test
This Page Type is Not Defined
ZDMAK SPECIAL TOOLS: PORSCHE TOOLS
 
911 Easy Rider Tool 89.00
Easy Rider * Height Adjustment Lever
This a "Brand New" special service tool P244 Developed to aid the technician with safe and easy ride height adjustment of rear torsion arms and/or general adjusting of Aftermarket Adjustable Spring Plates. The inherent design of this tool acts as an extension of the trailing arm by latching onto it at two hook points. The end of the protruding tool is supported by a roll around floor jack. You simply pre load the suspension and are able to maintain the travel in any desired position w/o having to use chains, which may slip, is very dangerous and generally non professional. Prior to this new Ride Height Adjusting Lever, a combo set up set up was used. Whereby, wrapping a chain onto the vehicle, sling it around the trailing arm, placing a jack between the chain and trailing arm. Thereby, rendering the jack to react against the chain/trailing arm. If the chain breaks or slips, BLAMO !
Professional Engine Holder Complete 349.00
Engine Holding Fixture Designed to securely carry the entire weight of a fully dressed air cooled twin turbo Boxer 6. Engine Holding Fixture will allow a full 360 degree rotation of engine, with Flywheel Lock allowing for R&R of engine. Bolts up to every Porsche and VW air cooled Boxer ever produced. From Type 1 up to 3.6L Items included in this kit are: P201, VW313 and VW215.

Call or email for lower price. Be sure to include a phone number in your email in case we need to call you back. We may have what we call "tool truck samples" or "scratch and dent" items just like this one or virtually brand new we may be able to sell at a lower price all depending upon inventory levels.
Feel free to call our toll free number 877 938 6657. Canada please email.
Heavy Duty Bench Clamp 139.99
313 Volkswagen Porsche Tool Designed for to securely carry the full weight of an air cooled twin turbo Boxer 6 Tool Number VW 313 Properly suited for a work bench.
Engine Holding Fixture 229.00
Engine Holder P201 Designed to securely bolt up to every Porsche and VW air cooled engine ever produced. Please note: This item is included in the complete kit also.
Cam Master Kit for Porsche 499.00
CAM KIT for PORSCHE
Cam Master Kit part P 260 Normally $639.00

Contains same as factory parts:
9612 1pc (P 253) normally $248.00
9634 2pc (P 255) normally $92.95/ each
9611 4pc (P 256) normally $198.95
9595 , 9595/1 set of 2 pins (P 258) normally $42.95

This exclusive cam master kit is specially assembled for the Master Porsche
Technician, independent or otherwise. The kit consists of the factory correct tools 
needed for Setting and Retaining cam timing during routine "on the car" 
maintenance of 996 engines up through 2001 and Boxster engines up through 2002. 
ZDMAK offers this fully equipped master kit with all of the tools necessary for 
complete and simultaneous security of both the left and right side of the engine. 

P 253 = Bar for setting cam timing.
P 255 = Jig for retaining cam timing in order to remove the valve cover.
P 256 = Fixture for securing cam shafts when valve cover is removed. 
P 258 = Pins for locking cam shaft pulley & torque converter.
Crowsfoot Socket 46mm 68.00
Socket Number P203 Crucial for R&R of camshaft nut. To be used in conjunction with tool P202
Porsche Repair Sockets (2) 107.00
Set of TWO tools including P203 and P202 Socket: Used to secure the cam shaft from rotating during R&R of cam shaft nut, to be used in conjunction with P203 above. Crucial when adjusting valves or setting cam timing. 911 (65 80)
Cam Socket 39.99
Socket Number P202 Used to secure the cam shaft from rotating during R&R of cam shaft nut, to be used in conjunction with P203. Crucial when adjusting valves or setting cam timing. 911 (65 80). Drive size of Socket is 1/2 inch.
P207 Gauge Holder * Z Block 39.50
Dial Gauge Holder Z Block Same as Porsche P207 Used for accurate adjustment of valves. Made from high grade aluminum with an anodize finish. Comes equipped with a 50mm dial indicator extension pin. Applicable: 911, 930.
Special Adaptor Ring * 152.00
New Porsche Adaptor Ring
For the budget minded Porsche & VW air cooled engine rebuilder...Check it out.....
This Ring (same as the one equipped on the factory style Engine Holding Fixture P201)
is void of any holding or securing tubes.
This adaptor ring is specifically designed to mate the engine case straight to any universal engine stand, using four 3/8" Bolts,
thus allowing for a full 360 degree rotation of the engine.
This ring is designed to bolt up to every Porsche and VW fully dressed air cooled engine ever produced.
It is machined with all the necessary reliefs and/or notches to allow for clearance of all engine parts, including the flywheel and its respective lock tool (VW Flywheel lock 215). Call Zdmak 877 938 6657.
Ball Joint Pin Wrench Socket 53.25
Porsche Reference Number for this tool is P280B. ZDMAK Number P210
Pin Wrench Socket with 1/2" drive and a pin reinforcement sleeve, needed for the proper R&R of ball joint nuts w/o damage to the Pin Wrench Socket or nut. 911 Porsche 1965 89 912, 914
Pulley/Fan Belt Pin Wrench 34.95
This Pulley Wrench is used for securing the generator from rotating during R&R of pulley or fan belt. Applicable: Porsche model 911 1975 and newer. (Please note: The Porsche ref. number for this item would be P208B)
Camshaft Bar 85.00
Camshaft Tool Same as Porsche 9191 Cam bar used to secure the camshaft from rotating during R&R of camshaft nut. Needed when adjusting valves or setting cam timing 911 (80 89)
Sprocket Holder 45.00
Same as Porsche Tool 9200 Locking Bar needed to properly secure the balance shaft sprocket from rotating during R&R of retaining bolt. Applicable: Porsche 944.
(3) Tools for Porsche 183.00
Set three (3) tools for Porsche
Camshaft Tool Same as Porsche 9191 Cam bar used to secure the camshaft from rotating during R&R of camshaft nut. Needed when adjusting valves or setting cam timing 911 (80 89)

Crowfoot Socket Number P203 Crucial for R&R of camshaft nut. 
To be used in conjunction with tool P202 

Socket Number P202 Used to secure the cam shaft from rotating during R&R of cam shaft nut, to be used in conjunction with P203. Crucial when adjusting valves or setting cam timing. 911 (65 80). Drive size of Socket is 1/2 inch.

Pictures are for reference only not to scale.

You will get all three tools with this purchase.
944 Flywheel Lock 34.99
Flywheel Lock needed to stop the motor from rotating during R&R of crank shaft bolt or motor. Porsche Factory ref: 000 721 920 60 Applicable: Porsche 944.
Oil Seal Arbor Porsche 141.00
Arbor needed for the proper installation of oil seal on flywheel side of crankshaft. Applicable: Porsche model 911 ?78 ?94, 928, 944, 968.
Eccentric Adjuster 24.95
P221 Eccentric Adjuster Same as Porsche 9171 Adjuster needed for Toe In of rear suspension. Applicable: Porsche model 911, 924, 944.
Alignment Pin Drift 21.00
Same as Porsche Tool 9215 Alignment Pin crucial in order to properly reinstall the oil filter/water intercooler housing. Not using this Alignment Pin may cause misalignment during this procedure, which may lead to the oil pressure relief valve sticking and ultimately engine damage. Applicable: Porsche model 944 1983 ?86.
Rivet Driver Hubcap Tool 27.50
Rivet Driver P217 Driver needed to properly secure spring clips onto the rim which holds the hubcap on the wheel. Applicable: Correct wheel setup for all Porsche 356 models with drum brakes and VW 1967 and older. The end w/o a "divot" in it gets secured into a vise which should be secured onto a workbench. You hold the steel wheel over the vertical standing Rivet Tool and place a rivet into the divot end of the tool.
Then, BLAMO with a hammer, thus securing Hub Cap steel spring onto the steel wheel via the rivet. When the rivet is secured into the steel wheel, you have to flare out the back end of it so the rivet doesnt work its way out.
Oil Seal Arbor 58.75
P216 Oil Seal Tool Arbor needed for the proper installation of oil seal on pulley side of crank shaft. Applicable: Porsche model 911 ?1965 ?89.
P215 Oil Seal Arbor 118.50
Arbor needed for the proper installation of oil seal on flywheel side of crankshaft. Applicable: Porsche model 911 ?65 ?77.
Oil Seal Arbor 42.00
P231 Oil Seal Arbor needed for the proper installation of the balance shaft oil seal. Applicable: Porsche model 944.
Pulley Wrench Fan Belt Tool 30.00
P208 Pulley Wrench For securing the generator from rotating during R&R of pulley or fan belt. 911 (65 74)
Metric Wrench 4 Piece Set 60.00
Spanner Wrench Set needed for R&R This 4 pack set includes (1) each of the following wrench sizes: 27mm, 30mm, 32mm, 36mm. Some pplications include: Porsche models 911, 930, 914 6, 944, 968. This is a German Car Specail * This set is great for the European Automotive Technician. Very Handy Tools!
Chain Sprocket Tool 36.50
P204 Chain Sprocket Tool Used for securing the chain sprocket and preventing chain slippage this tool is important when replacing tensioners or setting cam timing. 911 930.
Spoiler Spanner 19.25
Hard to find Spoiler Spanner Wrench 996 PIN WRENCH Spanner 911 Turbo Spoiler. Quality tool Made in Europe.
Magnetic Box V Wrench 36.50
17mm Magnetic Box V Wrench Used for securing the top engine bolts from rotating during R&R of motor from transmission. Applicable: Porsche, VW and Ferrari models using 17mm connecting bolts with a Hex Head
Spring Compressor (Exhaust) 65.00
Valve Spring Compressor (Exhaust) Designed for On The Car R&R of Exhaust valve springs without having to remove the motor or cylinder heads. Applicable: Porsche model 911 ?65 ?89.
Spring Compressor (Intake) 65.00
Valve Spring Compressor (Intake) Porsche Number P7i Designed for On The Car R&R of Intake valve springs w/o having to remove the motor or cylinder heads. Applicable: Porsche model 911 1965 ?89
Spring Loaded Gauge 55.00
P228 Spring Loaded Gauge Spring Loaded Gauge Displays valve spring height using pre calibrated indicators stamped onto the outside surface of this tool. Crucial for accurate valve spring adjustment. Applicable: Porsche 911. Same as Porsche P10C
Performance / Adjusment Kit 47.50
P206 Adjusment Kit 3 Piece Adjustment Tool Kit Designed to adjust the mechanical injection pump for performance emission tuning.
Tensioner Tool 13.70
P214 Used for securing tensioners in their retracted position during installation. This tool helps keep the chain timing correct during this procedure. 911 with factory tensioners (Excluding pressure fed types)
Camber Adjustment Tool 22.00
Camber Adjuster (Eccentric Insert) extremely crucial when adjusting camber of front wheels. Applicable: Porsche 911 C2 & C4.
Feeler Guage Holder and Blade 5.00
P213 Single Feeler Guage Holder and Blade for Porsche 911 Tool Comes as shown with one blade .004"
Replacement Blades 5 5.50
P213 B Set of 5 Blades Replacement blades .004"
Complete Set 10.50
P213SET Complete Set including Holder and Blade Plus 5 extra Blades
B90 Hub/Wheel Bearing R&R Kit 244.00
B90 Porsche Main Kit Hub/Wheel Bearing R&R Designed to accurately and efficiently Extract or Install the Wheel Bearing and Hub of spindle assemblies. Applicable: all 911, 912, 914, 924, 928, 944, 968 and Boxster with S.R.W.B. and I.R.S. Excluding* Hubs of 914 and 356 Sub kits are below for specific Porsche Models. Email with any questions. Pictures are for reference only.
B90 P1 Sub Kit for Porsche 177.00
Hub/Bearing Extractor and Installer Kit, 911 1965 73, 912 All, 914

Please note: Picture is for reference only. Be sure this is the kit you need before ordering. You can read more about each Porsche Kit CLICK HERE
B90 P2 Sub Kit for Porsche 177.00
Rear Hub/Bearing Extractor and Installer Kit, 911 1973 on, 924, 944, 968, All, Boxster

Please note: Picture is for reference only. Be sure this is the kit you need before ordering. You can read more about each Porsche Kit CLICK HERE
B90 P3 Sub Kit for Porsche 177.00
Hub/Bearing Extractor and Installer Kit, 911 Turbo (1990 ), 928 All

