.99
Cut & Pull Wire Strippers cuts and removes insulation from wire with a single squeeze of the handle.
Accepts 18, 14, 12, 10 and 8 Ga AWG wire. Heavy duty tool with vinyl handle grips.
Long Torx Bit T30 Airbag Tool 7.50
Long Torx Bit T30
Airbag Tool Torx (6 Point) Size T30
Overall Length is 4 inches. Quality Tool for BMW, Mercedes and VW.
High grade tool steel bits,
hardened for ultimate wear resistance.
Flex Spark Plug Socket Set 11.99
Set of 2 Flexible Joint (Universal Joint) Spark Plug Sockets including one of each: 5/8 (16mm) Spark Plug Socket 3/8 Drive Flexible joint 6 Point Socket with Neoprene insert and 13/16 (20.8mm) Spark Plug Socket
Excellent for the professional or shadetree mechanic!
Suction Gun 14.99
54220 S Suction Gun

Perfect for transmissioins, differentials, gear cases, lower units, crankcases, etc.
No priming necessary
Die cast zinc head cap
12" flexible hose
1 pint capacity.
PRO WIRING KIT 12.50
80 pc PROFESSIONAL WIRING KIT
Call for availability.
Crimping tool with insulated handles .
Assorted connectors & terminals in storage case.
0 6 Inch Digital Caliper 29.99
6 inch Digital Stainless Steel Caliper with Case
Features & Benefits
0 6 inch Range (0 150mm)
Large easy to read LCD display
Comes in a plastic case to store when not in use.
Hardened stainless steel, Zeroing feature,Thumb wheel and lock.
Comes with an extra battery.
Torque Angle Guage 13.99
Torque Angle Guage 1/2 inch Drive
Measures angle of rotation after pre torque load in torque angle applications.
360 degree scale clearly marked in 2 degree increments and intervals of 10 & 30.
Easily zero the gauge by turning housing for next application. For the fasteners used on some vehicles, automotive manufacturers are specifying both torque and angle settings. With the gauge, the professional mechanic can meet the demands of the new specifications: to turn the fastener a specified number of degrees after initial torque is set. The gauge takes the guesswork out of tightening by indicating the number of degrees that the fastener is turned on a large, easy to read scale.
360 angle scale clearly marked in 2 increments, and in intervals of 10 & 30
Indicator etched on clear plastic plate protects angle scale from dirt and grease
Adjustable arm keeps angle scale stationary. Arm has two lengths for additional flexibility in placement against components.
Easy disassembly for cleaning just unclip retaining ring.
Torque + Angle Specification:
Example: If a torque + angle specification is given as 50 Nm + 70, the fastener is first torque to a threshold of 50Nm; then it is turned 70. If the specification reads 50Nm + 70, torque is first set to the 50Nm threshold. Each bolt in the sequence is then turned 70 once. When the entire sequence has been tightened to 70, each bolt in the sequence is given a second 70 turn.
The Torque + Angle Method:
Select a torque wrench, which indicates the threshold value at midrange. Torque the fastener to the manufacturers threshold torque.
Attach the proper size socket to the gauge. Attach the socket with gauge to the fastener.
Turn the arm clockwise until it meets a firm point of resistance.
Zero the gauge by turning the housing until it lines up with the 0 setting.
Connect a breaker bar, ratchet or other square drive to the gauge.
Holding the arm assembly firmly, turn the fastener the number of degrees specified. The proper clamp load has now been set and no further torquing is needed.
Torx Super Set 99.50
TORX LONG BLADE SET
TORX 18pc. Set, T10 thru T50 Torx Drivers T10 thru T50 Set includes both 4.5? (LONG) and 8? (EXTRA LONG) Torx Drivers All bits are S2 steel, the strongest hardest bits available Chrome Bit holders, with Black oxide blades Drivers have 1/4? or 3/8? square drive Press fit bits & holders Comes in a Plastic storage case.
Expanding Hood Prop 28.50
Telescoping Hood Prop 20 to 46 inch range. Red anodized Aluminum twist lock. The image shows both positions.
Push Pin Pliers Set of 2 39.95
PUSH PIN REMOVAL PLIERS SET Push pin pliers are designed to remove plastic push pins on Honda, Toyota, GM, Saturn and many other vehicles. Special ground tips remove the pins without damage. Pliers can also be used to remove U Joint circle clips. One tool with a 75 degree offset head to allow push pin removal in tight areas. These tools will save you time and headaches.
6 Piece Torx Driver Set 13.99
Torx 6 Piece Set (Torx = 6 Point) Drivers Oversized handles fo reasy use. Magnetic tips. Contains: T 10, T 15, T 20, T 25, T 27 & T 30
Metric 40 Pc. Tap and Die Set 26.99
40 pc Tap and Die set Metric sizes:
M3 x 0.5, M3 x 0.6, M4 x 0.7, M4 x 0.75, M5 x 0.8, M5 x 0.9, M6 x 0.75,
M6 x 1.0, M7 x 0.75, M7 x 1.0, M8 x 1.0, M8 x 1.25, M10 x 1.25, M10 x 1.5,
M12 x 1.5, M12 x 1.75 and 1/8 NPT
Super 4 Magnet Tray 24.50
4 Magnet Tray
Sticks to almost any metal surface
Keeps small metal parts and tools
from getting lost
Even works sideways or upside down.
4 Heavy duty rubber covered magnets.
Tray size 11 1/2 x 10 3/4
T Handle Hex Set 14.95
10 pc T HANDLE HEX KEY SET Heat treated alloy steel shafts. Plastic grips add comfort & turning power. Bonus storage tray mounts on wall or bench. Metric Sizes: 2, 2.5, 3, 4, 4.5, 5, 5.5, 6, 8 & 10mm.
Metric Feeler Guage 8.99
25 Straight Blade
Feeler Guage Set
Thickness In millimeters
The blades in this guage set are metric sizes. 0.04 thru 1.00mm
Excellent for the professional or shadetree mechanic.
Tie Rod Puller 24.00
Tie Rod Puller Jaw Opening size is 3/4 inch.
The opening from bolt to jaw = 1 15/16 Click Here to see a Drawing on this Tool &nbsp;
Super Hex Set 17.99
Super Set Metric and SAE Hex Sockets
1/2 Drive 6 Piece Set
Sizes: 12mm, 14mm, 17mm plus 3/8, 1/2, and 9/16 inch
Hex Sockets in popular sizes.
Sockets on a rail Hex (Allen) Sockets
Great for working on German Cars.
Super Deal
Stud Puller Set Metric 29.95
4 Piece Stud Remover Set Engine block studs usually need to be removed before machining. Roller cam design locks on stud to remove or install studs with minimal thread damage. Set works on 6mm, 8mm, 10mm and 12mm studs.
Remove right or left threaded studs without damaging threads. Turn with 1/2in. drive ratchet or 13/16in. wrench. Pass through design is perfect for extra long studs.
Pistol Style Blow Gun Kit 17.99
Pistol Style Blow Gun Kit Includes the most popular Blow Gun bodies and accessories Use for blowing out tubes and pipes; directing a fine stream of air; concentrating air; accessing restricted areas and filling tires. male x 1/4" NPT Female Inlets on inline Blow Includes Pencil Type Tire Gage, two sides 10 50 PSI in one pound increments and two sides 70 350 kPa in 10 kPa increments. 1/4" NPT Female Inlet on Pistol Grip Handle and 1/4" NPT Female x 1/4" NPT Female inlets on Inline Body. Chrome plated. Supplied in a durable, plastic molded storage case.
Stubby Set and Driver Bonus 49.99
Socket Set plus 1/4 inch Flexible Driver
Drive size on the sockets and the flex tool is 1/4 inch.
Flexible Drivers work well on many applications.
This is a very handy tool especially used in conjunction with these stubby sockets.
Rubber coated flexible shaft.
Metric Hex Stubbies 1/4 Drive
9 Piece Set
Stubby Hex Metric Sockets in small popular sizes. These are the Sturdy One Piece Design. Quantity 9 Sockets Hex (Allen) Sockets great for working on German Cars.
Sizes included: 2mm, 2.5mm, 3, 4, 5, 6, 7, 8, 10mm. S2 Alloy steel THE STRONGEST DRIVERS AVAILABLE.
Drivers heat treated to 56 to 62 RC. Satin Chrome plating. Sockets come in the plastic case.
Super Tools from ZDMAK!
5 Point Star Socket Set 14.99
9 PIECE SECURITY TORX PLUS SOCKET SET
5 Point Star Security TORX PLUS Sockets
Set includes sizes TS10, 15, 20, 25, 27, 30, 40, 45 and 50
These are Security Torx Plus Tools and they Do NOT work in a standard Torx Fasteners.
These are called 5 Point Star (some German tool books call this style IPR) Reminder: These are TAMPERPROOF (hole in the tip) 5 point tools very rare and hard to find set of sockets.

Torx, Torx Plus and Camcar are registered trademarks of Textron, Inc. Torx plus is designed to allow greater torque, and to minimize wear.
Two (2) Tools For Mercedes 84.00
SET 2 Repair Tools For Mercedes. This is the correct pin socket required to remove the input flange from the differential on all w110, w111, w108, and w109 chassis Mercedes cars built during 1961 to 1972 with swing axle style rear differential/axle assemblies. More Details:
Diagram on Tool 1a If you have a leak at the differential input flange oil seal, this tool removes the special nut located down inside the flange. Once this nut has been removed, the flange pulls off, exposing the input seal.
When reinstalling the nut using this tool pay close attention not to over tighten the nut so that the differential pinion bearings are not damaged.
There is a similar nut and flange at the rear of the transmission, however, it requires socket number TOOL 1b. (see images)
Diagram on Tool 1b

Buy these as a pair, and be well prepared to change out your leaking 40 year old transmission output and differential input seals."
You get both tools with this purchase..
MB Bulb Holding Tool 11.50
Holding Tool Pin socket Original Factory Tool (plastic) for removing and installing socket bulbs in the instrument cluster without having to remove the complete instrument cluster. Models 129, 140, 163, 170, 202, 203, 208, 209, 210, 211, 215, 220, 230, 240, 414.
MB REF 129 589 0109 00.
2 Piece Set 29.99
Set 2 tools for Mercedes repair.
1.Locking Hook needed for securing the visco fan coupling during R&R of 8mm hex fastener w/o removing the radiator. Applicable: Mercedes engine M103.