Please note: Picture is for reference only. Be sure this is the kit you need before ordering. You can read more about each Porsche Kit CLICK HERE
Oil Seal Tool 45.75
Porsche Volkswagen Tool like 204B Used for proper installation of oil seal on flywheel side of crank shaft. All VW Boxer 4.
Synchro Engagement Kit 120.00
P223 Synchro Engagement Kit Synchro Engagement Kit needed for the proper removal of synchro rings from the gear. Applicable: Porsche model 911 Turbo w/4speed ?76 ?88 3rd, 4th gears.
Synchro Engagement Kit 129.00
P224 Synchro Engagement Kit needed for the proper removal of synchro rings from the gear. Applicable: Porsche model 911 Turbo w/4speed ?76 ?88 1st, 2nd gears.
Synchro Engagement Kit 103.00
P225 Synchro Engagement Kit Synchro Engagement Kit needed for the proper removal of synchro rings from the gear. Applicable: Porsche 911 1972 ?86 3rd, 4th, 5th gears; 912 1965 THRU 71 all gears; 914 all gears.
Synchro Engagement Kit 112.24
P226 Synchro Engagement Kit needed for the proper removal of synchro rings from the gear. Applicable: Porsche model 911 1972 86 1st, 2nd gears.
36mm Flare Wrench 42.50
Special 36mm Flare Wrench like vw 179. Oil Line 12 Point Wrench for servicing Oil Lines on most 1977 and Later Porsche 911 and 944 Turbo. This tool is also used for adjusting rear suspension height on 77 and Newer Porsche 911 and for camber on most late model Volkswagen Bug.
Heavy Duty 8mm Allen 32.15
Super Duty 8mm Allen Item P243 Extra Long 3/8 Drive Socket This 8mm Extra Long Allen Socket is a solid one piece construction. Overall length is 7.75 inches. Used for R & R of some Benz Cylinder Headbolts, and some BMW C.V Joint Bolts, and Porsche Heat Exchange Exhaust sysetms 911 930 Porsche
Drift Pin 16.99
Drift Pin 4mm Number P1045X Drift needed for removing disc brake pads. This Drift is designed to press the brake pad retaining pins back w/o damage to pin or caliper. Applicable: Porsche models. Also, for a variety of other applications. (Overall length of tool is 7 inches.)
Valve Shim Plier 19.99
Valve Shim Tool Used for proper R&R of valve adjusting shims. Applicable: Overhead Cam engines with adjusting shims.
Valve Plier 18.95
Valve Stem Seal Plier 10 218A Tool is used for the proper extraction of stem seals. The inside grooves on the tips of this Plier allows the firm grip of both O.E. and aftermarket seals. Applicable: Most Overhead Cam engines.
Pilot Bearing Puller 44.50
Pilot Bearing Puller 1088 12 15mm Universal Pilot Bearing and Blind Hole bushing Puller. Important: Removing the center bolt of this puller will allow you to penetrate an I.D. as small as 12mm. Do not use on an I.D. larger than 15mm Applicable: Most European Vehicles. Excluding Suzuki and Geo
Puller 55.00
Pilot Bearing Puller 1089X 15 20mm Universal Pilot Bearing and Blind Hole bushing Puller. Important: Removing the center bolt of this puller will allow you to penetrate an I.D. as small as 15mm. Do not use on an I.D. larger than 20mm* Applicable: Most foreign and domestic mid size to full size vehicles.
Puller 39.99
Heavy Duty Pilot Bearing Blind Hole Bushing Puller 1090X 17 30mm Universal Pilot Bearing and Blind Hole bushing Puller. Important: Removing the center bolt of this puller will allow you to penetrate an I.D. as small as 17mm. Do not use on an I.D. larger than 30mm* Applicable: Medium to Heavy cars and trucks.
Relief Valve Tool 30.50
P236 Pressure Relief Valve Extractor Extractor the proper extraction of the from engine case. All Porsche VW Boxer 4
Puller 27.99
P229X Distributer Drive Gear Puller Puller used for the proper extraction of the Distributer Drive Gear from engine case. All Porsche VW Boxer 4
Starter Bushing Puller 31.50
P239 Starter Bushing Puller 12V Starter Bushing Puller 12V Models Porsche and VW Boxer 4
Starter Bushing Puller 31.50
P238 Starter Bushing Puller 6V Applicable: All Porsche and VW Boxer 4 6 Volt models.
Spring Clips 4.50
P241 Spring Clips like vw 171 Used for securing cam followers within crank case half during assembly. Applicable: Porsche model 356, 912, 914. Every VW air cooled engine.
Hazet Oil Service Tool 29.50
2169 OIL SERVICE WRENCH SOCKET
SIZE 74.5mm (DRIVE SIZE 3/8" with OUTSIDE HEX SIZE equals 27mm
APPLICATIONS INCLUDE: Some Mercedes, Audi, VW Golf, New Beetle and new body Jetta, TDI (Diesel)
and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco,
and New Beetle......Click Here to see the tool.
Gauge Holder 38.00
Dial Gauge Holder P240 Used to properly measure crank shaft flywheel and pulley end play. Can also be universally to check clearances and run out. Applicable: Most Porsche and VW air cooled engine.
Thin Wrench 32mm Open End 32.00
Extra Long 32mm Thin Wrench Number 1032T This wrench has a thickness of 8mm. We have other 32mm thin wrenches on this website, but at 20 inches long and good quality, this is the wrench we recommend.
36mm Open End Thin Wrench 32.00
Extra Long 36mm Thin Wrench Number 1032T This wrench has a thickness of 8mm. We have other 32mm thin wrenches on this website, but at 20 inches long and good quality, this is the wrench we recommend.
Special Open Socket 22mm 24.95
On Sale *
22mm Special Tube Socket
1.) Used for securing the Strut tower retaining nut of most European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench)
2.) R&R of Oxygen Sensor.
Also for R&R of some Mercedes Diesel injectors ( OM604, 605 & 606).
Details: For removing and installing front strut unit on VW Golf up to 1988, Jetta up to 87, Scirocco, Audi 80 and Golf 3 from 1993 newer, Passat from 88 and newer, Audi 100, 200 Coupe and Quatro.
This tool is often used in conjunction with a 7mm hex wrench.
Click here for a picture of the tools in action:
Special Crowsfoot Socket 23.50
OXYGEN SENSOR Socket 4491b This is a Special 22mm Crowsfoot Socket with 3/8 Drive Used for the removal and replacement of Oxygen Sensor that are situated within a confined area. No need to snip the wires leading to the unit when all you want to do is check the sensor. Applicable: Most European Models.
Special Socket 19.99
OXYGEN SENSOR Socket 4491C 22mm Socket 3/8 Dr. used for the removal and replacement of stubborn Oxygen Sensors situated within a confined area. Applicable: Most European Models.
Thin Wrench 32 X 36mm 34.95
Thin Wrench Number 1032X36T Thin Wrench 32 X36mm with an 8mm overall thickness and an overall length of 12 inches for proper leverage. Many applications for this handy thin wrench
Ultra Long Metric Wrench Set 67.50
9 Piece Ultra Long box wrench set (metric) Ultra Long double box end wrenches are almost twice the length of a standard wrench, resulting in greater leverage, reach and control. This set features a zero degree offset and extra long, super torque box end wrenches. These wrenches meet or exceed U.S. standards and carry a lifetime guarantee. Sizes included 8X10, 9X11, 10X12, 13X14, 15X16, 17X18, 19x20, 21X22, 23X24
Heavy Duty 17mm Socket 19.95
Heavy Duty Allen 17mm Stubby Socket 1017 Heavy duty Allen socket designed specially for R&R of gearbox drain plugs. Also for a variety of other applications. 1/2 Drive Applicable: Most European Vehicles
Triple Square Set 38.99
XZN Metric Socket Set 8 Piece
OUR BEST SELLER!
These are Triple Square Sockets
XZN means Triple Square (12 point)
If your tool books call for XZN or TRIPLE SQUARE or 12 POINT, these are probably the tools you need. 
These are Short Pattern "Stubby" Sockets
Each tool is 1 1/2 inches long.
Sizes included: M4, M5, M6, M 8, M10, M12, M14 & M16
Short pattern for using when you are in a tight spot.
Sturdy compact solid one piece design.
3/8 Drive Size.
Satin Chrome with black impact tips. New S2 Alloy Steel.
These are some of the strongest drivers you will find.
Comes in the plastic carrying case.

Triple square, also known as a XZN socket, is a type of screw drive. They are commonly found on German vehicles such as BMW, Mercedes, and Volkswagen etc... 
These screws/fasteners are used in some high torque applications such as cylinder head bolts and drive train components. 
Triple square bolts are common to early Porsche and Volkswagen (CV) constant velocity joints.
Most common earlier sizes would be 6, 8, 10, and 12. 
Increasingly, triple square screws are found on other European and Asian makes of cars.
Other names for triple square screws and drivers are "Double Hex", "Double Allen", and "Aircraft Screws". 
Despite this, "Double Hex" and "Double Allen" are misnomers. The recess in these bolts is actually (as the name suggests) made of three squares, not two hexagons. 
The corners are 90 degrees, not 120 degrees. They are not double hexes, and an Allen key will not fit them properly.
911 Oil Service Tool 38.00
Porsche 911 Tool.
Hazet Oil Filter Wrench size 92mm.
With square drive nominal size 12.5 = 1/2 inch.
outside hexagon 27 mm.
15 point (inside flats or flutes)
For 911 and several other vehicles such as Saab 900, 9000 and 99 etc...
High Quality Tool Made in Germany.
P207 Gauge Holder * Z Block 39.50
Dial Gauge Holder Z Block Same as Porsche P207 Used for accurate adjustment of valves. Made from high grade aluminum with an anodize finish. Comes equipped with a 50mm dial indicator extension pin. Applicable: 911, 930.
8 Piece XZN Set 38.99
XZN Metric Socket Set 8 Piece
OUR BEST SELLER!
These are Triple Square Sockets
XZN means Triple Square (12 point)
If your tool books call for XZN or TRIPLE SQUARE or 12 POINT, these are probably the tools you need. 
These are Short Pattern "Stubby" Sockets
Each tool is 1 1/2 inches long.
Sizes included: M4, M5, M6, M 8, M10, M12, M14 & M16
Short pattern for using when you are in a tight spot.
Sturdy compact solid one piece design.
3/8 Drive Size.
Satin Chrome with black impact tips. New S2 Alloy Steel.
These are some of the strongest drivers you will find.
Comes in the plastic carrying case.

Triple square, also known as a XZN socket, is a type of screw drive. They are commonly found on German vehicles such as BMW, Mercedes, and Volkswagen etc... 
These screws/fasteners are used in some high torque applications such as cylinder head bolts and drive train components. 
Triple square bolts are common to early Porsche and Volkswagen (CV) constant velocity joints.
Most common earlier sizes would be 6, 8, 10, and 12. 
Increasingly, triple square screws are found on other European and Asian makes of cars.
Other names for triple square screws and drivers are "Double Hex", "Double Allen", and "Aircraft Screws". 
Despite this, "Double Hex" and "Double Allen" are misnomers. The recess in these bolts is actually (as the name suggests) made of three squares, not two hexagons. 
The corners are 90 degrees, not 120 degrees. They are not double hexes, and an Allen key will not fit them properly.
Valve Plier 18.95
Valve Stem Seal Plier 10 218A Tool is used for the proper extraction of stem seals. The inside grooves on the tips of this Plier allows the firm grip of both O.E. and aftermarket seals. Applicable: Most Overhead Cam engines.
911 Easy Rider Tool 89.00
Easy Rider* Height Adjustment Lever
This a "Brand New" special service tool P244 Developed to aid the technician with safe and easy ride height adjustment of rear torsion arms and/or general adjusting of Aftermarket Adjustable Spring Plates. The inherent design of this tool acts as an extension of the trailing arm by latching onto it at two hook points. The end of the protruding tool is supported by a roll around floor jack. You simply pre load the suspension and are able to maintain the travel in any desired position w/o having to use chains, which may slip, is very dangerous and generally non professional. Prior to this new Ride Height Adjusting Lever, a combo set up set up was used. Whereby, wrapping a chain onto the vehicle, sling it around the trailing arm, placing a jack between the chain and trailing arm. Thereby, rendering the jack to react against the chain/trailing arm. If the chain breaks or slips, BLAMO !
Spring Compressor (Intake) 65.00
Valve Spring Compressor (Intake) Porsche Number P7i Designed for On The Car R&R of Intake valve springs w/o having to remove the motor or cylinder heads. Applicable: Porsche model 9111965 ?89
Rivet Driver Hubcap Tool 27.50
Rivet Driver P217 Driver needed to properly secure spring clips onto the rim which holds the hubcap on the wheel. Applicable: Correct wheel setup for all Porsche 356 models with drum brakes and VW 1967 and older. The end w/o a "divot" in it gets secured into a vise which should be secured onto a workbench. You hold the steel wheel over the vertical standing Rivet Tool and place a rivet into the divot end of the tool.
Then, BLAMO with a hammer, thus securing Hub Cap steel spring onto the steel wheel via the rivet. When the rivet is secured into the steel wheel, you have to flare out the back end of it so the rivet doesnt work its way out.
Ball Joint Pin Wrench Socket 53.25
Porsche Reference Number for this tool is P280B. ZDMAK Number P210
Pin Wrench Socket with 1/2" drive and a pin reinforcement sleeve, needed for the proper R&R of ball joint nuts w/o damage to the Pin Wrench Socket or nut. 911 Porsche 1965 89 912,914
Oil Seal Tool 45.75
Porsche Volkswagen Tool like 204B Used for proper installation of oil seal on flywheel side of crank shaft. All VW Boxer 4.
944 Flywheel Lock 34.99
Flywheel Lock needed to stop the motor from rotating during R&R of crank shaft bolt or motor. Porsche Factory ref: 000 721 920 60 Applicable: Porsche944.
Sprocket Holder 45.00
Same as Porsche Tool 9200 Locking Bar needed to properly secure the balance shaft sprocket from rotating during R&R of retaining bolt. Applicable: Porsche 944.
MetricWrench 4 Piece Set 60.00
Spanner Wrench Set needed for R&R This 4 pack set includes (1) each of the following wrench sizes: 27mm, 30mm, 32mm, 36mm. Some pplications include: Porsche models 911, 930, 914 6, 944, 968. This is a German Car Specail * This set is great for the European Automotive Technician. Very Handy Tools!
Performance / Adjusment Kit 47.50
P206 Adjusment Kit 3 Piece Adjustment Tool Kit Designed to adjust the mechanical injection pump for performance emission tuning.
Cam Socket 39.99
Socket Number P202 Used to secure the cam shaft from rotating during R&R of cam shaft nut, to be used in conjunction with P203. Crucial when adjusting valves or setting cam timing. 911 (65 80). Drive size of Socket is 1/2 inch.
Special Adaptor Ring * 152.00
New Porsche Adaptor Ring
For the budget minded Porsche & VW air cooled engine rebuilder...Check it out.....
This Ring (same as the one equipped on the factory style Engine Holding Fixture P201)
is void of any holding or securing tubes.
This adaptor ring is specifically designed to mate the engine case straight to any universal engine stand, using four 3/8" Bolts,
thus allowing for a full 360 degree rotation of the engine.
This ring is designed to bolt up to every Porsche and VW fully dressed air cooled engine ever produced.
It is machined with all the necessary reliefs and/or notches to allow for clearance of all engine parts, including the flywheel and its respective lock tool (VW Flywheel lock 215). Call Zdmak 877 938 6657.
Tensioner Tool 13.70
P214 Used for securing tensioners in their retracted position during installation. This tool helps keep the chain timing correct during this procedure. 911 with factory tensioners (Excluding pressure fed types)
Eccentric Adjuster 24.95
P221Eccentric Adjuster Same as Porsche 9171 Adjuster needed for Toe In of rear suspension. Applicable: Porsche model 911, 924, 944.
Feeler Guage Holder and Blade 5.00
P213 Single Feeler Guage Holder and Blade for Porsche 911 Tool Comes as shown with one blade .004"
Tie Rod Tool 35.50
Puller P266HX Separator used for disassembly of Pitman arm type tie rod ends without tearing the boots. Opening size is 18mm. Most VW Audi Late Porsche models.
Click here for a Diagram on this tool.
Tie Rod Tool 64.00
Tie Rod Tool VW 1014 Separator used for disassembly of pitman arm type tie rod ends without tearing the ball joint boots. Opening size is 25mm. Most VW Audi & Late Porsche models.
Click here for a Diagram on this tool.
Hub Wheel Bearing R&R Kit 244.00
B90 Porsche Main Kit Hub/Wheel Bearing R&R Designed to accurately and efficiently Extract or Install the Wheel Bearing and Hub of spindle assemblies. Applicable: all 911, 912, 914, 924, 928, 944, 968 and Boxster with S.R.W.B. and I.R.S. Excluding* Hubs of 914 and 356 Sub kits are below for specific Porsche Models. Email with any questions. Pictures are for reference only.
Professional Engine Holder Complete 349.00
Engine Holding Fixture Designed to securely carry the entire weight of a fully dressed air cooled twin turbo Boxer 6. Engine Holding Fixture will allow a full 360 degree rotation of engine, with Flywheel Lock allowing for R&R of engine. Bolts up to every Porsche and VW air cooled Boxer ever produced. From Type 1 up to 3.6L Items included in this kit are: P201, VW313 and VW215.