2.Long Pattern Thin Wrench 32mm.
Antenna Wrench & Radio Service Set 29.50
Antenna Wrench & Radio Service Set Removes most foreign and domestic radio antennas Includes tools needed to install and remove radios in GM, Ford and Chrysler vehicles Bonus Universal Code Retrieval Tool Kit includes: 8 Opening Universal Antenna Wrench Ford Radio Removal Tool GM Standard & Tamper proof Radio Removal Tool
3 Driver Sets with Pouch 65.00
3 sets of "Mini" Drivers:
Mini Torx Set, Mini Hex Drivers and Mini Screwdrivers...All in one pouch.
At a super Price!
Check into it.
Or buy each set separately.
Mini Screwdriver Set 27.50
Miniature Screwdriver Set:
P00, P0, & P1 Philips, 1.0, 1.6, 2.0 & 2.4mm wide flat tip.
Lube Wrench Set 46.50
6 Pc. Rubber Grip Oil Drain Wrench Set
Includes: 9/16", 5/8", 3/4", 14mm, 15mm, and 16mm combination wrenches.
? 6 point box end will not strip drain plugs.
? Anti slip TPR rubber grips.
? Lifetime Warranty, against breakage of body.
Impact Quality S2 Bit Set 10.50
Impact Quality S2 Bit Set, 8pc Bits 5/16" Hex bodies, 1.25"L, P1 P4 Phillips & 1/4", 5/16", 3/8", 1/2" Flat Bits, Plastic Holder
Big Daddy Master Hex Set 89.99
This is a big Master Hex Socket Set Metric and SAE
Get yours now. Comes with all the popular METRIC sizes for working on European vehicles plus all the SAE bonus sockets!
Metric sizes are: 19, 17, 14, 12, 10, 9, 8, 7, 6, 5, 4, 3, 2.5.
SAE 3/4, 5/8, 9/16, 1/2, 7/16, 3/8, 5/16, 1/4, 7/32, 3/16, 5/32, 9/64, 1/8 inch.
Metric Hex Drivers 2mm thru 19mm SAE, Fractional Drivers 3/32? thru 3/4? All bits are S2 steel, the best bits available Chrome Bit holders, with diamond knurl for fingertip control Drivers have 1/4?, 3/8? or 1/2? square drives Plastic storage case Press fit bits & holders.
Lifetime Warranty
On Sale 22mm Crowsfoot Socket 13.50
ON SALE
22mm OXYGEN SENSOR SOCKET This is a Special 6 Point 22mm Crowsfoot Socket with 3/8 Drive Used for the removal and replacement of Oxygen Sensor that are situated within a confined area.
No need to snip the wires leading to the unit when all you want to do is check the sensor. Applicable: Many European Models.
Spark Plug Wire Plier Bonus Set 47.99
SET OF 4 TOOLS
Spark Plug Wire Pliers
Used to remove the newer high voltage type wires
Wide grip section and special angle. makes it
easy to remove wires without separating crimps.
Applicable: 102, 103, 104, 110, 115, 116, 117, 119, 120
Same as Mercedes Tool Number 104 589 0037 00
also same as Zdmak item M104 0037X
PLUS SET OF 3 SOCKET TOOLS
Set of 3 Spark Plug Tools Including : Extra Long 5/8 (16mm) Spark Plug Socket Overall Length is 4 1/2 inches. 3/8 Drive size. Knurled drive end plus rubber insert for better grip. Plus one of each Flexible 5/8 and 13/16 Spark Plug Sockets 3/8 Drive Flexible joint 6 Point Sockets with Neoprene insert. Excellent for the professional or shadetree mechanic.
Starter Wrench Set 5 Pc 29.99
Metric Obstruction Wrench Set 5 Piece
Size 8 x 10mm
11 x 13mm
14 x 15mm
17 x 19mm
21 x 22mm
12 Point Tools used in a wide variety of automotive repair applications. Specially designed for starter bolts and used mainly for starter motors and inlet and exhaust manifolds.
Valve Plier 18.95
Valve Stem Seal Plier 10 218A Tool is used for the proper extraction of stem seals. The inside grooves on the tips of this Plier allows the firm grip of both O.E. and aftermarket seals. Applicable: Most Overhead Cam engines.
Orbit Pivoting Driver Set 2 27.50
Set of 2 Drivers SoftFinish Orbit Pivoting Phillips: Set includes Driver Size 1 and 2
With the new development SoftFinish Orbit, Wiha has again succeeded to set the standard in the tool industry. The speciality of this tool is the spring mounted pivoting tip, which centers itself independently when being inserted into the screw head. The result is a screwdriver, which is strength saving, particularly comfortable and allows quick work for angles of up to 20. The carefully hardened and burnished screwdriver tip, which is manufactured from a special steel alloy is integrated into the blade. The proven SoftFinish multi component handle provides for fatigue free work, and a safe and slip proof grip. No matter the application, with the SoftFinish Orbit you are properly equipped to efficiently tighten or loosen Phillips or Pozidriv screws. This tool offers amazing comfort, with highest functionality in the well known and proven quality. Made in Germany. Works on all standard phillips head screws.
Super 3mm Hex 11.50
Super Long T Handle with 3mm Hex Allen. Overall Length 15 inches. Blades of Special CRM 72 Tool Steel. Through Hardened, Anti corrosion Nickel Finish Ergonomic Comfort Grip T Handle Shaped for Maximum Power & Comfort Handle Molded over L Key for permanent bond. Guaranteed Quality Made In Germany!
Magnetizer/Demagnetizer 7.95
Compact Magnetizer/Demagnetizer Instantly Magnetize or Demagnetize Steel Tools & Small Parts (Works with items over 1.3" in length and 1/8" or 3mm diameter). Uses two C5 Permanent Industrial Magnets. No batteries or electrical required. Pocket sized 2" x 2" x 1"
7 Pc. Thin Pattern Open End Set 62.50
Made in Germany 7 Pc. Thin Metric Open End Wrench Set picture is for reference only
These are "HEYCO" brand wrenches SERIOUS HIGH QUALITY TOOLS Chrome Plated Polished Heads Narrow Profile for Easier Access In tight Locations Satin Chromed Sure Grip Body Made from 31CRV3 High Performance Tool Steel Precision Formed For an Exact Fit OEM Specified By BMW, Mercedes & Rolls Royce Guaranteed Quality
Made In Germany Sizes Included : 6 x 7mm, 8 x 9mm, 10 x 11mm, 12 x 13mm, 14 x 15mm, 16 x 17mm, 18 x 19
Meets DIN 3110 / ISO10102 Specifications.
Mini Folding Ruler 11.50
Pocket Sized Flexible Folding Water Proof
Pocket Ruler for Tool Box or Tackle Box!
Impact Resistant Tough Yet Flexible
Chemical, Water & Scratch Resistant
Play free Precision Joints with 90 degree stops
Permanent Deep embossed scale on both sides
Maintenance Free, Will not Rust or Kink
39"inch /1Meter O.A.L.
Folded Size 5" L, 1/2" W, 3/4" D
1/16" & 1mm/CM Marks
Long Life MaxiFlex Folding Rulers
Made From Fiberglass Reinforced Polyamide
Comes in plastic Storage Pouch
Swiss Made Quality!
Angle Tip Relay Plier 9.99
Angle Tip Relay Plier designed to remove and install relays which are usually located in hard to reach or confined areas. Specially coated tips offer a solid grip on the relay.
12 Pc. Terminal Tool Set 39.95
12 Piece Terminal Tools wire terminal extractor kit
Tools used to release DC wiring terminals from the harness that connect to ECUs, sensors, etc., found on most late model vehicles Special Electrical/Terminal Tools designed to remove wires from terminals without damage. Comes in the handy plastic case
Set 3 Alternator Tools 37.50
Set of 3 Tools consisting of: 19mm Multi Spline (short socket), plus XZN 12 point socket tool size M10, plus T50 TORX tool 6 point.
YOU GET ALL THREE TOOLS WITH THIS PURCHASE.
THIS 3 PIECE SET IS ESPECIALLY FOR THE MERCEDES PEOPLE WHO NEED THE T50 SHOWN AT THE BOTTOM OF THE IMAGE.
Three tools for mounting and dismounting the alternator pulley. Volkswagen Audi Mercedes Porsche etc...mounting the V belt pulley (slip clutch pulley) at the alternator (some older manuals call it a generator), especially for T.D.I. VW Golf III, Vento, Passat and AUDI A 3. The short serrated socket (3400) is size 19mm outside diameter and Length is 30mm. The longer tool at the top of the image is M10 XZN triple square and is 3/8 drive x 4 inch length. Porsche people see repair Group 27 (Porsche Bulletins) Boxster Alternators with free wheeling Pulleys. Also: 1990 to 1994 Porsche C2 and C4 and all Porsche 993s use a (M10) 10mm 12 point socket tool to hold the alternator shaft when replacing the belts the area between the alternator and car body is very limited.
Set 2 Alternator Tools 23.50
Combination Socket Set of 2 consisting of the Multi Spline (short socket) and the long XZN (12 point socket) size M10 for mounting and dismounting the alternator pulley. Volkswagen Audi Mercedes Porsche etc...
For mounting the V belt pulley (slip clutch pulley) at the alternator (some older manuals call it a generator), especially for T.D.I. VW Golf III, Vento, Passat and AUDI A 3.
The short serrated socket (3400) is size 19mm outside diameter and Length is 30mm.
The larger tool is M10 XZN triple square and is 3/8 drive x 4 inch length. See repair Group 27 (Porsche Bulletins) Boxster Alternators with free wheeling Pulleys.