Call or email for lower price. Be sure to include a phone number in your email in case we need to call you back. We may have what we call "tool truck samples" or "scratch and dent" items just like this one or virtually brand new we may be able to sell at a lower price all depending upon inventory levels.
Feel free to call our toll free number 877 938 6657. Canada please email.
Synchro Engagement Kit 103.00
P225 Synchro Engagement Kit Synchro Engagement Kit needed for the proper removal of synchro rings from the gear. Applicable: Porsche 911 1972 ?86 3rd, 4th, 5th gears; 912 1965 THRU 71 all gears; 914 all gears.
Panel Popper Set of 5 16.50
DOOR PANEL & UPHOLSTERY TOOLS Complete Panel "Popper" Tool Set
Super Tools for Auto Interior Work
This 5 Piece Set of plastic pry pullers is perfect for working on those expensive panels on car interiors. It will also help work loose plastic decorative inserts, door moldings and countless other pieces on todays modern and many vintage cars.
* You may have seen other sets like this, but they only come with 4 pieces... This set has 5 pieces with more features plus the quality of this set is better (stronger and more durable) than other being sold,
making this a much better deal.
This set comes in a Clam Shell Protective Container.
Tie Rod Tool 35.50
Puller P266HX Separator used for disassembly of Pitman arm type tie rod ends without tearing the boots. Opening size is 18mm. Most VW Audi Late Porsche models.
Click here for a Diagram on this tool.
911 Tool Set 119.99
Set of 4 Tools for 911.
You get the TWO SOCKETS P202 and P203 ABOVE and the FEELER GUAGE SET
The Socket set is used to secure the cam shaft from rotating during R&R of cam shaft nut. Crucial when adjusting valves or setting cam timing. 911.

This Feeler Guage set includes P213 Holder with blade and Blade Pack of 5 extra Blades size .004
Synchro Engagement Kit 112.24
P226 Synchro Engagement Kit needed for the proper removal of synchro rings from the gear. Applicable: Porsche model 911 1972 86 1st, 2nd gears.
Triple Square Socket 3357 13.99
Drain Plug Socket This is a Special Tamperproof Transmission Drain Plug Socket. Triple Square ( 12 Point XZN ) for VW and Audi with ZF Transmissions Same as Volkswagen Tool 3357. For Porsche Boxster and Audi A4, A6 and Passat
Spring Compressor (Exhaust) 65.00
Valve Spring Compressor (Exhaust) Designed for On The Car R&R of Exhaust valve springs without having to remove the motor or cylinder heads. Applicable: Porsche model911 ?65 ?89.
Crowsfoot Socket 46mm 68.00
Socket Number P203 Crucial for R&R of camshaft nut. To be used in conjunction with tool P202
Heavy Duty 8mm Allen 32.15
Super Duty 8mm Allen Item P243 Extra Long 3/8 Drive Socket This 8mm Extra Long Allen Socket is a solid one piece construction. Overall length is 7.75 inches. Used for R & R of some Benz Cylinder Headbolts, and some BMW C.V Joint Bolts, and Porsche Heat Exchange Exhaust sysetms 911 930 Porsche
Camshaft Bar 85.00
Camshaft Tool Same as Porsche 9191 Cam bar used to secure the camshaft from rotating during R&R of camshaft nut. Needed when adjusting valves or setting cam timing 911 (80 89)
Synchro Engagement Kit 120.00
P223 Synchro Engagement Kit Synchro Engagement Kit needed for the proper removal of synchro rings from the gear. Applicable: Porsche model 911 Turbo w/4speed ?76 ?88 3rd, 4th gears.
Heavy Duty 17mm Socket 19.95
Heavy Duty Allen 17mm Stubby Socket 1017 Heavy duty Allen socket designed specially for R&R of gearbox drain plugs. Also for a variety of other applications. 1/2 DriveApplicable: Most European Vehicles
Tie Rod Tool 64.00
Tie Rod Tool VW 1014 Separator used for disassembly of pitman arm type tie rod ends without tearing the ball joint boots. Opening size is 25mm. Most VW Audi & Late Porsche models.
Click here for a Diagram on this tool.
Synchro Engagement Kit 129.00
P224 Synchro Engagement Kit needed for the proper removal of synchro rings from the gear. Applicable: Porsche model 911 Turbo w/4speed ?76 ?88 1st, 2nd gears.
Complete Set 10.50
P213SET Complete Set including Holder and Blade Plus 5 extra Blades
Replacement Blades 5 5.50
P213 B Set of 5 Blades Replacement blades .004"
Valve Plier Set of 2 37.50
Set of 2 tools: Valve Plier (top) used for the proper extraction of stem seals. The inside grooves on the tips of this Plier allows the firm grip of both O.E. and aftermarket seals Applicable: Most Overhead Cam engines.
Plus: Shim Plier used for proper R&R of valve adjusting shims. Applicable: Overhead Cam engines with adjusting shims.
Spoiler Spanner 19.25
Spoiler Spanner Wrench 996 PIN WRENCH Spanner 911 Turbo Spoiler
Porsche Radio Removal Tools 8.99
Radio Removal Keys for Porsche
As good or better than the factory tools...
Please note the rubber on the handle for a better grip.
Appl: Turbo GT, GT2, GT3, Boxster,
Cayenne 911, 996 , 987, Carrera etc...
Same as Porsche ref: 000 721 957 01

NOTE : KEYS WILL ALSO WORK ON ALL NEWER MERCEDES
For Mercedes 1997 and newer.

Used to remove radio, (Becker) climate controls and Nav system.
Applicable most 97 and newer most
S, C, E, CL, SL, SLK, ML, G class vehicles.
XZN Triple Square Set 24.99
XZN Set of 4 "Triple Square" Tools.
This set includes sizes:
6mm, 8mm, 10mm & 12mm bits
Drive size is 3/8"
A very handy set for the German car Technician. You get all four (4) tools with this purchase.

Triple square, also known as a XZN socket, is a type of screw drive. They are commonly found on German vehicles such as BMW, Mercedes, and Volkswagen etc... These screws/fasteners are used in some high torque applications such as cylinder head bolts and drive train components. Triple square bolts are common to early Porsche and Volkswagen (CV) constant velocity joints. Increasingly, triple square screws are found on other European and Asian makes of cars. Other names for this type of triple square screws and drivers are "Double Hex", "Double Allen", and "Aircraft Screws". Despite this, "Double Hex" and "Double Allen" are misnomers. The recess in these bolts is actually (as the name suggests) made of three squares, not two hexagons. The corners are 90 degrees, not 120 degrees. They are not double hexes, and an Allen key will not fit them properly.

These are XZN Triple Square Tools. XZN means Triple Square or 12 point. If your tool book calls for XZN or Triple Square or 12 Point, these are probably the tools you need. Satin Chrome with New S2 Alloy Steel. These are some of the strongest drivers you will find.
Chain Sprocket Tool 36.50
P204 Chain Sprocket Tool Used for securing the chain sprocket and preventing chain slippage this tool is important when replacing tensioners or setting cam timing. 911 930.
Hazet Oil Service Tool 29.50
Oil service Wrench 74mm with 14 Points (inside flats flutes).
THIS ITEM HAS BOTH DRIVE SIZES 3/8" (10mm)
AND OUTSIDE HEX SIZE = 27mm
Some applications include: Mercedes, Audi, VW Golf,
and new body Jetta, TDI (Diesel) and the following gas vehicles;
Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle.
Mercedes M104, M110, M111, M119, M120 C, E
Porsche 944 and 924.
Some Toyota (Filter 08922 0211 etc...)
Can also be used on BMW Top of housing 1.9L M44
Super High Quality Original Factory Tool Made in Germany!
Click here to see a detailed Application Chart Measure filter diameter canister diameter or Check your manuals for details and size needed.
Camber Adjustment Tool 22.00
Camber Adjuster (Eccentric Insert) extremely crucial when adjusting camber of front wheels. Applicable: Porsche 911 C2 & C4.
Valve Spring Tool and Bridge 149.99
Valve Spring Tools Set including: VA6010 Valve Spring Compressor Bar Same as Volkswagen Tool Number VW 541/1 Used for R&R of valve spring or rocker arm With this tool the job can be done with the cylinder head on or off the car. Used in conjunction with tool Bridge Applicable: 924 / 944 VW AUDI 4 5 Cyl. VA6022 Support Bridge Same as VW Tool 2036 Used for R&R of valve spring or rocker arm Used in conjunction with tool VW541/1 Applicable: Model 924. VW / AUDI 4 5 Cyl.
30mm Thin Wall Deep Socket 28.99
Specially designed 30mm thin walled 12 point, deep socket.
Used for 911 Drive Shaft.
Pressure Adaptor 24.95
Pressure Adaptor 1018 Used for pressuring the master cylinder or clutch slave cylinder reservoirs. Used in conjunction with a pressure bleeder. Comes with a 1/4 18 NPT threaded opening. Applicable:Most European models.
German Car Special 2 Thin Wrenches 36.50
"Long" Pattern Thin Wrenches
Set of Two (2)
One of each size: 36MM and 32mm
Brand New "Long Thin Wrenches"
Many applications for these two tools,
especially for European cars.
Overall length of 15 inches.
Thickness of each wrench is 1/4" (6.35mm)
Some applications include: Mercedes and BMW R&R of fan clutch hub nut.
Porsche 32mm used for R&R of tie rods Model 911 Turbo, 89 76
36mm Needed for proper adjustment of rear ride height 911 , 89 77 etc...
Oil Filter Wrench 74mm 13.99
Oil service Wrench 74mm with 14 Points (inside flats flutes).
This is an excellent deal. This tool has 2 bonus screws for more strength if needed.
The screws are kept in the holes at the top when not in use and can be used inserted into the side holes making the tool more effective.
Some applications include: Mercedes, Audi, VW Golf, and New body Jetta, TDI (Diesel) and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle. Mercedes M104, M110, M111, M119, M120 C, E etc...
Porsche 944 and 924. Some Toyota. Check your manuals for details and size needed. Measure filter diameter or canister diameter.
See chart below.
bullet Audi Coupe 81 87
bullet Audi Coupe Q 20v 90 91
bullet Audi Fox 73 79
bullet Audi 100 89 91
bullet Audi 100Q 89 91
bullet Audi 4000 4 Cyl 80 87
bullet Audi 4000 5 Cyl 80 81
bullet Audi 4000 Q 84 87
bullet Audi 5000 78 88
bullet Audi 5000 Q 87 88
bullet Audi 80 88 90
bullet Audi 90 88 90
bullet Audi 90 Q 20v 90 92
bullet BMW 325 85 88
bullet BMW 325e 84 88
bullet BMW 325es 86 87
bullet BMW 325i Sedan 87 91
bullet BMW 325i Cabriolet 87 93
bullet BMW 325is Coupe 87 91
bullet BMW 325ix 88 91
bullet BMW 525i 89 90
bullet BMW 528e 82 88
bullet Mercedes 190E 2.3 1985 1993
bullet Mercedes 190E 2.6 1987 1993
bullet Mercedes 260E 1987 1989
bullet Mercedes 300CE 1988 1989
bullet Mercedes 300E 2.6 1990 1992
bullet Mercedes 300E 1986 1992
bullet Mercedes 300E 4 Matic 1990 1993
bullet Mercedes 300SE 1988 1991
bullet Mercedes 300SEL 1988 1991
bullet Mercedes 300TE Wagon 1988 1992
bullet Mercedes 300TE 4 Matic Wagon 1990 1993
bullet Porsche 924 77 82
bullet Porsche 924 Turbo 80 82
bullet Porsche Cayenne S 03 04
bullet Porsche Cayenne Turbo 03 04
bullet Porsche 911/996 Carrera/2 98 04
bullet Porsche 911/996 Carrera/4 99 04
bullet Porsche 911/996 GT3 04 04
bullet Porsche 911 Twin Turbo 01 04
bullet Porsche Carrera GT 04 04
bullet Porsche Boxster 97 04
bullet Porsche 911 Turbo 1991 1994
bullet Porsche 924S 1986 1988
bullet Porsche 944 1983 1989
bullet Porsche 944S 1987 1988
bullet Porsche 944S2 1989 1991
bullet Porsche 944 Turbo 1986 1991
bullet Porsche 968 1992 1995
bullet Porsche 928 78 84
bullet Porsche 928 32 85 95V
bullet Porsche 911/993 Carrera/2 1995 1998
bullet Porsche 911/993 Carrera/4 1995 1998
bullet Porsche 911 Twin Turbo 1995 1999
bullet Volkswagen Dasher 74 81
bullet Volkswagen Fox 87 93
bullet Volkswagen Golf GL/GT 85 92
bullet Volkswagen Golf III GL 93 94
bullet Volkswagen Golf GTI 8/16V 85 92
bullet Volkswagen Golf III GTI 93 94
bullet Volkswagen Jetta 80 84
bullet Volkswagen Jetta GL 85 92
bullet Volkswagen Jetta(Canada) 93 99
bullet Volkswagen Jetta Carat 85 92
bullet Volkswagen Jetta III GL 93 94
bullet Volkswagen Jetta GLI 84 88
bullet Volkswagen Jetta GLI 16V
bullet Volkswagen Jetta III GLS
bullet Volkswagen Passat 16V 90 93
bullet Volkswagen Passat GL 95 97
bullet Volkswagen Quantum 4 Cyl 82 85
bullet Volkswagen Quantum 5 Cyl 83 88
bullet Volkswagen Rabbit 75 84
bullet Volkswagen Rabbit Convertible 79 87
bullet Volkswagen Rabbit Cabriolet 88 93
bullet Volkswagen Rabbit GTI 83 84
bullet Volkswagen Scirocco 75 88
bullet Volkswagen Scirocco 16V 86 88
bullet Volkswagen Van Water Cool 83 92
bullet Volkswagen Van Syncro 86 92 This tool can be used on the following filters
bullet Audi, VW: 070 115 561, 056 115 561G, 034 115 561A
bullet BMW: 11 42 1 266 773
bullet Mecedes: 102 184 01 01
bullet Porsche: 996 107 225 52, 993 207 201 02, 993 107 203 03, 928 107 201 05,
bullet 944 107 201 08
32mm Open End Thin Wrench 19.99
32mm Open End Thin Wrench Long Pattern Thin Wrench with an overall length of 15 inches. The thickness of this wrench is 1/4" (6.35mm). Some applications include: Mercedes and BMW R&R of fan clutch hub nut. Porsche 32mm used for R&R of tie rods Model 911 Turbo 1976 89 etc... This is a great tool for working on European and Asian vehicles.
Alternator Socket 15.99
Alternator Socket For mounting the V belt pulley (slip clutch pulley) at the alternator (manuals call it a generator), especially for T.D.I. VW Golf III, Vento, Passat and AUDI A 3
17MM outside dia. Length 30mm. Also for Boxster Alternators with free wheeling Pulleys. The Porsche Number for this tool would be 2592 or PNA 721 048. See repair Group 27 Porsche Bulletins.
Valve Spring Tool 69.99
Valve Spring Compressor Bar VA6010 Used for R&R of valve spring or rocker arm VW AUDI 4 / 5 Cylinder. With this tool the job can be done with the cylinder head on or off the car. Used in conjunction with tool VA6022 below Applicable: 924 / 944 Reference VW Tool Number VW541/1
Support Bridge 75.00
VA6022 Support Bridge Used for R&R of valve spring or rocker arm. Used in conjunction with tool VA6010 (above). Applicable: Model 924. VW / AUDI 4 5 Cyl. Reference VW Tool 2036
Flexible Driver Set 4 27.50
You will receive 4 all four tools with this set. Included are 3 flex shaft (female) nut drivers 6, 7, and 8mm
Plus a very handy 1/4 inch (male) Driver.
Metric Hex Stubbies 38.00
Metric Hex Stubbies (short pattern) 1/4 Drive 9 Piece Set. Similar to the Hex tools made popular by Hazet Stubby Hex Metric Sockets in the most Popular smaller sizes.
EACH TOOL IS ONE INCH LONG.
These are the sturdy one piece design.
Hex / Allen sockets sizes included: 2mm, 2.5mm, 3, 4, 5, 6, 7, 8, 10mm.
S2 Alloy steel THE STRONGEST DRIVERS AVAILABLE! Heat treated to 56 to 62 RC. Satin Chrome plating. Comes in the plastic case.
This set is great and is a must for working on MERCEDES, BMW, VW, AUDI or PORSCHE. These are very strong and fit in very small areas. Great when disassembling or assembling engine/transmission. Real time savers!
8 Piece XZN Set 38.99
XZN Metric Socket Set 8 Piece
OUR BEST SELLER!
These are Triple Square Sockets
XZN means Triple Square (12 point)
If your tool books call for XZN or TRIPLE SQUARE or 12 POINT, these are probably the tools you need. 
These are Short Pattern "Stubby" Sockets
Each tool is 1 1/2 inches long.
Sizes included: M4, M5, M6, M 8, M10, M12, M14 & M16
Short pattern for using when you are in a tight spot.
Sturdy compact solid one piece design.
3/8 Drive Size.
Satin Chrome with black impact tips. New S2 Alloy Steel.
These are some of the strongest drivers you will find.
Comes in the plastic carrying case.