Also: 1990 to 1994 Porsche C2 and C4 and all Porsche 993s use a (M10) 10mm 12 point socket tool to hold the alternator shaft when replacing the belts the area between the alternator and car body is very limited a 10mm 12 point spanner style wrench works well for this job.
Mercedes Benz ref no: 601 589 00 10 00 & 602 589 00 10 00
2 Alternator Tools with TORX 23.50
Socket Set 2 Tools consisting of the 19mm Multi Spline short socket and Torx T50 (longer 6 point socket).
Some manuals describe this application as "mounting and dismounting" the alternator pulley or V belt (slip clutch pulley) at the alternator (older manuals call it a generator) especially for Mercedes, T.D.I. VW Golf III Vento Passat and AUDI A3. (Please note the Volkswagen application requires an xzn style size m10 in place of the T50 some Mercedes require T50 and that is the reason we put this set together.
The short serrated socket MULTI SPLINE 19mm tool (many tool books call this size 17mm but a more accurate size would be 19mm) outside diameter and length is 30mm.
The larger tool is a torx T50 and and is 3/8 drive and 4 inch overall length used to hold the alternator shaft when replacing the belts the area between the alternator and car body is very limited a T50 style socket works well for this job.
You will get both tools with this purchase. The short MULTI SPLINE TOOL is extremely popular and covers a wide range of vehicles INCLUDING Mercedes and Volkswagen Audi Porsche.
Half Cut Torx Set HOT! 29.95
THEY GRAB BETTER!
RARE AND UNIQUE Half/Cut Torx 10 Piece Set. Torx Length cut to 1/2 the normal depth.
Increase Strength and Improve Fastener Engagement
1/4" Square Drive, with 3/4 inch Overall Length
Half/Cut TORX Drivers (will also Drive TORX Plus)
SIZES: T10, T15, T20, T25, T27, T30, T40, T45, T47 & T50.
S2 Steel, The Strongest Hardest Drivers Available
Heat Treated to 58 62 RC Knurled Body for Fingertip Control Satin Chrome Plated Drivers.
Set includes 10 pieces packaged in a durable plastic storage case.
2 Pc Plastic Auto Chisel 24.75
2 Pc Plastic Auto Chisel
Circuit Tester Tool 11.99
6 24 Volt Electric Circuit Tester Tool. Sharp probe tip covered with brass protection cap, check function of car lights faster and easier. Checks range: 6 12, 24v
Unique Compression Tester 29.99
Easy reading 2 1/2 inch diameter gauge features color coded quadruple calibrations with 0 300 psi, 21 kg/cm, 21 bar & 2100 kpa.
13 inch durable rubber hose with 14mm / 18mm adapter.
6 inch heavy duty stem with universal rubber cone adapter fits most plug holes.
Oil Drain Plug Key Set 29.99
12 Piece Oil Drain Plg Key Set Includes Hex style and square drive style sockets. Comes in the blow molded plastic carry case. Hex Sizes included are: 3/8, 8mm, 9mm, 10mm, 12mm, 14mm, 17mm, plus square drive sizes 5/16, 3/8, 11mm, 13mm
Auto Computer Memory Keeper 14.99
Auto Computer Memory Keeper
2 Piece Hook Set 12.50
2 Piece Hook Set Remove radiator hoses from clamp, pull cotter pins and other tough jobs.
U Joint Spark Plug Sockets 13.99
Excellent Set of 2 Magnetic Sparkplug Sockets 3/8 drive With Flexible U Joint You get two tools with this purchase
Sizes: 16mm (5/8)
and 21mm (13/16)
The universal joint allows for a smooth, bind free action while increasing access.
Set 5 Point and 6 Point 59.95
Super Set including 5 Point and 6 Point Tools. You get full coverage with this Extra Long Security Torx Driver Set
Features 12" long blades with TamperProof Torx on one end and 5 Point security tips on the opposite end.
Double drive screwdriver handle, bits can be inserted as a standard screwdriver, or as a T handle.
S2 steel, the strongest hardest drivers available! Heat treated to 60 62 RC
The blades are satin chrome plated with a black tip on the 5 point end.
New extra long security driver set, includes 12" long interchangeable blades with T10 thru T40 Tamper Proof Torx on one end and 5 Point security Drivers on the opposite end. The Blades can be put in the 2 Way screwdriver handle as a screwdriver or use the "T" handle. The set also includes a special bit holder so these blades can be used with your favorite 1/4 drive ratchet handle. Comes with a plastic storage case.
Tamperproof Torx Set 19.50
Extra Long Arm Torx L Key Set Tamper Resistant (tamperproof) Drilled tips allow use on tamper resistant security fasteners Chrome molybdenum steel construction for strength and durability Mirror polished chrome plated finish resists corrosion Patent pending textured finish for improved grip Color coding for easy identification and Laser etched size markings are easy to read This Extra Long Arm Torx Key Set contains the following sizes: T10, T15, T20, T25, T27, T30, T40, T45 and T50.
Security Bit Set 13.99
32 PIECE 3" SECURITY BIT SET
Bits fit most power drills, screw guns and magnetic drivers. Set contains many common tamper proof sizes including tri wing bits, torX bits, spanner bits and hex bits.
Ratcheting Female Torx Set 52.00
Check out this Torx Set.
Female Torx Hard to find.
This set features a standard driver handle
anda ratcheting handle bonus!
Details: 7" Long Blades 10 Pc includes: Inverted Torx nut drivers E4 thru E16, ratcheting "T" handle, and 2 way screwdriver handle. Packed in storage case
(picture is for reference the image shows the complete set above and it shows both the handles in action).
The torx sizes in this set are: E4, E6, E7, E8, E10,
E12, E14 and E16.
11 Piece Set Interior Tools 43.50
11 Piece Set Interior Tools. Specifically designed set including tools with extra slim profiles for the finer jobs. Special contours and unique features for effective and safe removal of fine or delicate bezels and fascia. The Pry Tools will not scratch or mar fascia. It tackles finer jobs that the average tools are too big for. These tools are made from impact resistant high quality nylon. Each Pry Tool within this six piece Fine Kit (on the right side of the image is specially designed with an extra slim profile and unique shape for the delicate task of removing small or fine fascia trim and bezels of; dashboards, air vents, door panels, door locks, electronic seat controls, seat levers, center counsels, gear shifter, etc....Super Tools for Auto Interior Work! This 11 Piece Set of plastic pry pullers is perfect for working on those expensive panels on car interiors. It will also help work loosen plastic decorative inserts, door moldings and countless other pieces on todays modern and many vintage cars. This set has more features plus quality of this set is great. (stronger and more durable) than other being sold, making this a much better deal...THERE IS A HIGH DEMAND for these interior tools.
Metric Hex Stubbies Set 35.99
Impact Quality STUBBY (short pattern) HEX Set 3/8 Drive. Picture is for reference only. This is an 8 piece set. Sizes 6mm thru 19mm. Overall Length of each tool is 28mm. Super new S2 alloy steel. THE STRONGEST DRIVERS AVAILABLE. Drivers heat treated to 56 to 62RC. Gun metal blue plating. This set is the same as our number M600.
You will get all 8 pieces with this set.
16 Piece Hex Set 69.99
16 Piece (short pattern) Impact Quality Hex Set 3/8 Drive.
Overall Length of each tool is 28mm. Super new S2 alloy steel.
THE STRONGEST DRIVERS AVAILABLE!
Drivers heat treated to 56 to 62RC. Gun metal blue plating.
SAE Sizes: 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8" and 3/4".
Metric Sizes 6mm, 7mm, 8mm, 10mm, 12mm, 14mm, 17mm and 19mm
You will get all 16 pieces with this set.
Valve Stem Seal Plier and Kit 59.99
Valve Stem Seal Remover/Installer Kit
Works on both valves still seated or removed. Precision machined seal driving adapters guide the seal for proper setting. Set contains: Valve stem seal plier. Drive handle 6? (150mm) long.
2 Deep seal driving sockets for seals O.D. 10.8 14.8mm
7 Seal driving adapters fit seals 5mm, 5.5mm, 6mm, 6.6mm, 7mm, 8mm, & 3/8?. Comes in the blow molded plastic carrying case.
Universal Joint Torx Set 19.99
5 PC. UNIVERSAL TORX STAR SOCKET SET CONTENTS INCLUDE SIZES: E8, E10, E12, E14 and E16 MANUFACTURED FORM MATT FINISHED CHROME VANADIUM. OVERALL LENGTH 60MM VERY RARE AND HARD TO FIND. TOOLS ARE 3/8 DRIVE. EXCELLENT SET FOR THE PROFESSIONAL OR SHADETREE TECHNICIAN ESPECIALLY FOR THE PRICE. THE TOOL BOOKS CALL THIS FEMALE STYLE "E" TORX (FOR EXTERNAL SCREWS AND FASTENERS).
T30 Half Cut Torx HOT! 6.99
THEY GRAB BETTER!
RARE AND UNIQUE Half/Cut Torx
SIZE T30
Torx Length cut to 1/2 the normal depth.
Increase Strength and Improve Fastener Engagement
1/4" Square Drive, with 3/4 inch Overall Length! WOW
Half/Cut TORX Drivers (will also Drive TORX Plus)