Triple square, also known as a XZN socket, is a type of screw drive. They are commonly found on German vehicles such as BMW, Mercedes, and Volkswagen etc... 
These screws/fasteners are used in some high torque applications such as cylinder head bolts and drive train components. 
Triple square bolts are common to early Porsche and Volkswagen (CV) constant velocity joints.
Most common earlier sizes would be 6, 8, 10, and 12. 
Increasingly, triple square screws are found on other European and Asian makes of cars.
Other names for triple square screws and drivers are "Double Hex", "Double Allen", and "Aircraft Screws". 
Despite this, "Double Hex" and "Double Allen" are misnomers. The recess in these bolts is actually (as the name suggests) made of three squares, not two hexagons. 
The corners are 90 degrees, not 120 degrees. They are not double hexes, and an Allen key will not fit them properly.
Oil Filter Wrench 74mm 13.99
Oil service Wrench 74mm with 14 Points (inside flats flutes).
This is an excellent deal. This tool has 2 bonus screws for more strength if needed.
The screws are kept in the holes at the top when not in use and can be used inserted into the side holes making the tool more effective.
Some applications include: Mercedes, Audi, VW Golf, and New body Jetta, TDI (Diesel) and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle. Mercedes M104, M110, M111, M119, M120 C, E etc...
Porsche 944 and 924. Some Toyota. Check your manuals for details and size needed. Measure filter diameter or canister diameter.
See chart below.
bullet Audi Coupe 81 87
bullet Audi Coupe Q 20v 90 91
bullet Audi Fox 73 79
bullet Audi 100 89 91
bullet Audi 100Q 89 91
bullet Audi 4000 4 Cyl 80 87
bullet Audi 4000 5 Cyl 80 81
bullet Audi 4000 Q 84 87
bullet Audi 5000 78 88
bullet Audi 5000 Q 87 88
bullet Audi 80 88 90
bullet Audi 90 88 90
bullet Audi 90 Q 20v 90 92
bullet BMW 325 85 88
bullet BMW 325e 84 88
bullet BMW 325es 86 87
bullet BMW 325i Sedan 87 91
bullet BMW 325i Cabriolet 87 93
bullet BMW 325is Coupe 87 91
bullet BMW 325ix 88 91
bullet BMW 525i 89 90
bullet BMW 528e 82 88
bullet Mercedes 190E 2.3 1985 1993
bullet Mercedes 190E 2.6 1987 1993
bullet Mercedes 260E 1987 1989
bullet Mercedes 300CE 1988 1989
bullet Mercedes 300E 2.6 1990 1992
bullet Mercedes 300E 1986 1992
bullet Mercedes 300E 4 Matic 1990 1993
bullet Mercedes 300SE 1988 1991
bullet Mercedes 300SEL 1988 1991
bullet Mercedes 300TE Wagon 1988 1992
bullet Mercedes 300TE 4 Matic Wagon 1990 1993
bullet Porsche 924 77 82
bullet Porsche 924 Turbo 80 82
bullet Porsche Cayenne S 03 04
bullet Porsche Cayenne Turbo 03 04
bullet Porsche 911/996 Carrera/2 98 04
bullet Porsche 911/996 Carrera/4 99 04
bullet Porsche 911/996 GT3 04 04
bullet Porsche 911 Twin Turbo 01 04
bullet Porsche Carrera GT 04 04
bullet Porsche Boxster 97 04
bullet Porsche 911 Turbo 1991 1994
bullet Porsche 924S 1986 1988
bullet Porsche 944 1983 1989
bullet Porsche 944S 1987 1988
bullet Porsche 944S2 1989 1991
bullet Porsche 944 Turbo 1986 1991
bullet Porsche 968 1992 1995
bullet Porsche 928 78 84
bullet Porsche 928 32 85 95V
bullet Porsche 911/993 Carrera/2 1995 1998
bullet Porsche 911/993 Carrera/4 1995 1998
bullet Porsche 911 Twin Turbo 1995 1999
bullet Volkswagen Dasher 74 81
bullet Volkswagen Fox 87 93
bullet Volkswagen Golf GL/GT 85 92
bullet Volkswagen Golf III GL 93 94
bullet Volkswagen Golf GTI 8/16V 85 92
bullet Volkswagen Golf III GTI 93 94
bullet Volkswagen Jetta 80 84
bullet Volkswagen Jetta GL 85 92
bullet Volkswagen Jetta(Canada) 93 99
bullet Volkswagen Jetta Carat 85 92
bullet Volkswagen Jetta III GL 93 94
bullet Volkswagen Jetta GLI 84 88
bullet Volkswagen Jetta GLI 16V
bullet Volkswagen Jetta III GLS
bullet Volkswagen Passat 16V 90 93
bullet Volkswagen Passat GL 95 97
bullet Volkswagen Quantum 4 Cyl 82 85
bullet Volkswagen Quantum 5 Cyl 83 88
bullet Volkswagen Rabbit 75 84
bullet Volkswagen Rabbit Convertible 79 87
bullet Volkswagen Rabbit Cabriolet 88 93
bullet Volkswagen Rabbit GTI 83 84
bullet Volkswagen Scirocco 75 88
bullet Volkswagen Scirocco 16V 86 88
bullet Volkswagen Van Water Cool 83 92
bullet Volkswagen Van Syncro 86 92 This tool can be used on the following filters
bullet Audi, VW: 070 115 561, 056 115 561G, 034 115 561A
bullet BMW: 11 42 1 266 773
bullet Mecedes: 102 184 01 01
bullet Porsche: 996 107 225 52, 993 207 201 02, 993 107 203 03, 928 107 201 05,
bullet 944 107 201 08
XZN Triple Square Set 24.99
XZN Set of 4 "Triple Square" Tools.
This set includes sizes:
6mm, 8mm, 10mm & 12mm bits
Drive size is 3/8"
A very handy set for the German car Technician. You get all four (4) tools with this purchase.

Triple square, also known as a XZN socket, is a type of screw drive. They are commonly found on German vehicles such as BMW, Mercedes, and Volkswagen etc... These screws/fasteners are used in some high torque applications such as cylinder head bolts and drive train components. Triple square bolts are common to early Porsche and Volkswagen (CV) constant velocity joints. Increasingly, triple square screws are found on other European and Asian makes of cars. Other names for this type of triple square screws and drivers are "Double Hex", "Double Allen", and "Aircraft Screws". Despite this, "Double Hex" and "Double Allen" are misnomers. The recess in these bolts is actually (as the name suggests) made of three squares, not two hexagons. The corners are 90 degrees, not 120 degrees. They are not double hexes, and an Allen key will not fit them properly.

These are XZN Triple Square Tools. XZN means Triple Square or 12 point. If your tool book calls for XZN or Triple Square or 12 Point, these are probably the tools you need. Satin Chrome with New S2 Alloy Steel. These are some of the strongest drivers you will find.
36mm Open End Thin Wrench 19.99
Long 36mm Thin Wrench
ON SALE
Female Torx Wrench Set 38.50
Female 5 Piece Set *
Torx Box Wrenches
Sizes included:
E6 X E8, E10 X E12, E14 X E16, E18 X E20, E22 X E24,
polished chrome.
Hazet Quality Tools 57.50
Adjustable Spark Plug Socket (13/16) 20.8mm.
Range is 137.5mm up to 197.5 overall.
Extra Long Pliers 17.95
"Extra Long" Valve Stem Seal Pliers
You will not see these every day, or find a better price on this tool anywhere! These are longer than the standard Valve Pliers. Tool is used for the proper extraction of hard to get at stem seals. The inside grooves on the tips of this Plier allows the firm grip of both O.E. and aftermarket seals Applicable: Overhead Cam engines.
Thin Head Flexible Ratchet 89.50
Ever see this one? It is a Super Tool....
A flexible "Thin Head" Reversible bit holding Ratchet.
(the reverse mechanism is on the flip side of photo not shown)
The head will flex backwards forwards more than a 90 degree (70 to 80)
The thickness of the head is 10mm
The overall length is 164mm ( 6 1/2 inch).
This tool is great for getting into a tight spot with a special bit,
during rare or difficult procedures (bits not included)
Call if you are looking for a special bit to go with the tool.
Disc Brake Piston Reset Tool 38.75
Disc Brake Piston Reset Tool / Brake Press Tool
Very STURDY tool for the safe resetting of disc brake pistons on vehicles with fixed caliper disc brakes / for putting the pistons back into the housing.

TOOL IS APPROX 2 5/8" HEIGHT PLATE TO PLATE (top to bottom)
each plate is about 6.5mm thick
depth of tool front to back (inside) is 2 3/4 inches (69.85mm)

TESTIMONIAL: 
When I attempted to replace the front brake pads on a 2001 Mercedes S430, I discovered that my old Piston Reset Tool (the one everyone has in their garage, sold everywhere under different brands for less than $10) just could not do the job. This is because the S430, like many other cars, has Dual Piston, Fixed Caliper brakes, which require a different Reset Tool (sometimes referred to as a Brake Pad Spreader). 

When I went to Pep Boys, my salesman there told me that fixed calipers are a problem, and he did not have the tool for the job. I went to an independent parts store, which had a tool that had been hanging on their wall since 1979 (it looked like a miniature scissors jack with a long screw), but it could not have been inserted where it needed to be. NAPA had a catalog with a picture of something with a pistol grip on it that looked like it may or may not have worked. The Mercedes dealer can order a tool (MB 000 589 52 43 00) for $160 that looks like it could be used 1,000 times before it would come close to breaking or wearing out, which would be overkill; besides, it is huge and would take up too much room in my tool cabinet.

Bottom line: I had to buy a tool, and nobody stocks one, so I had to order something from somebody. I found the item number MK BRK J at ZDMAK for a very low price, and could see from the picture that it should work, so I ordered it. I am glad I did ? it arrived on time, and it worked perfectly!

Procedure was simple: 
I took the cap off of the master cylinder under the hood, then jacked up the car and removed the wheels. The calipers remained bolted to the car throughout the procedure (of course, if I was replacing the rotors also, I think I would have had to remove the calipers). After removing the retaining pin and spring from behind the pads, I inserted the Reset Tool arms between the small exposed edges of the backing plates on the brake pads. Then I turned the handle on the tool and the arms pushed away from each other and started pushing the brake pads away from the rotor. Once there was more space I put the arms of the tool against the face of the pads themselves and pushed the pads (and pistons) all the way back. The tools job was done; I then slid the old pads out, slid the now ones in, reinstalled the spring and pins and I was done (after checking the fluid level and putting the cap back on the master cylinder).

I feel that I did receive a super tool which does the job perfectly and should last a DIY er a lifetime. 
It does not take up too much space in the tool box, 
and was also the least expensive option I found! 