Please Note: Other sizes available :T10, T15, T20, T25, T27, T40, T45, T47 & T50.
TYPE IN THE SEARCH NUMBER HCT105C IF YOU WOULD LIKE TO SEE THE SET S2 Steel The Strongest Hardest Drivers Available!
Heat Treated to 58 62 RC Knurled Body for Fingertip Control Satin Chrome Plated Drivers.
Master Torx Set 35 pc 49.50
35 Piece Torx Master Set
1/4, 3/8 and 1/2 inch Drive Sockets in a blow molded case. Male and Female (Internal and External (E) Torx
Chrome vanadium, 2 piece steel construction.
Contains the following:
1/4" drive TORX Sockets
T 8
T 10
T 15
T 20
T 25
T 27
T 30

3/8" drive TORX
T 40
T 50
T 45
T 55

1/2" drive
T 60

1/4" drive Tamperproof TORX
T 7
T 8
T 9
T 10
T 15
T 20
T 25
T 27
T 30

3/8" drive Tamperproof TORX
T 40
T 45
T 50
T 55

1/4" drive Star TORX FEMALE
E 4
E 5
E 6
E 7
E 8

3/8" drive Star TORX FEMALE
E 10
E 12
E 14
E 16

1/2" drive Star TORX
E 18
Metric and Sae Half Moon Set 48.50
METRIC and SAE 10 pc. Half Moon Wrench Set. Some people call thse tools Obstruction or "Starter" Wrenches. This is a 10 Piece set (the box ends are 12 Points). Tools used in a wide variety of automotive repair applications. Specially designed for starter bolts and used mainly for starter motors and inlet and exhaust manifolds. Especially for use in confined areas. Sizes Included:

METRIC
8x10mm
11x13mm
14x15mm
17x19mm
21x22mm

SAE
7/8 x 13/16
3/4 x 11/16
5/8 x 9/16
1/2 x 7/16
3/8 x 5/16
Set 7 Spark Plug Tools 38.50
Set of 7 Spark Plug Tools
Including: Extra Long 5/8 (16mm) Spark Plug Socket Overall Length is 4 1/2 inches.
3/8 Drive size. Rubber insert for better grip.
Plus one of each: Flexible 5/8 and 13/16 Spark Plug Sockets
3/8 Drive Flexible Joint (6 Point) Sockets with Neoprene insert.

Plus Spark Plug Wire Tester
Identifies damaged spark plug wires easily.
Tester flashes in sync with spark plug firing
until it runs across a break in wire.

Plus Set Long and Short T Handle Tools
Works on both 5/8 and 13/16 Spark Plugs
Tools for easy spark plug removal
Includes handle for leverage.
You get one of each 3 1/2 inch and 5 inch (overall length).

Plus Spark Plug Gapper
Sets gaps quickly and easily.
Range .020 to .100 (.5 to 2.5mm)
Tapered hole to adjust gap.

You will get all seven (7) tools with this purchase.
Will make a nice addition to the tool set
or a great gift for the car fanatic!
Bulb Holding Plier 17.50
BULB HOLDING PLIER FOR REMOVING AND INSTALLING HARD TO REACH AUTOMOTIVE BULBS AND FUSES. WILL SERVICE SMALL INSTRUMENT CLUSTER BULBS, PLUS XENON, HALOGEN AND FILAMENT BULBS. BETTER THAN USING SCREWDRIVERS OR FINGERS. FEATURES MOLDED PLASTIC BODY WITH CUSHIONED INSERTS EMBEDDED IN TIPS TO PROTECT BULBS.
W163 ML Ball Joint Socket 19.99
Special Socket for Mercedes. Sturdy 3/4 drive tool to remove and install the retaining ring that secures the lower ball joint on Mercedes ML (W163) front and rear axle. Application: W163 M Class ML Series Models W163 (1998 2005) and W164 (2006 present), ML320, ML350, ML430, ML500, ML320 Diesel, ML550.
Mercedes Injection Socket 98.50
Special 22mm Mercedes Injection Socket Made in Germany by Hazet. 6 Point socket for injection nozzles on MERCEDES BENZ diesel engines. MB Types 202 (C class) and 210 (E class) with 604, 605 and 606 engines. 1/2 inch drive. Chrome vanadium steel. Original factory tool.
Trans Clutch Spring Compressor 59.95
Transmission Clutch Spring Compressor. For removing and installing the trans rear clutch piston snap ring adjustable for many domestic cars and light trucks. Applies pressure to the retaining washer in the clutch drum to compress clutch piston return springs in order to remove or install snap ring during repairs or overhaul.
Switch Blade Radio Keys 29.95
O.E. ANTI THEFT RADIO KEY SWITCH BLADE
Special features: (FULL COVERAGE FOR VW AUDI)
Each key folds into the body handle like a pocket knife.
Each half of the tool kit allows for an even pulling action.
SEE MORE IMAGES BELOW
The two halves slide and are held together via an interlocking channel.
Every Key in the kit is current up to 2005.
The full application range of this new kit is as follows:

Updated application key kit for Mercedes & all Porsche 996 and Boxster equipped with Becker radios.
Updated key combo for all Audi & VW radios up to 2004: models equipped with four horizontal (Audi) or two vertical slots (New Beetle, Jetta, etc.).
VW only key kit for Passat, Jetta, Golf models. This key application range ends where key kit 2 begins.
Five sided "pentagon" driver for most every BMW model, excluding E38 & E39 models.
Special Allen key for BMW E38 and E 39 models.
Standard "barbed hooks" (like U Hooks) for Ford, Chevy, Saab, Land Rover, etc.
Wood Handle (TANG Thru) Screwdriver Set 36.99
Wood Handle (TANG Thru) Screwdriver Set High Quality Tools (set of 4) Made in Japan. Set Includes: FLAT 5.5 x 75 and FLAT 6 x 100, Phillips 1 x 75 and Phillips 2 x 100 Round handles for more gripping power with Tang Thru design:
One piece shank and handle cap prevents damage to the
screwdriver when striking with a hammer. More details below.

The Flat 5.5 x 75 has a shaft length of 75mm and the overall length of this tool is 156mm
The handle is 32mm thick
The tip is 5.5mm wide and 0.8mm thick.
The shaft diameter is 5.8mm thick

The Flat 6 x 100 has a shaft length of 100mm and the overall length of this tool is 200mm
The handle is 41mm thick
The tip is 6.0mm wide and 0.9mm thick.
The shaft diameter is 6.4mm thick

The Phillips P1x75 has a shaft length of 75mm and the overall length of this tool is 156mm
The handle is 32mm thick
The tip is + No. 1
The shaft diameter is 5.8mm thick

The Phillips P2 x 100 has a shaft length of 100mm and the overall length of this tool is 200mm
The handle is 41mm thick
The tip is + No. 2
The shaft diameter is 6.4mm thick
Flywheel Lock Mercedes 34.50
BENZ FLYWHEEL LOCKING TOOL
USED TO FIX THE FRYHWEEL GEAR TO REMOVE & INSTALL CRANKSHAFT PULLEY CENTRE BOLT. APPL: MERCEDES M102, M103, M104, M111, M601, M602, M603, M605, M606, M611, M612, M613.
Set 3 XZN Tools 37.50
Set 3 Triple Square XZN Tools
Including sizes M18, M16 and M14
The 14mm 12 point socket with tamper proof hole Services 2003 and up VW Touareg and Porsche Cayenne Front Axle Bolts, various Audi/VW Axle Bolts plus Audi TT Differential Mount Bolts and Transmission Drain Plug.

The size 16mm Drain Plug Socket is a Special Tamperproof Transmission Drain Plug tool. Triple Square 12 Point for VW and Audi with ZF Transmissions Same as Volkswagen Tool 3357. For Porsche Boxster and Audi A4, A6 and Passat

The 18mm socket services Oil Drain Plugs and Engine Head Bolts on 2006 & up VW Bora and Touareg. Rare and hard to find sizes in this set!
Use with 1/2" square drive tools.

You get all three tools with this purchase.
Master Dash Ignition and Radio Tools 36.50
BONUS SET TOOLS FOR MERCEDES
This set includes radio tools for both new and older Mercedes. You will have virtually full coverage on radios from new and old Mercedes.

NO ONE ELSE SELLS A SET LIKE THIS

You get:
Ignition V shape Lock release Wires Ignition Lock Removal wires for W124, 126, 201
(similar to MB Number 900 589 0059 00)

PLUS
Long Hooks (Pair) for W107, 116, 123, 124, 126, 140, 201
Similar to Mercedes 140 589 0223 00
(Please note the original Mercedes hooks are 7 inches in length
the ones in this set are only 6.5 inches)

PLUS
Ignition Turning Tool (BLUE)
For loosening and tightening the ring (rosette) of the electronic ignition switch.
Applicable: W129, 140, 202 (as of June 1, 1997), 208, 210, 211, 230, 240, 463
The Aluminum will not leave marks on the interior parts.Benz ref: 210 589 0007 00

PLUS
Radio Removal Keys 1997 and older W129, 140, 202, 210

PLUS >>>BONUS KEYS FOR NEWER MERCEDES
You will have virtually full coverage with this bonus set (2) keys plus the keys that come in the case with the Hooks.
Very easy Tools / Keys to use, just slide into the Radio or A/C Instrument clusters slots and pull to remove in seconds. This is the only Tool that can be used to remove without damaging your Radio or A/C Climate control and instrument clusters on Mercedes Benz Cars A, C, E, SL, ML, SLK, CLK, S, M.Details: Special tools to remove Mercedes Benz car radios with out damage.

Fits the following radios:
Mercedes/Becker car radio e.g. Classic, Special, Exquisit all Audio models inclusive Audio 10
CD, CC, Command 2.0, 2.5, Sound 10, Audio 30 APS, APS2, APS3, APS4 a.s.o. This will work for the Radio and A/C + some Instrument clusters and most of new Mercedes Models
W123 200 300 (E Class) 1975 1986 200, 220 D, 230 E and CE, 240 TD, 250 T, 280 E and
CE, 300 D, 300 TD (Turbo Diesel) limousine, estate car (station wagon) T Modell, coup
W124 200 500 (E Class) 1984 1995 limousine, estate car (station wagon) T Modell,
coup, convertible, open topped car
W140 300 600 (S Class)
W163 230 500 (M Class)
W168 140 210 (A Class) 1997 2004
W170 200 320 (SLK) 1996 2004
W202 180 320 (C Class) 1994 2000
W208 200 320 (CLK Class)
W210 200 500 (E Class) 1995 2002 E 200, E 200, E 230, E 240, E 280, E 320, E 420, E
430,E 50 AMG, E 55 AMG, E 220 Diesel, E 300 Diesel, E 300 Turbodiesel, E 290 Turbodiesel, E 200 CDI, E 220 CDI, E 270 CDI, E 320 CDI 1995 2002, limousine, estate car (station wagon)
T Modell, coup W414, R170, R129 a.s.o.

This is a very nice set of tools for the Mercedes Professional or Shadetree Technician.