Steve M
Pennsylvania
Panel Popper Set of 5 16.50
DOOR PANEL & UPHOLSTERY TOOLS Complete Panel "Popper" Tool Set
Super Tools for Auto Interior Work
This 5 Piece Set of plastic pry pullers is perfect for working on those expensive panels on car interiors. It will also help work loose plastic decorative inserts, door moldings and countless other pieces on todays modern and many vintage cars.
* You may have seen other sets like this, but they only come with 4 pieces... This set has 5 pieces with more features plus the quality of this set is better (stronger and more durable) than other being sold,
making this a much better deal.
This set comes in a Clam Shell Protective Container.
Valve Plier Set of 2 37.50
Set of 2 tools: Valve Plier (top) used for the proper extraction of stem seals. The inside grooves on the tips of this Plier allows the firm grip of both O.E. and aftermarket seals Applicable: Most Overhead Cam engines.
Plus: Shim Plier used for proper R&R of valve adjusting shims. Applicable: Overhead Cam engines with adjusting shims.
22mm Socket plus 7mm Allen Wrench 29.99
2 Piece set
22mm Special Tube Socket 4491A plus 7mm Allen Wrench Used for securing the Strut tower retaining nut of most European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench) (This socket can also be used for R&R of Oxygen Sensor.)
Plus a 7mm Allen Wrench. The Allen wrench is 7mm and is 7.5 inches Long.
Mini Nut Driver Set 26.95
8 Piece Set designed to aid the technician with work on hex nuts and bolts for Dasboards, Radios, ECU, Instrument panels, etc...This is a nice set for removal and replacement of small Hex (Allen) Fasteners. Quick Open End application and interchange. Adustable length for hard to reach areas. Comes in the plastic container. See images below. Tool in assembled position adusts from a minimum 5.5 inch to a maximum 9.0 inch overall. Hex sizes are: 3mm, 3.5, 4, 4.5, 5, 5.5 and 6mm See images below       Click for Larger Image and more information  
Top Dead Center Indicator 13.50
Top Dead Center Indicator 9710 Used for T.D.C. on any Gas engine. Simply unscrew a spark plug and twist the rubber hose part of this tool into the spark plug hole. As you rotate the engine with a turning bar, the piston forces air through the whistle part of this tool. Once the whistling stops the engine is at T.D.C.
Hose Clamp Plier RB003 35.00
Read what some TDI People say about this tool: The clamp works fine on the MAF clamps & ones a little larger also and it has a locking ratcheting action as you tighten DEFINITELY shop quality! These hose clamp pliers are simply fantastic. Other types of hand type hose clamp pliers and they have a tendency to slip off. These will not! This Hose Clamp Plier is a Must for TDI People. Features & Benefits: Double line, allows for extra reach, removal and locking of clamps into open position, allows for removal of plastic and/or metal self tightening hose clamps with diameters of 11/16" 2 1/2" (18mm 54mm), precision clamp on end of flexible cable allows for extended reach where other models cannot reach, Pliers can be locked, freeing up your hands and making your job easy. Hose Clamp Pliers NUMBER P RB003
17 x 17 Injection Wrench 59.50
Double Ended Flare Nut Box Wrench Size 17 x 17mm Overall Length 241mm (9.5 inch) For injection pipes on Volkswagen / Audi This tool will help you when you remove and install the fuel lines from the injection pump and the injectors themselves. For TDI: You will still need to torque the 17mm fittings down to spec, but this tool will make taking the fittings off a snap, as well as putting them back on. This is a Factory Tool Made in Germany
Torx Set 15.99
Torx Tamperproof Set with 1/4 Drive and 3/8 Drive sizes.
11 Pieces, sizes included: (3/8 drive) T40, T45, T50, T55 and T60.
(1/4 Drive) T10, T15, T20, T25, T27 and T30.
Mini Uni Drive Set 27.50
ST9009 23 in 1 Mini Uni Drive Kit Features & Benefits:
This ?Mini Uni Drive? kit was assembled to aid the technician with:
R&R of small fastening screws of dashboards, radios, ECU,
Instrument Panels, etc.
Quick Double ended application and interchange
Shaft length adjustment for hard to reach areas
Anti corrosion tips, treated with Mag./Phos
Rotating Head
All pieces are neatly stored in a form fit storage case
Maximum length of Assembled tool: 8.5 inches
Minimum Length of Assembled tool: 5.0 inches
11 Double ended Bits
1 Quick Chuck Handle
T5 x T6
T7 x T8
T9 x T10
T15 x T20
PH00 x FL2.0mm
PH0 x FL3.0mm
PH1 x FL4.0mm
HEX1.5mm x 2.0mm
HEX2.5mm x 3.0mm
HEX1/8? x5/32
HEX5/64? x 3/32
Super Hex Set 17.99
Super Set Metric and SAE Hex Sockets
1/2 Drive 6 Piece Set
Sizes: 12mm, 14mm, 17mm plus 3/8, 1/2, and 9/16 inch
Hex Sockets in popular sizes.
Sockets on a rail Hex (Allen) Sockets
Great for working on German Cars.
Super Deal
Hazet Oil Service Tool 38.00
Porsche 911 Tool.
Hazet Oil Filter Wrench size 92mm.
With square drive nominal size 12.5 = 1/2 inch.
outside hexagon 27 mm.
15 point (inside flats or flutes)
For 911 and several other vehicles such as Saab 900, 9000 and 99 etc...
High Quality Tool Made in Germany.
Hex Socket 19mm 19.85
This is a 19mm Hex Socket 1/2 Drive.
World Famous Hazet Sockets Made in Germany!
Hazet Deep Offset 8 Pc Metric Set 169.50
This is an eight piece Deep Offset Wrench set Double Box wrenches with 12 points.Sizes: 6x7mm, 8x9, 10x11, 12x13, 14x15, 16x17, 18x19 and 21x22mm.
Super High Quality Tools Made in Germany by Hazet!<
Hazet Quality Tools 187.50
Piston Ring Compressor chrome plated, bent lever (width 32 mm), releasable strap
Long Pattern (Deep) Socket 30mm 37.50
1/2 Drive Long Pattern Socket 30mm.
Overall Length is 85mm.
World Class Hazet Tools Made in Germany!
Universal Valve Spring Compressor 58.50
Universal Valve Spring Compressor
This set is used to remove and install the valve spring with the cylinder head still on the engine and in the car, or with the cylinder head removed. The multi point adjustable base of this tool bolts securely to the head while the adjustable lever mechanism pivots from the bar thus compressing the spring. Quick removal and installation of the spring retaining keepers is then easily accomplished through the large openings on both sides of the compression tube. This set comes complete with an easy grip handle and a storage tray.&nbsp;
There are numerous variations in engine head designs
To set up the compressor the leg sets need to be installed on each end of the cylinder head with the valve cover bolts on to an area along the cylinder head that the legs can fit into. By bolting the legs to the cylinder head the round bar can be inserted through the legs to give a fulcrum point for the compressor arm. When bolting the legs to the head shims (washers) may be needed to give the legs clearance above any portions of the head. such as gasket alignment pins or cam towers. The compressor legs can also be bolted to the cam towers if necessary. Once the leg sets have been been firmly attatched and the round bar is inserted through the leg set holes, the compressor arm and bucket can be assembled using the clevis pin. Alignment of the center line of bucket to the center line of the valve spring is crucial! There are numerous adjustment holes in the compressor legs arm and bucket to allow alignment of the bucket to the valve spring.
The compressor arm has two detents that can give the arm the ability to compress the valve spring by either pushing down or pulling up on the handle depending on which detent is used and where the bucket is attached to the compressor arm. When alignment of bucket and valve spring is accomplished, the valve spring can be depressed and service to the valve components can proceed.
Service kit for OHV &amp; OHC gas or diesel engines on many VW Audi, Nissan, Toyota, Chrysler, Honda, Mazda, Mitsubishi, Porsche and Volvo.
Flexible Shaft 1/4 Driver 9.99
1/4 Inch Flexible Driver
Sizes on this tool is 1/4 inch Flex Drivers work well on many applications. This is a very popular tool. Rubber coated flexible shaft
Flexible 3 Piece Driver Set 22.50
3 Piece Flex Hex Nut Driver Set.
Flexible Shaft Nut Drivers are Great for the German car mechanic, great for working on hose clamps, hex headed screws and nut screws.
Sizes included in this set are 6mm, 7mm and 8mm.
You will get all three tools with this purchase.
Excellent for the Professional or Shadetree Technician!
M8, M10 and M12 Set 3 XZN 24.99
Super Set!
Three Headbolt Tools Triple Square 12 Point (XZN) Sockets M8, M10 and M12 Sturdy 3/8 Drive Tools used for a wide variety of applications including headbolts. Excellent for working on German and Asian vehicles.
Each tool is 4 1/2 inches long overall and the shaft is 3 inches long! PLEASE NOTE: These are NOT Torx tools, they are called XZN The German tool books refer to the 12 point style as XZN. This is a very popular set.
944 Tool Set 60.50
Set of two tools for 944
Flywheel Lock needed to stop the motor from rotating during removal and replacement of crankshaft bolt or motor. Applicable: Porsche 944.

Alignment Pin ZDMAK number P218 Same as Porsche Tool 9215.
Alignment Pin crucial in order to properly reinstall the oil filter/water intercooler housing.
Not using this Alignment Pin may cause misalignment during this procedure, which may lead to the oil pressure relief valve sticking and ultimately engine damage.
Applicable: Porsche model 944 from 1983 to 1986.
Impact Quality S2 Bit Set 10.50
Impact Quality S2 Bit Set, 8pc Bits 5/16" Hex bodies, 1.25"L, P1 P4 Phillips & 1/4", 5/16", 3/8", 1/2" Flat Bits, Plastic Holder
Triple Square Sockets Set of 2 24.50
Set of 2 Triple Square XZN (12 Point) Sockets.
One of each size M10 (10mm) and M12 (12mm).
Drive size 1/2 inch. Overall length 4 inches.
9 Piece Disconnect Set 9.99
9 Piece Fuel, A/C and Transmission line disconnect set With SPRING LOCK and new improved SLIP ON COUPLING DESIGN. Applicable: 1981 and newer Ford cars and pick ups, Chrysler and G.M MODELS Includes: (3) 3/8, (2) 5/16", (2) 1/2 (1) 5/8 and (1) 3/4 inch sizes.
Hex Socket 14mm 22.50
This is a 14mm Hex Socket 1/2 Drive.
World Famous Hazet Sockets Made in Germany!
Socket for 911 0.00
Gearbox Socket for 911
Seal Remover Puller 11.50
TOOL VW681 Seal Remover Puller For grease seals and oil seals. The two tips will fit many applications.
SUPER TERMINAL TOOL 37.50
Introducing the SUPER Terminal Tool The "Swiss Army Knife" of wire terminal extractors. This internationally patented design offers the technician a handy "all in one" extractor kit that folds up and slides together into its own unique and compact storage housing. This kit is equipped with (12) factory correct extractor press bits. These press bits release DC wiring terminals from its harness that connect to ECUs, sensors, etc., found on most late model vehicles.
Holder for 911 0
Guage Holder for measuring intermediate shaft end play.
Locking Device 0
vw521/4 Locking Sleeve for measuring backlash to be used in conjunction with guage holder vw387.
Applicable most Porsche models. Check your manual for details.
Super Long Plier 13.99
Super Long Pattern Sparkplug Connecter Plier
Heavy Duty
Overall length 11 inches (279mm)
14mm plus 10mm Hex Set 22.50
BMW SPECIAL 2 Pc Hex Set 14mm Plus 10mm
1/2 drive sockets.
Metric Feeler Guage 8.99
25 Straight Blade
Feeler Guage Set
Thickness In millimeters
The blades in this guage set are metric sizes. 0.04 thru 1.00mm
Excellent for the professional or shadetree mechanic.
Cam Fixture 996 and Boxster 235.00
Cam Securing Fixture designed to secure the intake and exhaust cams during base timing. 996 up to year 01 and boxster up to 04.
Oil Seal Arbor 108.00
Oil Seal Arbor Pulley Side of crankshaft Porsche 996 and Boxster
Oil Seal Arbor Flywheel Side 180.00
Oil Seal Arbor FLYWHEEL SIDE Porsche 996 and Boxster
Oil Seal Remover 100.00
Barbed Splined Seal Remover for Gearbox main oil seal 996 and Boxster.
Engine Support 996 179.00
Engine Support for R & R of Trans Axle and Gearbox work 996
Ribe Key Set 7 Piece 27.50
Ribe Key Set Works on late model Porsche, Volkswagen Audi, Lancer, Fiat, and Lancia vehicles. Ribe style bolts are used on cylinder heads, headlights, and transmission fill plugs.
Please note: These are not Torx tools and they are not XZN they are Ribe!
Set includes seven keys: M4, M5, M6, M7, M8, M9, and M10
If you are unsure of the style you need, please call or email.
Ribe Bit Set 21.50
Ribe Bit Set 3 Pc
6mm, 8mm & 10mm bits in 3/8" Sq.Dr. holders.
Especially for Porsche
Ribe style sockets work on late model Porsche, Volkswagen Audi, Lancer, Fiat, and Lancia vehicles. Ribe style bolts are used on a wide variety of applications and a wide variety of vehicles example:
Brake Calipers (6m & 8m) 911 Camshaft 944(6m)
cylinder heads, headlights, and transmission fill plug etc . . Please note: These are "not" Torx tools and they are not XZN they are Ribe! Set includes seven keys: M4, M5, M6, M7, M8, M9, and M10 (Some earlier calipers are held together with RIBE bolts. These bolts have a 6 point head that looks like a TORX bolt head but is not the same. The RIBE style has a slightly different pattern and will make putting them back on and torqueing them properly with a TORX socket more difficult and may result in you mangling the bolt head. If you want to keep the RIBE bolts in good shape you will need to use the correct tool which can be difficult to find).
Tri Square Drain Plug XZN 49.50
This is a Special Tamperproof Transmission Drain Plug Socket. Triple Square ( 12 Point XZN 16) Same as old Volkswagen Tool 3357. (Number 3357 is still found in many/most manuals for this job)
Applicable Porsche Boxster and Audi A4 A6 and Passat. This is an excellent high quality tool Made in Germany.
* Plug not included, picture is for reference only.
Radio Removal Set 21.50
This is the best price set on the market...Bar None! The competition does NOT offer this COVERAGE for the price they charge.
This is a Master Set and it is used with BMW, Mercedes, Volkswagen Audi, Porsche and DIN.
FULL COVERAGE on Volkswagen Audi.
What makes this set better is a total of 8 keys for VW Audi and two for BMW plus the grips on the keys are coated for easy use.
You will notice a total of 3 different sets for Volkswagen Audi, two different tools for BMW and a set for newer Mercedes that will also work with older Mercedes and also works with some Porsche. (Same as Porsche ref: 000 721 957 01)
Here is what you get....Details below...

A. VW Tools (4) Number T10057 Audi A4, A6, A8 and New Beetle
For Concert, Symphony I and Symphony II stereos. Also for Nav units in Trunk and for CD changers in Glove box.
If you have 4 slots VW AUDI this is the set (T10057) you need. This 4 piece set is extremely popular.
The 2 piece VW set is Number VW 3316 New Body Style Passat Jetta Golf . Virtually full coverage for Volkswagen Audi when you buy this set.

B. BMW Tools are one Pentagon shaped tool with a 3 5/8 inches overall length. Applicable: Most BMWs. This Five sided driver is used to release anti theft radio mounts. You will also get the special rare very small allen tool for BMW (upper left) For newer BMW E38 & E39 7 SERIES

C. Mercedes Tools covers almost all newer and older vehicles, especially 1992 and newer 129, 140, 163, 202 & 210, Range Rover with Becker Nav System.
The MB Tools also work on Porsche. Appl: Turbo GT, GT2, GT3, Boxster, Cayenne 911, 996 , 987, Carrera etc.
Same as Porsche ref: 000 721 957 01 D. "U" Hooks for DIN Ford
P220 Wrist Pin Tool 19.00
Wrist Pin Installer Applicable: Porsche 914 4 912E
Torque Angle Guage 13.99
Torque Angle Guage 1/2 inch Drive
Measures angle of rotation after pre torque load in torque angle applications.
360 degree scale clearly marked in 2 degree increments and intervals of 10 &amp; 30.
Easily zero the gauge by turning housing for next application. For the fasteners used on some vehicles, automotive manufacturers are specifying both torque and angle settings. With the gauge, the professional mechanic can meet the demands of the new specifications: to turn the fastener a specified number of degrees after initial torque is set. The gauge takes the guesswork out of tightening by indicating the number of degrees that the fastener is turned on a large, easy to read scale.
360 angle scale clearly marked in 2 increments, and in intervals of 10 &amp; 30
Indicator etched on clear plastic plate protects angle scale from dirt and grease
Adjustable arm keeps angle scale stationary. Arm has two lengths for additional flexibility in placement against components.
Easy disassembly for cleaning just unclip retaining ring.
Torque + Angle Specification:
Example: If a torque + angle specification is given as 50 Nm + 70, the fastener is first torque to a threshold of 50Nm; then it is turned 70. If the specification reads 50Nm + 70, torque is first set to the 50Nm threshold. Each bolt in the sequence is then turned 70 once. When the entire sequence has been tightened to 70, each bolt in the sequence is given a second 70 turn.
The Torque + Angle Method:
Select a torque wrench, which indicates the threshold value at midrange. Torque the fastener to the manufacturers threshold torque.
Attach the proper size socket to the gauge. Attach the socket with gauge to the fastener.
Turn the arm clockwise until it meets a firm point of resistance.
Zero the gauge by turning the housing until it lines up with the 0 setting.
Connect a breaker bar, ratchet or other square drive to the gauge.
Holding the arm assembly firmly, turn the fastener the number of degrees specified. The proper clamp load has now been set and no further torquing is needed.
Torque Angle Meter 42.50
Torque Angle Meter For all torque to yield fastener applications. Commonly used for tightening head bolts and other bolts where torque angle is required. Use with 1/2" drive.
Snap Ring Plier Set 13.50
5 Piece
Snap Ring Plier Set
Plier handle and (4) tip assemblies: (2) straight, (1) 45 and (1) 90 (1) spring retainer assembly Vinyl grip handles For Internal or External snap rings
7 Way Crimping Tool 8.99
7 WAY CRIMPING TOOL Wire cutter, terminal crimper & wire stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on end of tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire Works with 10 22 gauge solderless terminals.
Ratcheting Terminal Crimper Kit 99.99
Ratcheting Terminal Crimper Kit
? Versatile kit includes 5 dies
For virtually all uses. ? Die sets quickly interchange for a wide range of applications. ? Crimping tool has a steel frame with contoured grips. ? Supplied in a durable, plastic, molded storage case with carrying handle. Applications: ? Insulated terminals 22 10 AWG ? Non insulated open barrel connectors 22 10 AWG ? Fully insulated quick disconnect terminals with thinner wire barrels 22 10 AWG ? Non insulated terminals 22 8 AWG ? For miniature insulated rings, spade and butt splices 16 26 AWG
Metric Ball Hex Tool Set 14.95
Very Cool Metric Ball Hex Set 11 Pc
1.5mm thru 8mm ball hex bits, VI10 magnetic driver & 1/4" hex X 1/4" Sq.Dr. chrome bit holder in blue plastic box.
Two Torx Sets 26.99
Two Torx Sets Special Deal
MALE & FEMALE SETS
Male Tamperproof Torx (6 POINT)
Set with 1/4 Drive and 3/8 Drive sizes.
11 Pieces, sizes included: (3/8 drive) T40, T45, T50, T55 and T60.
(1/4 Drive) T10, T15, T20, T25, T27 and T30. Plus you will get the ten piece Female Set
Description: 10 Piece Torx Female Socket Set
3/8 Drive and 1/4 Drive assorted sockets on a rail.
The (smaller) 1/4 Drive Sizes are: E4, E5, E6, E7, E8.
The (larger) 3/8 Drive Sizes are: E10, E12, E14, E16, E18.
7 Pc Adapter Set 14.99
Includes: 1/4", 3/8", and 1/2" U Joint style adapters.
Plus adapters 3/8" to 1/4", 1/4" to 3/8" , 1/2" to 3/8", and 3/8" to 1/2" drive adapters.
100 pc Security Bit Set 16.99
100 Piece Security Bits Set: Contains many of the most common tamperproof type security bit sizes,
including torx bits, spanner bits, hex bits, tri wing bits, and special XZN bits. Includes items below...