Testimonial: If you work on Mercedes you need these! These hooks pull Instrument Clusters flawlessly. Radio Tools work great. Ignition Tumbler Pins are perfect fit. Great all around Cluster, Tumbler & Radio Tools for any Mercedes Benz Home or Shop. NC Technician/Shop Owner Robert Palmiter
LOOK SMALL SIZE TORX SET 11.99
LOOK SMALL SIZE TORX SET Precision Pocket Screwdriver 8 Piece Pen Style Torx Bit Set. Rare and hard to find sizes at this price Includes small sizes: T3, T4, T5, T6, T7, T8, T9 AND T10 MAGNETIC TIP HOLDS BITS SECURELY. Bits storage is in th handle. Great tool kit for electronics (mobile phones cell phones etc...) Anodized aluminum alloy handle knurled for a sure grip. Comes in a clamshell package (notice the torx style pattern on the upper right of the image).
Set 2 Hooks 19.99
Set Two Tools (2) Special design to pull the rubber ring which is connected with the exhaust tube. You get both tools with this purchase.
Metal Clad Bushing R&R Kit 99.95
Metal Clad Bushing R&R Kit
Please read carefully: Tool set for replacing the wheel carrier bushing at the rear wheel carrier assembly (where all the links attach), and it works as good as the factory tool.
Some people wind up taking off every single link and bending the dust sheild while trying to R&R this bushing (with a standard shop press).
This tool is worth its weight in gold.
Although this tool is an aftermarket tool for the MB tool 202 589 00 43 00, it worked excellent in the field, and its about 1/2 the cost of the OE MB tool.
It works on Mercedes Benz chassis: 124, 129, 140, 170, 171, 201, 202, 203, 208, 209, 210, 215, 220, 221, 230, spanning 1984 present models
(not every model however, mainly the ones listed above).

w124 (1986 1995 300E/E320, 300D, E300D, 400E, 500E,etc), R129 (1992 2002 SL Models), w140 (Sclass from 1991 1998), R170, R171 (All SLK models, thru current), w201 (all 190E/D models), w202 (C class 1993 2000) w203 (c class 2000 2006), w208 & w209 (all CLK models), w210 (E Class 1996 2001), w215 (CL Class Coupe 1999 2006), w220 and w221 (S Class 1996 2006, S class 2006 present), and R230 (the new SL roadster). It is used to replace MB Bushing 220 352 02 27, which are now 221 352 00 27.

SAME AS 202 589 00 43 00 Removal and Installation Wheel Carrier Support Joint
(REPLACES) 140 589 07 43 00 Removal and Installation Tool
(REPLACES) 201 589 05 43 00 Removal and Installation Tool