1 wing nut driver.

1 magnetic bit holder.

1 socket bit holder.

1 1/4" sq. x 1/4" hex x 1" extension.

1 1/4" sq. x 1/4" hex x 2" extension.

3 clutch bits ( 1, 2 & 3)

3 torq bits ( 6, 8 & 10)

3 XZN (spline) bits (M5, M6 & M8)

4 tri wing bits ( 1, 2, 3 & 4)

4 square recess bits ( 0, 1, 2 & 3)

4 spanner bits ( 4, 6, 8 & 10)

6 metric hex tamper proof bits (2, 2.5, 3, 4, 5 & 6)

6 SAE hex tamper proof bits (5/64, 3/32, 7/64, 1/8, 9/64 & 5/32)

8 phillips bits (0, 1, 2{5} & 3)

8 pozi drive bits (0, 1, 2{5} & 3)

9 slotted bits (3, 4, 4.5, 5, 5.5, 6, 6.5, 7 & 8)

9 metric hex bits (1.5, 2, 2.5, 3, 4, 5, 5.5, 6 & 8mm)

9 torx bits (T 8, 10, 15, 20, 25, 27, 30, 35 & 40)

9 torx tamper proof bits (T 8, 10, 15, 20, 25, 27, 30, 35 & 40)

10 SAE hex bits (1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32 & 1/4)
For the German Car mechanic this set is worth the price because of the Torx and XZN (spline) bits (XZN sizes 5mm, 6mm and 8mm) these three small XZN bits are very hard to find in this short pattern.
You can see these 3 bits on the right hand side second row from the bottom.

Comes complete as shown with (indexed) storage / carry case.

Bonus Triple Square Set 5 62.50
12 Point Headbolt Tools Plus Drain Plug Socket. (Anyone looking knows how hard it is to find a good price on XZN Tools here you have the extremely popular size 10 and more...)
The Headbolt Set of 4 Includes: 6mm, 8mm, 10mm & 12mm
with 3/8 Drive holders on a rail.
Plus you get
Drain Plug Socket (Upper Left)
Special Large size M16
(Notice the Tamperproof Center on the M16)
Drain Plug Socket Triple Square (12 Point = XZN )
For Porsche Boxster and Audi A4, A6 and Passat
A very handy set for the VW, Audi, Porsche and German car mechanic.

Note: The 4 pieces (Right) are regular XZN and the drainplug tool is tamperproof.
You will get all five pieces with this purchase.
Pick and Finish Hammer 12.99
Pick and Finish Hammer High quality auto body Tool For knocking down high spots and finishing. High carbon drop forged steel head, hardened and tempered. Genuine American hickory handle.
Drill Press Vise 16.99
SMALL BENCH TOP VISE This is a 3 inch drill press Vise that fits the "mini" or "benchtop" drill presses. Vise bolts right to the work table, and allows you to secure whatever you are drilling. This item is a must have item for anyone with a drill press. You will like the quality of this vise.
Dimensions:
5 1/2" Width
2" Height
6 1/4" Length.
Jaw opening: 3".
Mounting holes is 4 1/2" apart.
Etched Jaws to prevent slipping. Slotted mounting holes and pivoting arm for easy turning and adjusting.
Base (mounting) Size 5 1/4 x 5 1/4
Multi Function Oil Wrench 29.99
Double Sided Multi Oil Wrench One Wrench contains 8 socket sizes from 12mm to 19mm.
Specially Designed to fit all common oil drain plugs
Innovative swivel design allows a technician to access and remove many common Oil Pan Drain Plugs. Swivel head allows full range of motion to access the most difficult oil plugs without creating a mess. Overall length of 10" allows for easy handling and access.
Deep Offset Wrench Set 110.00
Deep Offset Box Wrench Set
8 Piece set sizes included:
6 x 7mm
8 x 9mm
10 x 11mm
12 x 13mm
14 x 15mm
16 x 17mm
18 x 19mm
20 x 22mm
12 point ring spanners. Satin chrome, made of high performance forged steel.
Polished head and ring. High Quality Tool Set Made in Germany!
Set 3 Porsche Clutch Tools 11.99
Porsche Clutch Alignment Tools Set 3
Covers a BIG variety of Porsche Applications. The clutch tools in this kit are extremely durable long lasting and inexpensive. These tools can be used over and over again.
A must for clutch repair shop, clutch specialist, transmission repair shops, automotive stores, school shop classes, clutch resellers,
foreign and domestic repair shops. You get all three tools with this purchase. Coverage below. Porsche 356, 356A, 356B &amp; 356C 4 1.1 1950 55&nbsp;
Porsche 356, 356A, 356B &amp; 356C 4 1.3 1950 57&nbsp;
Porsche 356, 356A, 356B &amp; 356C 4 1.5 1952 59&nbsp;
Porsche 356, 356A, 356B &amp; 356C 4 1.6 1960 65&nbsp;
Porsche 911 6 3.0 1972 77&nbsp;
Porsche 911 6 3.2 1986 90 1 1/32" Hub. Dia. W/23 Spl.&nbsp;
Porsche 911 6 3.3 1986 94&nbsp;
Porsche 911 6 3.6 1989 97&nbsp;
Porsche 911 6 2.0 1965 69&nbsp;
Porsche 911 6 2.2 1969 71&nbsp;
Porsche 911 6 2.4 1971 73&nbsp;
Porsche 911 6 2.7 1971 77 13/16" Hub Dia. W/ 24 Spl.&nbsp;
Porsche 911 6 3.0 1975 77 13/16" Hub Dia. W/ 24 Spl.&nbsp;
Porsche 912 4 1.6 1965 69&nbsp;
Porsche 912 4 2.0 1975 76&nbsp;
Porsche 914 4 1.7 1970 74&nbsp;
Porsche 914 4 1.8 1974 75&nbsp;
Porsche 914 4 2.0 1973 76&nbsp;
Porsche 914 6 2.0 1970 72&nbsp;
Porsche 923 4 2.0 1975 76&nbsp;
Porsche 924 4 2.0 1978 85 1 1/32" Hub. Dia. W/23 Spl.&nbsp;
Porsche 924 4 2.5 1985 88&nbsp;
Porsche 924 4 2.0 1976 85 13/16" Hub Dia. W/ 24 Spl.&nbsp;
Porsche 928 8 4.5 1978 83&nbsp;
Porsche 928 8 4.7 1983 86&nbsp;
Porsche 928 8 5.0 1983 91&nbsp;
Porsche 928 8 5.4 1993 95&nbsp;
Porsche 928S 8 5.0 1987 91&nbsp;
Porsche 930 6 3.0 1974 77&nbsp;
Porsche 930 6 3.3 1977 91&nbsp;
Porsche 944 4 2.5 1981 90&nbsp;
Porsche 944 4 2.7 1988 90&nbsp;
Porsche 944 4 3.0 1988 91&nbsp;
Porsche 968 6 3.0 1992 96


These Clutch Alignment Tools are simple to use, and made to last.
Injection molded out of high quality polypropylene making it free from abrasion.
Beware of cheap immitations that will wear or break easily or dont fit the application properly. &nbsp;
V159 Pin Wrench 26.50
This is the Best Quality V159 you will find anywhere.
This is the pin wrench needed to adjust the timing belt tensioner pulleys on VW/Audi 4 cylinder gas and diesel 1.5, 1.6, 1.7, 1.8, 1.9 and 2.0 liter engines from approximately 1979 to 1997 and later, or earlier engines which have had the later style timing belt tensioner pulley installed. The pins on this tool engage the offset center hub of the timing belt tensioner pulley, allowing possibly a 15mm box end wrench to be placed on the pulley lock nut, and then rotatation the offset center of the pulley upward in order to achieve proper timing belt tension. Remember, these pulleys adjust upward, not downward. Correct tension on a gasoline engines timing belt is achieved when the timing belt can just be twisted 1/4 turn (90 degrees) with moderate pressure using thumb and index finger. Tension is checked midway between the cam sprocket and intermediate shaft. Tension that is less than this will cause timing belt chatter. Tension greater than this will cause the timing belt to howl once it gets hot and could lead to premature timing belt failure. Correct tension for the diesel engines is checked and adjusted the same way, with the exception that the belt tension is checked midway between the cam sprocket and the injection pump sprocket and should only twist 1/8 of a turn (45 degrees) using the finger/thumb twist method previously described. Additionally, when doing a timing belt on the diesel engines, the cam locking tool is required, and the cam sprocket must be loose, allowing the cam to be locked at TDC, and then the crank, injection pump, and cam sprocket are then rotated independently from the cam in order to achieve TDC for both the crank and injection pump. Some manuals call this tool number 2587 and the newer manuals may have it listed as number V159 (either number is correct).
SUPER HIGH QUALITY TOOL MADE IN GERMANY BY HAZET!
Basic timing tool info Video Click Here People who bought this item also search for the following items
(popular searches include the following tools:
2064
2065
2065a
2066
3032
2587
3391
2066
T10020
3387
3359
3418

*If you do not see the tool number you are looking for please call or email.
Fuel Clamp Set 4 24.50
4 Piece Fuel Line Clamp set.
Clamp off Fuel, Vacuum, Transmission, Brake, Heater lines Etc.....
Sizes included:&nbsp;
Extra Large 1 3/4 inch
Large 1 inch
Medium 1/2 inch
Standard size 3/8&nbsp;

The big piece (EXTRA LARGE) is a whopper 1 3/4 inch,
and by itself would be worth the price of this set.
It is a very large tool measuring 4 1/2 x 4 inch&nbsp;
The most popular size however is the STANDARD size (3/8)
A nice deal for a set of 4 clamps.
Tie Rod End Ball Joint Tool 24.99
Tie Rod End / Ball Joint Lifter. This labor saving tool quickly separates tie rod ends and ball joints from suspension components. Eliminates broken grease reservoirs. No need for excessive hammering. Powerful lever action breaks loose even the most stubborn joints. Works on virtually all tie rod ends and compact car ball joints. Heavy duty, all metal construction. For use with hand tools only. Heat treated drop forged steel body &amp; bolt for long rough usage. Spread ball joints easily where space prevents use of direct action method. Jaw opening: 11/16" (almost 3/4) SIDE TO SIDE. (Spread: UP and DOWN equals 1 7/8"). Click Here to see a Drawing on this Tool &nbsp;
Indicator Points Set 16.50
Indicator Points Set Complete Set comes as shown Includes 22 assorted round, pointed, flat, and angled points. 4 48 Threads.
Starter Wrench Set 5 Pc 29.99
Metric Obstruction Wrench Set 5 Piece
Size 8 x 10mm
11 x 13mm
14 x 15mm
17 x 19mm
21 x 22mm
12 Point Tools used in a wide variety of automotive repair applications. Specially designed for starter bolts and used mainly for starter motors and inlet and exhaust manifolds.
Extra Long Boot Plier 29.99
Extra Long Spark Plug Wire Pliers Rare and hard to find at this price. Used to remove the newer high voltage type wires Wide grip section and special extra long pattern makes it easy to remove wires without separating crimps. Applicable: 102, 103, 104, 110, 115, 116, 117, 119, 120 Similar to Mercedes Tool Number 104 0037 except this tool is much longer.
Interior Tool 45.50
Original pry puller! Strong tool for working on panels on vehicle interiors. It will also help work loose plastic decorative inserts, door moldings and other pieces on modern and many vintage cars.
MADE IN GERMANY
M4 XZN Triple Square Stubby Male 7.00
Size M4 Triple Square Stubby 3/8 Drive. Rare and hard to find single short pattern 12 point socket.
XZN (Triple Square) Super Stubby Socket This tool is 1 1/2" long.
Sturdy compact One Piece design. Satin Chrome with black impact tips.
S2 Alloy Steel. Fully Heat Treated. Picture is for reference only. See other sizes Click Here to go to the SOCKET section.
Triple Square Socket for Transmission 33.00
Drain Plug Socket: This is a Special Tamperproof * Transmission Drain Plug Socket. Triple Square ( 12 Point XZN ) Same as Volkswagen Tool 3357. For Porsche Boxster and Audi A4 A6 and Passat. This is an excellent "Stronger One Piece" design.
10 Piece Metric Hex Set 29.99
10 Piece 3/8? Drive Metric Hex Bit Socket Set
Heat treated Chrome Vanadium steel construction.
Sizes are: 2, 3, 4, 5, 5.5, 6, 7, 8, 9 & 10mm
Set comes on a rail as shown.
Excellent for the German car lover!
Set 2 Alternator Tools 23.50
Combination Socket Set of 2 consisting of the 19mm Multi Spline (short socket) and XZN (longer 12 point socket) size M10 for mounting and dismounting the alternator pulley. Volkswagen Audi Mercedes Porsche etc...For mounting the V belt pulley (slip clutch pulley) at the alternator (some older manuals call it a generator), especially for T.D.I. VW Golf III, Vento, Passat and AUDI A 3.
The short serrated socket (3400) is size 19mm outside diameter and Length is 30mm.
The larger tool is M10 XZN triple square and is 3/8 drive x 4 inch length. See repair Group 27 (Porsche Bulletins) Boxster Alternators with free wheeling Pulleys.
Also: 1990 to 1994 Porsche C2 and C4 and all Porsche 993s use a (M10) 10mm 12 point socket tool to hold the alternator shaft when replacing the belts the area between the alternator and car body is very limited a 10mm 12 point spanner style wrench works well for this job.
Belt Tension Tool 59.99
Timing belt tension checking tool for use on timing belts in vehicles where the manufacturer specifies that the timing belt tension be set according to newton meters, at a specific location on the belts span between pulleys. Applications include Porsche 928, 924 & 944, Audi V 6 and V 8 engines, certain Volkswagen engines, and others as noted in your service manual.
This tool measures the tension that it takes to depress the timing belt, allowing you to adjust the position of the timing belt tensioner pulley to precisely the right spot. Use of this tool speeds up the timing belt installation process because it eliminates the guess work in properly adjusting the timing belt, keeping you from having a belt that chatters from being too loose, or howls once hot, from being too tight.Click on this LINK below to see more about the BELT tool,
also if you are serious about purchasing the tool, send an email and we can forward more documents (info) on this item.
Brake Tool Gun Only 55.00
Pneumatic Brake Caliper Piston Compressor SIR TOOLS
Features and Benefits:
Rotates Left or Right in order to Wind Back Pistons allowing serious time savings with less effort Straight shot, down the center continuous force. The pressing shaft of this air gun is acting on a force of 1:1 from the air compressor. Solid cast aluminum body is durable, light weight and anodized. All pieces are securely housed in a blow molded case. The Air Gun incorporates a single piston press shaft, which is a non impact type action. Magnetic pad attachment base securely holds press pads mates up to most competitors pads Air Gun equipped with an adaptor allowing the technician to use own pads. The Air Gun incorporates a single piston press shaft, which is a non impact type action. Finger controlled press speed. Magnetic pad attachment base securely holds press pads. All moving parts are made from high quality chrome alloy steel. The Pneumatic Press is equipped with a rubber guard where it seats inside the brake caliper, so as not to damage the tool or caliper components.

Gun comes as shown the Technician will need to supply his own pads.
This product is also available in a set complete with 16 pads. This item (number ST9020G) is for the Gun only.
Thin Wrench Set Metric 129.50
Thin Wrench Set Chrome Plated. Specially designed Service Wrenches: Each wrench is thinner than a regular wrench, used on thin nuts and for getting into spaces. All mechanics need thin wrenches occasionally to work on transmissions, gas tanks or changing a wheel on a creeper seat. This intermittent use does not justify the very high price charged by the competition; this is one of very few reasonably priced alternatives on the market. Made of high strength manganese alloy steel, these wrenches are heat treated and tempered to maximize strength. Not intended for high torque applications. Service wrenches are traditionally designed with trucks and hydraulics in mind. They are also very useful working on new cars and pick up trucks. Sizes included: 20, 21,22, 23, 24, 26, 27, 28, 29, 30, 32, 33, 34, 35, 36mm.
Tensioner Tool 22.50
FACTORY TOOL Tensioner Number T40009 Original Factory Tool Made in Germany. FOR TENSIONING OF TOOTH BELT WITH PROPER TIGHTENING TORQUE VW AUDI T40009 ideal for the timing belt tensioner on 924 as well. You can use this Tool with a torque wrench and get a more precise tensioning figure. Especially important when dealing with the belts on 924 Turbo 924 (76 85) with the 2.0L ) which is a big time interference engine and if the belt goes so do most of your valves.
32 x 36mm Open End Wrench 39.95
32 x 36mm Thin Pattern Metric Open End Wrench
High Quality Thin Pattern Wrench Made in Germany
Chrome Plated Polished Head Narrow Profile for Easier Access In tight Locations.
View the CHART to see more Wrench sizes Click Here
Satin Chromed Sure Grip Body Made from 31CRV3 High Performance Tool Steel Precision Formed For an Exact Fit
OEM Specified By BMW, Mercedes & Rolls Royce Guaranteed Quality Made In Germany
This wrench mees DIN 3110 / ISO10102 specifications.
Please note: If you choose a smaller size wrench the image is not to scale.
This picture is the 32 x 36mm Wrench.
If you need a different size, please look at the chart (click on the link) then come back and type the item number you prefer into our search field. Email or call with any questions.
JET REAMER SET 74.50
JET REAMER SET 16 piece Jet Reamer Set with a 0.33mm 2.0mm range. Applicable to Porsche, VW and Audi models with carburetors. MADE IN GERMANY Be sure to CLICK HERE for More Special Tools
11 Piece Set Interior Tools 43.50
11 Piece Set Interior Tools. Specifically designed set including tools with extra slim profiles for the finer jobs. Special contours and unique features for effective and safe removal of fine or delicate bezels and fascia. The Pry Tools will not scratch or mar fascia. It tackles finer jobs that the average tools are too big for. These tools are made from impact resistant high quality nylon. Each Pry Tool within this six piece Fine Kit (on the right side of the image is specially designed with an extra slim profile and unique shape for the delicate task of removing small or fine fascia trim and bezels of; dashboards, air vents, door panels, door locks, electronic seat controls, seat levers, center counsels, gear shifter, etc....Super Tools for Auto Interior Work! This 11 Piece Set of plastic pry pullers is perfect for working on those expensive panels on car interiors. It will also help work loosen plastic decorative inserts, door moldings and countless other pieces on todays modern and many vintage cars. This set has more features plus quality of this set is great. (stronger and more durable) than other being sold, making this a much better deal...THERE IS A HIGH DEMAND for these interior tools.
3/16 Tubing Bender 36.00
3/16 TUBING BENDER UNIQUE HEAD DESIGN ALLOWS FOR SHARPER BENDS WITHOUT COLLAPSING THE TUBING OR LEAVING A DEEP MARK ON THE SURFACE. WHEN CLOSED, THE TWO HANDLES ARE MORE THAN 3 1/4" APART AND ALLOW ENOUGH LEVERAGE TO BEND TOUGH STEEL TUBING EASILY. YOU MAY HOLD TUBING FIRMLY TO ALIGN AND ADJUST.

Does not leave cutting marks at the beginning of a bend. You can slide a tube in the closed jaws of these pliers. This is one of the best 3/16" tubing bending pliers on the market. It works well, holds firmly, and is reasonably priced.
Valve Stem Seal Plier and Kit 59.99
Valve Stem Seal Remover/Installer Kit
Works on both valves still seated or removed. Precision machined seal driving adapters guide the seal for proper setting. Set contains: Valve stem seal plier. Drive handle 6? (150mm) long.
2 Deep seal driving sockets for seals O.D. 10.8 14.8mm
7 Seal driving adapters fit seals 5mm, 5.5mm, 6mm, 6.6mm, 7mm, 8mm, & 3/8?. Comes in the blow molded plastic carrying case.
Set 5 Point and 6 Point 59.95
Super Set including 5 Point and 6 Point Tools. You get full coverage with this Extra Long Security Torx Driver Set
Features 12" long blades with TamperProof Torx on one end and 5 Point security tips on the opposite end.
Double drive screwdriver handle, bits can be inserted as a standard screwdriver, or as a T handle.
S2 steel, the strongest hardest drivers available! Heat treated to 60 62 RC
The blades are satin chrome plated with a black tip on the 5 point end.
New extra long security driver set, includes 12" long interchangeable blades with T10 thru T40 Tamper Proof Torx on one end and 5 Point security Drivers on the opposite end. The Blades can be put in the 2 Way screwdriver handle as a screwdriver or use the "T" handle. The set also includes a special bit holder so these blades can be used with your favorite 1/4 drive ratchet handle. Comes with a plastic storage case.
XZN Set Long and Short Bits 19.99
11 Piece Tool Set with Metal carrying case
All tools are STYLE XZN
You will get five LONG
and
five VERY SHORT tools

Long and short are Sizes M5, M6, M8, M10 and M12

(THE M5 IS VERY HARD TO FIND
AND THE SIZES 8 , 10 and 12 are very popular sizes with the European auto techs.

XZN = means 12 POINT
Metric Bits
TRIPLE SQUARE

Pictures are for reference.
Each LONG bit is 3 inches Long.
Each SHORT bit is 1.2 inches long
The short bits are hard to find in these sizes and are very handy in a tight spot.


Heat treated alloy steel.
Sturdy 3/8 inch hex drive shaft.
The adapter is a hefty 1/2 drive
(1/2 x 3/8 converts to 3/8 to hold each tool which has a 3/8 shaft on each).

Tools Applicable to BMW VW Audi Porsche Mercedes Etc...

You will be hard pressed to find a set with these sizes and lengths in a metal case for this price!
Two Step Ground Feeler Blades 11.95
22 BLADE THICKNESS GAUGE
GO NO GO 22 two step ground blades. Decimal and metric sizes.
.004"/.006", .005"/.007", .006"/.008", .007"/.009", .008"/.010", .009"/.011", .010"/.012", .011"/.013", .012"/.014", .013"/.016", .015"/.017", .016"/.018", .017"/.019", .018"/.020", .019"/.021", .020"/.022" .021"/.023", .022"/.024", .023"/.025", .024"/.026", and .025"/.027".
Lapping Compound 9.99
Valve Grinding & Lapping Compound Fine/Coarse
Two duplex containers include 4 oz (108 grams) each Coarse Compound for Roudhing and Fine Compund for Finishing. Ideal for seating valves, mating gears, lapping injectors and honing knives. Mix compound with oil to obtain desired consistency.
Set Valve Lappers 13.50
Set of 2 Valve Lappers Sturdy rubber suction cups Hardwood Handle.
To be used with lapping compound (not included) for hand lapping Valves
Sizes are 5/8 x 13/16 diameter cups for smaller valves,
1 1/8 x 1 3/8 inch for large.
Hex Set (3) 14, 17 & 19mm 23.50
Stubby Hex Socket Set (3) Repair Tools 14mm, 17mm, 19mm
Three Special Short Pattern Sockets
One of each 14, 17 and 19mm.
PLEASE READ: EACH TOOL IS 28mm LONG
VERY HARD TO FIND IN THIS LENGTH AND SIZE FOR THIS PRICE!
You get all three tools with this purchase.
Super Tools Excellent for the Professional or Shadetree Mechanic.
PLEASE EMAIL OR CALL IF YOU DO NOT SEE THE SIZES YOU NEED.
Long Reach Feeler Guage Set 19.99
25 BLADE EXTRA LONG FEELER GAUGE For long reach applications especially diesel. 12" blades .0015., .002, .003, .004, .005, .006, .007, .008, .009, .010, .011, .012, .013, .014, .015, .016, .017, .018, .019, .020, .021, .025, .027, .030, .040". Blades also marked with metric equivalent. Knurled nut allows blade removal.Be sure to CLICK HERE for More Ignition Tools
Tappet Feeler Gauge Set 17.99
Offset Valve Tappet Feeler Gauge Set
Speeds valve lash adjustment. Install the proper blades for intake and exhaust settings and avoid fumbling with multiple blade stacks. Comfortable plastic handles with knurled nuts to hold blades securely. Offset blades for easy insertion. Blades are marked in both inch and metric. Eleven sizes from .004" to .014" (0.102mm to 0.356mm) SIZES INCLUDED BELOW:
.004/.102MM
.005/.127MM
.006/.152MM
.007/.178MM
.008/.203MM
.009/.229MM
.010/.254MM
.011/.279MM
.012/.305MM
.013/.330MM
.014/.356MM
Factory Tool 3417 29.50
Oil service Wrench 74mm with 14 Points (inside flats flutes).
Number 3417 Original Factory Tool 74mm Made in Germany by Hazet! 14 Points (inside flats flutes).
THIS ITEM HAS BOTH DRIVE SIZES 3/8" (10mm)
AND OUTSIDE HEX SIZE = 27mm
Some applications include: Mercedes, Audi, VW Golf, and New body Jetta, TDI (Diesel) and the following gas vehicles; Passat, Golf and Jetta with 1.8 turbo and 2.0 litre, Rabbit, Dasher, Scirocco, and New Beetle. Mercedes M104, M110, M111, M119, M120 C, E etc...
Porsche 944 and 924. Some Toyota. Check your manuals for details and size needed. Measure filter diameter or canister diameter.
See chart below.
bullet Audi Coupe 81 87
bullet Audi Coupe Q 20v 90 91
bullet Audi Fox 73 79
bullet Audi 100 89 91
bullet Audi 100Q 89 91
bullet Audi 4000 4 Cyl 80 87
bullet Audi 4000 5 Cyl 80 81
bullet Audi 4000 Q 84 87
bullet Audi 5000 78 88
bullet Audi 5000 Q 87 88
bullet Audi 80 88 90
bullet Audi 90 88 90
bullet Audi 90 Q 20v 90 92
bullet BMW 325 85 88
bullet BMW 325e 84 88
bullet BMW 325es 86 87
bullet BMW 325i Sedan 87 91
bullet BMW 325i Cabriolet 87 93
bullet BMW 325is Coupe 87 91
bullet BMW 325ix 88 91
bullet BMW 525i 89 90
bullet BMW 528e 82 88
bullet Mercedes 190E 2.3 1985 1993
bullet Mercedes 190E 2.6 1987 1993
bullet Mercedes 260E 1987 1989
bullet Mercedes 300CE 1988 1989
bullet Mercedes 300E 2.6 1990 1992
bullet Mercedes 300E 1986 1992
bullet Mercedes 300E 4 Matic 1990 1993
bullet Mercedes 300SE 1988 1991
bullet Mercedes 300SEL 1988 1991
bullet Mercedes 300TE Wagon 1988 1992
bullet Mercedes 300TE 4 Matic Wagon 1990 1993
bullet Porsche 924 77 82
bullet Porsche 924 Turbo 80 82
bullet Porsche Cayenne S 03 04
bullet Porsche Cayenne Turbo 03 04
bullet Porsche 911/996 Carrera/2 98 04
bullet Porsche 911/996 Carrera/4 99 04
bullet Porsche 911/996 GT3 04 04
bullet Porsche 911 Twin Turbo 01 04
bullet Porsche Carrera GT 04 04
bullet Porsche Boxster 97 04
bullet Porsche 911 Turbo 1991 1994
bullet Porsche 924S 1986 1988
bullet Porsche 944 1983 1989
bullet Porsche 944S 1987 1988
bullet Porsche 944S2 1989 1991
bullet Porsche 944 Turbo 1986 1991
bullet Porsche 968 1992 1995
bullet Porsche 928 78 84
bullet Porsche 928 32 85 95V
bullet Porsche 911/993 Carrera/2 1995 1998
bullet Porsche 911/993 Carrera/4 1995 1998
bullet Porsche 911 Twin Turbo 1995 1999
bullet Volkswagen Dasher 74 81
bullet Volkswagen Fox 87 93
bullet Volkswagen Golf GL/GT 85 92
bullet Volkswagen Golf III GL 93 94
bullet Volkswagen Golf GTI 8/16V 85 92
bullet Volkswagen Golf III GTI 93 94
bullet Volkswagen Jetta 80 84
bullet Volkswagen Jetta GL 85 92
bullet Volkswagen Jetta(Canada) 93 99
bullet Volkswagen Jetta Carat 85 92
bullet Volkswagen Jetta III GL 93 94
bullet Volkswagen Jetta GLI 84 88
bullet Volkswagen Jetta GLI 16V
bullet Volkswagen Jetta III GLS
bullet Volkswagen Passat 16V 90 93
bullet Volkswagen Passat GL 95 97
bullet Volkswagen Quantum 4 Cyl 82 85
bullet Volkswagen Quantum 5 Cyl 83 88
bullet Volkswagen Rabbit 75 84
bullet Volkswagen Rabbit Convertible 79 87
bullet Volkswagen Rabbit Cabriolet 88 93
bullet Volkswagen Rabbit GTI 83 84
bullet Volkswagen Scirocco 75 88
bullet Volkswagen Scirocco 16V 86 88
bullet Volkswagen Van Water Cool 83 92
bullet Volkswagen Van Syncro 86 92 This tool can be used on the following filters
bullet Audi, VW: 070 115 561, 056 115 561G, 034 115 561A
bullet BMW: 11 42 1 266 773
bullet Mecedes: 102 184 01 01
bullet Porsche: 996 107 225 52, 993 207 201 02, 993 107 203 03, 928 107 201 05,
bullet 944 107 201 08
Flywheel Lock 27.50
215 Volkswagen Porsche Tool
Flywheel Lock used to secure the crankshaft from rotating during R&R of motor.
Used in conjunction with Engine Holding Fixture P201,
where Flywheel Lock bolts into a machined channel.
All Porsche and VW 6V or 12V, air cooled. Please note: This item is included in the complete kit also.
Lappers Plus Compound 22.50
Set Valve Lappers and Compound.
Sturdy rubber suction cups Hardwood Handle. (to be used with lapping compound) for hand lapping Valves
Sizes are 5/8 x 13/16 diameter cups for smaller valves, 1 1/8 x 1 3/8 inch for large