This set comes complete with all the proper components to efficiently get the job done right. This tool works both on the car or on the bench!
Spring Installer and Hook Set (2) 32.00
Set of two tools for Mercedes brake work.
First tool (on the left) is for proper R&R of pressure spring on parking brake shoe. SAME AS MERCEDES REF 112 589 0961 00 Applicable: All Models.
Plus you get T Handle Brake Tool for mounting and dismounting the spring of brake shoes on vehicles with rear disk brakes.
Parking brake spring installation tool set makes removing and replacing parking brake shoes easy. Using improper tools can damage and deform springs. Easily replace worn out hold down springs to keep new shoes stable preventing premature lining wear. Versatile hardened hook is perfect for installing brake shoe return springs where space is extremely limited. These are the proper tools for doing this important job correctly the first time.
You will get both (2) tools with this purchase. To see more Images Click Here!
Hazet 2769 3 Mercedes 89.00
Hazet Mercedes Retainer Wrench 2769 3 Hazet 2769 3 Same as Benz tool 615 589 0003 00
Hazet 2769 Set 2 129.00
Hazet Mercedes Valve Adjustment Wrench Set of 2 Made in Germany This two piece set includes: Item Numbers 2769 and 2769 1 The 2769 is same as Benz Tool 601 589 0001 00 The 2769 1 is same as Benz Tool 421 589 0001 00Be sure to CLICK HERE for more HAZET TOOLS
Strut Master 599.00
SIR Tools Strut Master Strut Spring Compressor
Portable for convenient use, "On or Off The Car".
Exclusive self contained compressor is designed with fully adjustable jaws
Portability With The Power of a Work Station Model
It has a wide coil spring and strut application range
Equipped with the first of its kind, exclusive safety latch mechanism
Combined the best of both worlds Portability with the power of a work station model.
This exclusive self contained compressor is designed with fully adjustable jaws.
It has a wide coil spring and strut application range. It is portable for convenient use,
On or Off The Car Sturdy structure, it is as solid as work station models. It is light in weight with all the power of a Heavy Weight.
Equipped with the first of its kind, exclusive safety latch mechanism.
Plus it is designed for use with an impact gun.
Specifications & Capacities:
Minimum coil size O.D. = 4.00" inches
Maximum coil size O.D. = 10.25" inches
Maximum coil thickness = 3/4" inches
Vertical stroke = 11.75" inches
Maximum bolt stress load = 10,842 lbs/ft
Maximum compressor stress load = 12.786 lbs/ft
Total weight = 25lbs
SUPER TERMINAL TOOL 37.50
Introducing the SUPER Terminal Tool The "Swiss Army Knife" of wire terminal extractors. This internationally patented design offers the technician a handy "all in one" extractor kit that folds up and slides together into its own unique and compact storage housing. This kit is equipped with (12) factory correct extractor press bits. These press bits release DC wiring terminals from its harness that connect to ECUs, sensors, etc., found on most late model vehicles.
3 Piece Oil Service Set 25.00
3 Piece Oil Service Set includes sizes 36mm, 32mm and 27mm 6 point sockets. (36 mm for M52, M60, M62, M70, M73 engines) Special 36mm Oil Filter Wrench Removes and installs filters on BMW Mini Cooper. The low profile socket fits 36mm fuel and oil filters. The low profile socket works in confined spaces. 3/8 in. drive Not for use with an impact wrench. BMW Mini Cooper, BMW M52 6 cylinder, BMW M60 8 cylinder, BMW M70 12 cylinder. Mercedes Benz diesel engines: OM604, OM605, OM606 (1995 W124 E300 diesel, 96 97 W210 E300 diesel, 1998 E300 turbodiesel). Same as Mercedes tool number: 606 589 01 09 00VW Volkswagen VR6 Also for Ford Truck 6.0L 03 04
Plus you get the 32mm and the 27mm.
27 mm for R&R of oil filter cartridge element. App.: M163 (Class A), C230 (Compressor)
32 mm for R&R of Oil filter cartridge element. Applicable: Opel Astra, Corsa, VW Passat, Audi.
Split Socket 9.99
Deep Split Socket size 7/8
Removes and Installs Oxygen Sensors on Many Domestic and some Imports. Special Socket with slotted cutout for clearance of wire harness. Provides proper depth to fit over the sensor. Use with 1/2 square drive or wrench end.
Provides adequate depth to fit over sensor. Heat treated alloy steel.
M8 and M10 Triple Square Set 2 22.50
Set of 2 Tools
Triple Square (12 Point) XZN Sockets M8 and M10
Sturdy 3/8 Drive Tools used for a wide variety of applications including headbolts.
Excellent for working on German vehicles.
Each tool is 4 1/2 inches overall and the shaft is 3 inches long. The German tool books refer to the 12 point style as XZN. This is a very popular style.
Puller 44.50
Pilot Bearing Puller P1088X 12 15mm Universal Pilot Bearing and Blind Hole bushing Puller. Important: Removing the center bolt of this puller will allow you to penetrate an I.D. as small as 12mm. Do not use on an I.D. larger than 15mm Applicable: Most European Vehicles. Excluding Suzuki and Geo
U Joint Torx Set (Tamperproof) 45.00
Check it out.....NEW SWIVEL (U JOINT) HALF CUT, TAMPERPROOF TORX SET
TT10 Thru TT40 with 1/4'' Sq. Drive
4" Magrail TL Base (bonus!)
Satin Chrome Finish, Stubby Half Cut Torx With Tamer Proof
Universal Joint, Swivel Body, In Clear Plastic Box
HALF CUT (they grab better)
TAMPER PROOF (hole in the tip)
S2 Steel, Fully Heat Treated (the strongest drivers available)
Sizes included
T10
T15
T20
T25
T27
T30
T40
22 PC. ALTERNATOR SERVICE TOOLS 88.95
22 PC. ALTERNATOR SERVICE KIT TOOLS / Set of tools to remove and install press on type beltdrive Bosch and Denso Alternator Pulleys. Applications include VW, Audi, Seat, Mercedes, Renault, BMW, Ford, Fiat, Honda, Toyota, Porsche, etc. Components include Torx , Triple Square and Hex socket bits in standard and short lengths, an assortment of splined and hex reaction nuts and adapters and a 1/2'' square drive bit adapter. Packed in blowmold case.
Ball Hex Tool Set 49.99
Xtra Long "Ball" Hex Tools Super Set includes sizes 3mm, 4, 5, 6, 7, 8 and 10mm
XZN Stubby (short pattern) Set 27.95
XZN Stubby Set (EXTREMELY short pattern)
XZN Metric Socket 6 Piece Set.
Most common earlier sizes are 6, 8, 10, and 12.
Please note: Each Tool is 20mm in Length
Satin Chrome with New S2 Alloy Steel. These are some of the strongest drivers you will find.
Comes on a rail.
1/4 Drive Size.
This is a brand new set by popular demand. Triple square, also known as a XZN socket, is a type of screw drive. They are commonly found on German vehicles such as BMW, Mercedes, and Volkswagen etc... These screws/fasteners are used in some high torque applications such as cylinder head bolts and drive train components. Triple square bolts are common to early Porsche and Volkswagen (CV) constant velocity joints. Increasingly, triple square screws are found on other European and Asian makes of cars. Other names for this type of triple square screws and drivers are "Double Hex", "Double Allen", and "Aircraft Screws". Despite this, "Double Hex" and "Double Allen" are misnomers. The recess in these bolts is actually (as the name suggests) made of three squares, not two hexagons. The corners are 90 degrees, not 120 degrees. They are not double hexes, and an Allen key will not fit them properly.
These are XZN Triple Square Sockets. XZN means Triple Square or 12 point. If your tool books call for XZN or Triple Square or 12 Point, these are probably the tools you need.
These are Short Pattern "Stubby" Sockets. Short pattern for using when you are in a tight spot. Sturdy compact solid one piece design.
Each tool is 20mm Long
1/4 " drive size.
Magnetic Screwdriver 7.99
Magnetic Screwdriver 1/4" Hex
Quick Release magnetic socket; red & black Ergonomic handle; 3.5" blade.
10 inch Spark Pluck Socket 24.99
Extra Long Ten Inch Spark Plug Socket 5/8
Extra long socket with thin wall combines for great accessibility. Ideal for use on Toyota hemi style plugs, plus marine, small engine and specialty motors.
Drive size is 3/8 (square dr).
Phillips & Flat Set 14.50
Phillips & Flat Tip Bit Set 11 Pc
5/32" thru 5/16" flat & P0 thru P3 bits, VI10 magnetic driver & 1/4" hex X 1/4" Sq.Dr. chrome bit holder in green plastic box.
8mm Tools for Mercedes Set 2 62.99
TWO TOOLS FOR MERCEDES
ON SALE THIS WEEK ONLY
U Body with 8mm Allen Socket 1/2" drive. Needed for the proper R&R of cylinder head bolts. Some applications include: Mercedes M116 M117 (Same as Mercedes 916 589 0013 00)

Plus Dogleg (offset) 8mm Allen Socket Sturdy 1/2 Drive Some applications include: M116, 117 Overall length of the tool is 4 1/4 inches. Heavy Duty 1/2 drive tool used for R&R of cylinder head bolts.

You get both tools with this purchase. Both tools are 8mm Hex.
9 Piece XZN Set 65.50
9 Piece XZN Triple Square 12 Point Socket Set
SUPER STRONG S2 ALLOY STEEL BITS.
SOME OF THE STRONGEST DRIVERS AVAILABLE!
4 inch (100mm) LONG DRIVE TOOLS CHECK OUT THE SIZES!
M4, M5, M6, M8, M10, M12, M14, M16, M18 CHROME HOLDERS, 1/4, 3/8 and 1/2
DRIVE. PLASTIC BLOW MOLDED CASE. HEAT TREATED RC 60/63.
GREAT FOR USE ON GERMAN, ASIAN AND SOME DOMESTIC VEHICLES. THE GERMAN TOOL BOOKS REFER TO THE 12 POINT (triple square) STYLE AS XZN To see more XZN Tools simply type in the word XZN into our search field above.
Quality Utility Knive 23.95
High quality utility knive designed to take the abuse that would destroy ordinary knives. Any Electrician, Telephone Technician, or person doing general cable prep work should have one. Perfect for cutting and stripping wire or cable, opening utility outlets in plywood and sheetrock, or any general cutting application. Each Knife comes with a locking sheath and a ceramic sharpening stone. Equipped with a special high grade steel blade, the VDK1 is the perfect item to add to your toolbox. This knife is ideal for electrical, service work, or for any general cutting application. High quality tool made in Japan.
Slide Hammer 29.00
Slide Hammer use with Tool M0046 for proper removal of prechamber from cylinder head. Also other applications: Tool pulls dented sheet metal back into place. To use, drill a hole in the deepest part of the dent, insert the hook or self threading screw tip and tap lightly with the 2 1/2 lb slide hammer to remove the dent. A 13 long shaft enables high pulling force. Slide hammer has 1/2 13 UNC thread.
Product Search

News

Events