Plus Valve Grinding & Lapping Compound Fine/Coarse Two duplex containers include 4 oz (108 grams) each Coarse Compound for Roudhing and Fine Compund for Finishing. Ideal for seating valves, mating gears, lapping injectors and honing knives. Mix compound with oil to obtain desired consistency.
You will get both Lappers and the Compound with this purchase.
Professional Piston Groove Cleaner 19.50
Professional Piston Groove Cleaner DESCRIPTION: Heavy duty model removes carbon from ring grooves on pistons from 2 1/2" to 5" (65mm to 127mm). Special design controls depth of cut and blade alignment. Side flanges allow use on slotted pistons. Includes cutter wheel with the following sizes: 1/16 and 5/6
SEAL PULLER 24.95
LOW PROFILE SEAL PULLER
Low profile blade allows you to work in tight access areas, including seals on import vehicles. Blade is alloy steel and heat treated for strength. Handle is heavy duty for strength and leverage.
Be sure to click HERE for more Special ToolsMore Special Tools Page 2 click HEREMore Special Tools Page 3 click HEREMore Special Tools Page 4 click HEREMore Special Tools Page 5 click HERE More Special Tools Page 6 click HERE
Long and Short Feeler Guage Set 24.99
Look Extra Long plus MINI Feeler Guage Set
Includes: 25 BLADE EXTRA LONG FEELER GAUGE For long reach applications especially diesel. 12" blades .0015., .002, .003, .004, .005, .006, .007, .008, .009, .010, .011, .012, .013, .014, .015, .016, .017, .018, .019, .020, .021, .025, .027, .030, .040". Blades also marked with metric equivalent. Knurled nut allows blade removal.

Plus
MINIATURE FEELER 17 Blade Mini Feeler Gauge 17 straight blades (1 1/2" long x 1/4" wide) .010, .012, .013, .015, .016, .017, .018, .019, .020, .022, .024, .025, .026, .028, .030, .032, .035.

You get both tools with this purchase.
17 Blade Mini Feeler Guage 7.99
MINIATURE FEELER 17 Blade Mini Feeler Gauge 17 straight blades
1 1/2" long x 1/4" wide
.010, .012, .013, .015, .016, .017, .018, .019, .020, .022, .024, .025, .026, .028, .030, .032, .035"
Test Leads 5.50
Test Leads Two 36" (91cm) jumper leads of 16 gauge stranded wire in heavy insulation for all purpose applications. Alligator clips are hooded.
Be sure to click HERE for more Special ToolsMore Special Tools Page 2 click HEREMore Special Tools Page 3 click HEREMore Special Tools Page 4 click HEREMore Special Tools Page 5 click HERE More Special Tools Page 6 click HERE
MASTER FEELER GUAGE SET 58 34.99
This is a MASTER SET FEELER GUAGES
YOU GET ALL FOUR DIFFERENT ITEMS WITH THIS PURCHASE (58 TOTAL BLADES)
READ BELOW ABOUT EACH ITEM IN THIS MASTER SET
(scroll down to read the complete description)
INCLUDES OFFSET, MINI, MEDIUM AND EXTRA LONG
Offset Valve Tappet Feeler Gauge = Speeds valve lash adjustment. Install the proper blades for intake and exhaust settings and avoid fumbling with multiple blade stacks. Comfortable plastic handles with knurled nuts to hold blades securely.
Offset blades for easy insertion. Blades are marked in both inch and metric. Eleven sizes from .004" to .014" (0.102mm to 0.356mm)
Metric (REGULAR LENGTH)
25 Straight Blade Feeler Guage
The blades in this REGULAR LENGTH set are metric sizes.
0.04 thru 1.00mm
Thickness In millimeters

0.04 0.15 0.50 0.85 .000
0.05 0.20 0.55 0.90
0.06 0.25 0.60 0.95
0.07 0.30 0.65 1.00
0.08 0.35 0.70
0.09 0.40 0.75
0.10 0.45 0.80


YOU ALSO GET
MINIATURE FEELER
17 Blade Mini Feeler Gauge 17 straight blades

VERY SMALL
1 1/2" long x 1/4" wide
010, .012, .013, .015, .016, .017, .018, .019, .020, .022, .024, .025, .026, .028, .030, .032, .035.

PLUS 25 BLADE EXTRA LONG FEELER GAUGE SET
For long reach applications especially diesel.
12 Inch blades
.0015., .002, .003, .004, .005, .006, .007, .008, .009, .010, .011, .012, .013, .014, .015, .016, .017, .018, .019, .020, .021, .025, .027, .030, .040". Blades also marked with metric equivalent. Knurled nut allows blade removal.


REMINDER: THIS IS A MASTER SET WITH FOUR DIFFERENT TYPES OF FEELER GUAGES
INCLUDES OFFSET, MINI, MEDIUM AND EXTRA LONG WITH A GRAND TOTAL OF 58 BLADES
YOU GET ALL FOUR ITEMS WITH THIS PURCHASE

4 PIECE SCRAPER SET 39.99
4 PIECE SCRAPER SET
Set includes: stubby scraper; 1" carbon scraper; combination offset scraper; and 5/8" scraper. Made in U.S.A.
Excellent for the Professional or Shadetree Technician!
Set 3 XZN Tools 37.50
Set 3 Triple Square XZN Tools
Including sizes M18, M16 and M14
The 14mm 12 point socket with tamper proof hole Services 2003 and up VW Touareg and Porsche Cayenne Front Axle Bolts, various Audi/VW Axle Bolts plus Audi TT Differential Mount Bolts and Transmission Drain Plug.

The size 16mm Drain Plug Socket is a Special Tamperproof Transmission Drain Plug tool. Triple Square 12 Point for VW and Audi with ZF Transmissions Same as Volkswagen Tool 3357. For Porsche Boxster and Audi A4, A6 and Passat

The 18mm socket services Oil Drain Plugs and Engine Head Bolts on 2006 & up VW Bora and Touareg. Rare and hard to find sizes in this set!
Use with 1/2" square drive tools.

You get all three tools with this purchase.
Pulley/Fan Belt Pin Wrench 34.95
This Pulley Wrench is used for securing the generator from rotating during R&R of pulley or fan belt. Applicable: Porsche model 911 1975 and newer. (Please note: The Porsche ref. number for this item would be P208B)
Aluminum Soft Jaw Vise Blocks 39.99
Soft Jaws!
Pair of 5" soft jaws machined from aluminum. V slots put a better grip on round objects. Each jaw has a small and large vertical slot.
A large horizontal slot runs the length of each jaw.
Strong magnets attach soft jaws firmly to 4", 5" and 6" vises.
Aluminum Soft Jaw Vise Blocks
SUPER HIGH QUALITY TOOLS
Mini Ignition Wrench Set 34.50
Metric Ignition Wrench Set 8 Pc. auto tools High Quality Tools Sizes Included: 4mm, 4.5mm, 5mm , 5.5mm, 6mm, 7mm, 8mm & 9mm 15 x 60 Deg. heads. Miniature Wrench Sets are available in metric and inch sizes. These sets are perfect for the miniature fasteners found in many electrical, mechanical and computer components of todays vehicles. All wrenches are made of high alloy steel, heat treated, and chrome plated. Sets are supplied in durable vinyl tool rolls. Picture is for reference only. This is a Metric set.
Engine Holder 996 379.00
NEW ... Professional Engine Holder P201 996
Supports the entire weight of a fully dressed LIQUID COOLED twin turbo Boxer 6 engine without having to remove the flywheel. It is manufactured with at least 3 special features that far exceed the O.E.M. design. This fixture is Lighter, Stronger with no hassle to mount and LESS EXPENSIVE! (should be used in conjunction with bench clamp VW313) will allow a full 360 degree rotation of engine. Applicable: Porsche 996 97 thru 08 Boxster and Caymen.
Adjustment Guage Pack 29.95
Adjustment Guage Pack; USED FOR CHECKING AND ADJUSTING BUMPERS ON HOOD LID AND DOOR SEALS. Excellent for the professional or shadetree technician.
Super Mini Ratchet 18.99
SUPER SLIM RATCHET
The Lowest profile head in the industry!
LOOK >>>this tool is only 3.5 inches long!
The quick disk on the drive head allows
for quick tightening/or loosening of fasteners when ratcheting is not required.
Reversible 52 tooth gear head requires only 7 degrees of sweep
Polished Chrome Heat Treated Alloy Steel
Works with all 1/4 Hex Bits
Limited Lifetime warranty
Patented Worldwide
See more images Here!
9 Piece XZN Combo Set 48.50
STUBBY XZN TRIPLE SQUARE 8 PIECE SET PLUS 1 BONUS PIECE
You will get a total of nine (9) Tools with this purchase.
You get the 8 piece set plus the tamperproof socket size M16 for Transmission drain plugs.
(see image above and read below)
Everyone wants the XZN sockets lately and you also find you eventually need the M16 tamperproof piece too,
and so we put this set together for the Porsche Audi VW people.

Socket Set
3/8 Drive
Sizes included: 4mm, 5, 6, 8, 10, 12, 14 and 16mm
(The bonus piece is rare and hard to find for less than 13 dollars)
The 8 piece set comes as shown in the plastic carrying case.
Sturdy compact one piece design.
Satin Chrome with black impact tips.
Super "New" S2 Alloy Steel. Fully Heat Treated
The strongest drivers available!!
Metric Sockets. These are Triple Square Tools
XZN = means Triple Square or 12 point.
If your tool books call for XZN or TRIPLE SQUARE or 12 POINT, these are the tools you need.
These are Short Pattern or what we call "Stubby" Sockets.
Each tool is 1 1/2 inches long.
You will notice the diagram on the upper left is standard XZN
and the diagram on the upper right shows the bonus piece has a HOLE in the tip (tamperproof).
This is a great set for the German car technicians and especially for VW Audi people.
Switch Blade Radio Keys 29.95
O.E. ANTI THEFT RADIO KEY SWITCH BLADE
Special features: (FULL COVERAGE FOR VW AUDI)
Each key folds into the body handle like a pocket knife.
Each half of the tool kit allows for an even pulling action.
SEE MORE IMAGES BELOW
The two halves slide and are held together via an interlocking channel.
Every Key in the kit is current up to 2005.
The full application range of this new kit is as follows:

Updated application key kit for Mercedes & all Porsche 996 and Boxster equipped with Becker radios.
Updated key combo for all Audi & VW radios up to 2004: models equipped with four horizontal (Audi) or two vertical slots (New Beetle, Jetta, etc.).
VW only key kit for Passat, Jetta, Golf models. This key application range ends where key kit 2 begins.
Five sided "pentagon" driver for most every BMW model, excluding E38 & E39 models.
Special Allen key for BMW E38 and E 39 models.
Standard "barbed hooks" (like U Hooks) for Ford, Chevy, Saab, Land Rover, etc.
Tension Guage 35.00
V BELT TENSION GAUGE Permits user to tension belts during installation, while engine is shut off, to maintain belt service life and performance. Use for tensioning all automotive V belts up to, and including, 7/8? top widths. Easy to use. Instructions included Useful tips on correct tensioning and maintenance, as well as average tension values are enclosed. Scale reads in pounds and kilograms. Measures tension from 30 to 160 lbs., and 15 to 75 kg. Die cast aluminum body, nylon Indicator arm and pressure pad. Fits in shirt pocket with stainless steel clip. NOTE: Not for use on timing belts... Tension is of the utmost importance for V belt performance and service life. Applying the correct tension is easy with this tool. It also allows control and maintenance of the optimum tension after installation. The scale indicates the tension in both kg and pounds. Can also be used for tension control of narrower Micro Vbelts (3 4 ribs). Not for timing belts. Porsche 000 721 957 40
Cam Securing Fixtures 993 264.50
Cam Securing Fixtures Pair (2 tools) There is absolutely no way to service cam timing w/o the use of these Securing Fixtures. They correctly position the Left and Right cam shafts. Removing the cylinder heads without them is not recommended.
Applicable: Porsche model 993.
Cylinder Clamp Set 14.99
WHEEL CYLINDER CLAMP SET Keeps wheel cylinder pistons in place during brake replacement Automatically adjusts to fit most double piston wheel cylinders 2 spring steel clamps.
Set P255 for Porsche 175.00
Special tools (2) For the Porsche technician, independent or otherwise. These are Factory correct tools 996 engines up through 2001and Boxster engines up through 2002. pLEASE NOTE: If you are looking for the complete set search for our set number P260...this sale is for two piEces only set number P255.
Metric Copper Washer Assort. 94.50
Metric Copper Seal Ring Assortment 225 Pieces with metal carrying case.
Copper Crush Washers (Sealing) Rings
Comes in the heavy duty metal case with plastic drawer type insert.
Sizes and Quantities below:
4 x 8 = 15 pcs
5 x 9 = 15 pcs
5.5 x 8 = 15 pcs
6 x 12 = 15 pcs
8 x 11.5 = 15 pcs
8 x 14 = 15 pcs
10 x 14 = 15 pcs
10 x 16 = 15 pcs
12 x 15.5 = 15 pcs
12 x 18 = 10 pcs
14 x 20 = 10 pcs
15 x 19 = 10 pcs
16 x 22 = 10 pcs
17 x 23 = 10 pcs
18 x 24 = 10 pcs
20 x 26 = 5 pcs
21 x 27 = 5 pcs
22 x 28 = 5 pcs
24 x 32 = 5 pcs
26 x 32 = 5 pcs
30 x 36 = 5 pcs
Windshield Washer Aiming Tool 19.99
Nozzle Adjusting Tool Made in Germany by Hazet
Telescopic handle with magnetic head 6 mm , adjusting needle, guard cap and pocket clip, for adjusting the nozzles of the washing system. The telescopic handle can be used to demonstrate the jet of the nozzles to the window. Be sure to click on the Link below for more pictures of this tool.. Click here to see more images of this Hazet tool...
Product Search

News

Events